CMSIS limits the stack size, but for qemu_x86_64, qemu_xtensa, qemu_leon3
and the boards sunch as up_squared, ehl_crb, acrn_ehl_crb need more
stack size to run this successfully, or the stack overflow will happened.
So we enlarge the stack size to 1024 for this sample case.
For other boards the original 512 is enough.
Signed-off-by: Enjia Mai <enjia.mai@intel.com>
Search and replace `message(INFO " ` with `message(STATUS "`.
This would otherwise print "INFO <message"
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Change the function pm_device_runtime_enable() to return 0 on
success or an error code in case of error.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
- fixes sample codes' relative paths
- updates instructions to build and run for native posix
platforms on its 64 flavor.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Many documents relied on single quotes to create references, e.g.
`my_reference`. This is possible because `default_role = "any"` is
enabled in Sphinx conf.py. However, this method comes with its problems:
- It mixes all domains together, so it's not clear to what are you
referencing: a document? a Kconfig option? a C function?...
- It creates inconsistencies: in some places explicit roles are used
(e.g. :ref:`my_page`) while in some others not.
- _Conflictis_ with markdown. Single quotes are used for literals in
Markdown, so people tend to use the same syntax in Sphinx, even though
it has a different purpose.
Usages have been found using `git grep ' `[^`]*` ' -- **/*.rst`.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Replace deprecated macro USBD_CFG_DATA_DEFINE by
USBD_DEFINE_CFG_DATA which places usb_cfg_data structures
in specific iterable section.
Replace __usb_data_start, __usb_data_end usage patterns
size_t size = (__usb_data_end - __usb_data_start);
for (size_t i = 0; i < size; i++) {...}
by
STRUCT_SECTION_FOREACH(usb_cfg_data, ...) {...}
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Rework samples to use DEVICE_DT_GET and DT_CHOSEN
to get default display controller device.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Enable the flash on RT1170 and RT1160. When booting from the CM7 core,
flash will be started in XIP mode and used as storage as well as boot
memory. When booting from the CM4 core, flash is available as storage
only, and does not run in XIP mode.
This commit was tested with the following samples
-flash_shell
-littlefs
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Added board specific configuration which enables use of
asynchronous UART API in UART log backend.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This corrects the directory pointing to sample in the README
file. Also changes the TCP port number for the second serial
port exposing the GDB stub. This allows QEMU itself to expose
GDB interface through port 1234, and Zephyr's GDB stub at
port 5678.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The device PM subsystem _depends_ on device, not vice-versa. Devices
only hold a reference to struct pm_device now, and initialize this
reference with the value provided in Z_DEVICE_DEFINE. This requirement
can be solved with a forward struct declaration, meaning there is no
need to include device PM headers.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
In the current USB device support, the sizes of bulk endpoint
are mostly configure through Kconfig and do not care if a device
is high-speed capable. The information if a USB device controller
supports high-speed comes from devicetree. Add a Kconfig option to
map this information and configure bulk endpoint sizes
accordingly.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
uart_fifo_read() can return negative values in case
it is not implemented or CONFIG_UART_INTERRUPT_DRIVEN
is not enabled. Both cases can not actually happen in the
case of CDC ACM UART, check it anyway in case behavior
of the UART API changes unnoticed.
Align the code in RX path code of both camples and
enable TX interrupt only if data was received successfully.
Fixes: #39835Fixes: #39824Fixes: #39809
Coverity-CID: 240667
Coverity-CID: 240679
Coverity-CID: 240697
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
This changes k_mem_domain_init() to return error values
instead of asserting when errors are encountered.
This gives applications a chance to recover if needed.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove option CONFIG_USB_UART_CONSOLE where it has no influence
or enable CONFIG_SHELL_BACKEND_SERIAL_CHECK_DTR without taking
a detour through CONFIG_USB_UART_CONSOLE.
Check the compatibility of chosen property instead
of usage of CONFIG_USB_UART_CONSOLE option.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
This sample uses console driver and therefore
Kconfig option CONFIG_CONSOLE and CONFIG_UART_CONSOLE
are required.
Kconfig option CONFIG_USB_UART_CONSOLE no longer has
any influence here and should be removed.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Currently the IPM samples are hosted in the IPC sample location. Clean
this situation up by moving the IPM samples to a new location.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This change implements qsort() for the minimal libc via Heapsort.
Heapsort time complexity is O(n log(n)) in the best, average,
and worst cases. It is O(1) in space complexity (i.e. sorts
in-place) and is iterative rather than recursive. Heapsort is
not stable (i.e. does not preserve order of identical elements).
