Added dts overlay and config to support using
samples/driver/apa201 with blueclover_plt_demo_v2_nrf52832.
Signed-off-by: Jeremy Wood <jeremy@bcdevices.com>
Search and replace `message(INFO " ` with `message(STATUS "`.
This would otherwise print "INFO <message"
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Sample should only be run if led is present on board.
Since, this is not the case on any of the in tree boards,
set the sample as build-only.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rework samples to use DEVICE_DT_GET and DT_CHOSEN
to get default display controller device.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Deprecate the use of CAN-specific error return values and replace them
with standard errno values.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This adds an spi master mode driver via bitbanged gpio. Only syncronous
transfers are implemented. Clock signal timing is accomplished via busy
waits, the gpios are manipulated via the standard gpio interface; these
two factors limit the frequency at which it can operate - but here
a simple and generic implementation was chosen over performance.
The driver supports the various clock polarity and phase
configurations, and can also work with word sizes which are non
multiples of 8bits, currently up to 16 bits.
A sample program is also added demonstrating basic use of the driver
with 9bit data words.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Pinctrl is missing in i2c1 device description on stm32373c_eval
ovderlay file, besides using I2C1 this board (as mentioned in readme)
requires to remove 2 resistors on the board.
Make it simple and instead use a board with arduino_i2c port
available.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Since drivers implement a callback based on action and not the state,
we should be using the API based on the action instead of the one based
on the state.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Currently the IPM samples are hosted in the IPC sample location. Clean
this situation up by moving the IPM samples to a new location.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Rename the Zephyr chosen property for specifying the default CAN bus
controller from "zephyr,can-primary" to "zephyr,canbus".
The "zephyr,can-primary" property name was selected in antipation of
adding support for redundant CAN networks, which we have yet to
add. Meanwhile, the "primary" term causes confusion for non-redundant
CAN bus configurations (and the "can" term doesn't match the name of the
Zephyr CAN bus subsystem).
The CAN in Automation (CiA) 302-6, which deals with CANopen network
redundancy, uses the terms "default interface" and "redundant
interface". If/when we add support for redundant CAN networks, the
"zephyr,canbus" chosen property can be supplemented with a
"zephyr,canbus-redundant" chosen property.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
As the already existing macro K_MEM_SLAB_DEFINE results in
two variable definitions, the preceding static modifier leads to
a seemingly working solution, though linkage conflicts will occur
when the same memory slab name is used across multiple modules.
The new K_MEM_SLAB_DEFINE_STATIC macro duplicates the functionality of
K_MEM_SLAB_DEFINE with the difference that the static keywords are
internally prepended before both variable definitions.
The implementation has been tested on my Zephyr project (the build
issue faded out). The documentation has been updated altogether
with all incorrect occurences of static K_MEM_SLAB_DEFINE.
Signed-off-by: Pavel Hübner <pavel.hubner@hardwario.com>
Enable watchdog timer on RT1160 evk. This was tested using
the watchdog timer api test (tests/drivers/watchdog/wdt_basic_api)
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
ADC support verified with driver sample. LPADC1 channel 0 pin used,
which maps to pin 10 on J9 on the EVK.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit adds the support to run the SPI NOR sample code on the
npcx7m6fb_evb and npcx9m6f_evb boards.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Change-Id: I780c5dfcf53f3ac537da946673fc03f5ee24e90c
Use a more precise Kconfig symbol name to avoid namespace conflicts when
more NRFX-dependent drivers will be added.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Convert remaining tests and samples to using find_package() instead of
literally including the CMake boilerplate code.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Enables ADC1 on the RT1020 evaluation board. Channels 10 and 11 of this
ADC are exposed as pins 1 and 2 of J18 on the evk.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Enables ADC on RT1015 evaluation board. Channels 1 and 13 are exposed as
pins 2 and 1 of J18 on the EVK.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Added ADC support to RT1010 evaluation board. ADC channels 1 and 2 are
exposed as pins 10 and 12 of J26.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Adds ADC support to RT1024 EVK. ADC channels 10 and 11 are enabled as
pins 2 and 4 on J18 of the evaluation board
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Enables the ADC on the RT1060 evaluation board. Channels 0 and 15 of
ADC1 are available on pins 1 and 0 of J23, respectively.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Make use of the new MBOX APIs to create a ping-pong sample application.
This sample is using the NRFX IPC peripheral to send and receive signals
on different channels
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Moves DAC driver configuration defaults from the application level to
the board level for the bl5340_dvk board.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Moves DAC dts node and driver configuration defaults from the
application level to the board level for the bl654_dvk board.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Moves DAC dts node and driver configuration defaults from the
application level to the board level for the bl653_dvk board.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Moves DAC dts node and driver configuration defaults from the
application level to the board level for the bl652_dvk board.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Refactors all of the counter drivers to use a shared driver class
initialization priority configuration, CONFIG_COUNTER_INIT_PRIORITY, to
allow configuring counter drivers separately from other devices. This is
similar to other driver classes like I2C and SPI.
The default is set to CONFIG_KERNEL_INIT_PRIORITY_DEVICE to preserve the
existing default initialization priority for most drivers. The
exceptions are the maxim_ds3231 and mcp7940n drivers which have a
dependency on a SPI driver and must therefore initialize later than the
default device priority.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
add adc to board dts file,
update yaml files and documentation,
add adc 1 channel pins 1 and 15 to the pinmux file,
add overlay file to the board adc sample,
add board to the adc test file and
Signed-off-by: Andrei Auchynnikau <ovchinnikov@strim-tech.com>
Add __printf_like modifier to validate strings used by shell.
Fixing warnings triggered by this change.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The sample from samples/drivers/misc/ft800/ causes twister to
timeout as it has no pass conditions defiend nor producess any
output that can be verified. What is more, it requires a shield
which is not reflected in the sample.yaml. This fix sets test harness
to display and adds an entry for the required fixture.
Fixes: #38536
Signed-off-by: Maciej Perkowski <Maciej.Perkowski@nordicsemi.no>
Twister was failing for samples/drivers/audio/dmic with timeout
because there were no pass conditions defined. This patch sets
harness to console and adds regex entries to be checked.
Fixes: #38532
Signed-off-by: Maciej Perkowski <Maciej.Perkowski@nordicsemi.no>
Since commit 718c77a4cd ("dts: arm: stm32f0 soc serie has dma of type
V2bis"), the DMA DT cell of STM32F0 MCU has been fixed. It now has three
elements instead of five previously.
This patch fixes the dma property used in nucleo_f070rb.overlay
accordingly.
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
This adds shell support for FPGA drivers.
Signed-off-by: Mateusz Sierszulski <msierszulski@internships.antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
This adds driver for EOS_S3 SoC FPGA.
Signed-off-by: Mateusz Sierszulski <msierszulski@internships.antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
The HiFive Unleashed and HiFive Unmatched boards do not enable the
SPI0 controller that the flash is connected to. This test will not
build on these platforms because SPI0 bus controller is missing.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
This patch fixes printf format specifier "%u" -> "%zu" for printing
an argument of size_t on 64bit environment.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Add a very simple application intended to show how to use the Audio
DMIC API and also to be an aid in developing drivers to implement
this API.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