On cortex-m0, this implementation occupies ~240 bytes.
Fixes#28896
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
Remove the DT_CHOSEN_ZEPHYR_CANBUS_LABEL macro and replace it with
DEVICE_DT_GET(DT_CHOSEN(zephyr_canbus)) were possible.
Where both devicetree CAN controllers and Kconfig specified CAN loopback
controllers are supported, the macro is replaced with
DT_LABEL(DT_CHOSEN(zephyr_canbus)) for now.
This is the first pass for removing the requirement for devicetree
labels for CAN controllers.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Kconfig USB_DEVICE_REMOTE_WAKEUP option depends only on
USB device controller capability, but is not controlled
by the USB device controller drivers configuration.
Move USB_DEVICE_REMOTE_WAKEUP option to drivers and
make it promptless.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Rename the Zephyr chosen property for specifying the default CAN bus
controller from "zephyr,can-primary" to "zephyr,canbus".
The "zephyr,can-primary" property name was selected in antipation of
adding support for redundant CAN networks, which we have yet to
add. Meanwhile, the "primary" term causes confusion for non-redundant
CAN bus configurations (and the "can" term doesn't match the name of the
Zephyr CAN bus subsystem).
The CAN in Automation (CiA) 302-6, which deals with CANopen network
redundancy, uses the terms "default interface" and "redundant
interface". If/when we add support for redundant CAN networks, the
"zephyr,canbus" chosen property can be supplemented with a
"zephyr,canbus-redundant" chosen property.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
As part of the work to support multiple IPC instances / backends using
IPC service, the static vrings mi code must be reworked to resemble a
classic device driver.
Fix also the sample using it.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
The PM callback is no longer referenced as "pm_control" but
"pm_action_cb", so reflect this new naming on the callbacks.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move all PM device runtime API calls from pm_device* to the
pm_device_runtime* namespace.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
After the removal of pm_device_get_async, the pm_device_wait API has
become redundant. Its usage after pm_device_put_async should not be
considered a valid usecase, since after that call what will happen is a
pm_device_get (which is blocking).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
As of today there is no clear usage of asynchronous gets, since in
general, a resume operation should be synchronous (we are about to use
the device immediately after resuming it). Removing this API simplifies
the runtime implementation in a significant way (refer to future
commits).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Convert remaining tests and samples to using find_package() instead of
literally including the CMake boilerplate code.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
After the __printf_like validation was added to the shell_fprintf
functions we got warnings while building the
'samples/subsys/shell/shell_module' due to incorrect specifiers
while printing size_t variables. Fix that.
Fixes: #39386
Fixes: fe2075d140 "shell: Add __printf_like to shell_fprintf"
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
Uses the stats subsys to provide simple but useful debugging stats for
power management state changes and timing.
Removes the no longer needed PM_DEBUG config option
Replaces the use of PM_DEBUG for a test clock output pin for mec1501 and
adds in its place an SoC Kconfig option to enable it.
Adds a STATS_SET macro for assigning a value to a stat group field
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
This commit adds a new subcommand to the `demo` command that prints out
the name of the used board.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
cAVS 1.5 has little RAM, force COMP_SRC_TINY to fix SOF build
failures under Zephyr with XCC.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
tracing.osawareness.openocd relies on the CONFIG_THREAD_NAME is
enabled, however we don't enable it in test config.
Fix that.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
The tracing.osawareness.openocd doesn't support executing
on multicore Zephyr. However we disable multiple CPUs
usage in two different ways for this test:
- by setting CONFIG_MP_NUM_CPUS to 1
- by setting CONFIG_SMP to n
It's not correct for all SMP platforms to disable SMP. As
it is also excessive (we can guarantee the execution on
single core by setting CONFIG_MP_NUM_CPUS=1) let's drop
SMP disabling.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Evgeniy Paltsev <PaltsevEvgeniy@gmail.com>
Only one single IPC service backend is currently present: multi_instance
backend. This backend is heavily relying on the RPMsg multi_instance
code to instanciate and manage instances and endpoints. Samples exist
for both in the samples/subsys/ipc/ directory.
With this patch we are "unpacking" the RPMsg multi_service code to make
it more modular and reusable by different backends.
In particular we are re-organizing the code into two helper libraries:
an RPMsg library and a VRING / virtqueues static allocation library. At
the same time we rewrite the multi_instance backend to make fully use of
those new libraries and remove the old multi_instance sample.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
