Add board support for NXP i.MX8M Plus EVK. This board has the following
features:
Processor : i.MX8M Plus Quad applications processor
Memory : 32-bit LPDDR4 w/6 GB
eMMC 5.0/5.1 w/32 GB
SD/MMC connector
QSPI w/32 MB
Connectivity : MIMO 2x2 Wi-Fi 802.11b/g/n/ac and BT 4.2
2x Ethernet (1x w/ TSN)
PCIe M.2
2x CAN FD DB9 Female connectors
USB : USB 3.0 Type C for Power
USB 3.0 Type A
USB 3.0 Type C
Debug : JTAG connector
MicroUSB for debug console
More information about this board can be found in NXP website: https://www.nxp.com/design/development-boards/i-mx-evaluation-and-development-boards/evaluation-kit-for-the-i-mx-8m-plus-applications-processor:8MPLUSLPD4-EVK
Signed-off-by: Chris Trowbridge <chris.trowbridge@lairdconnect.com>
When building for an STM32K010xB MCU, there is a deprecated properties
warning, which should be fixed by this PR.
Signed-off-by: Wouter Cappelle <wouter.cappelle@crodeon.com>
Everything I can find as a reference says that the LP-SRAM block on
these devices is 64kb, and direct experimentation with cAVS 1.5 and
2.5 agrees. Access to areas beyond 64k hangs the DSP (it should cause
a PIF fault I guess, but the exception never gets trapped, that's
probably a different problem).
Fix this in devicetree to reflect what actually works. It's not clear
where the 128k values came from; if they're not typos we can correct
that when we find better docs.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Create an explicit ina230 driver which is supposed to
work with 230 and 231 variants. While at it switch
to i2c_dt_spec helpers and change device-tree node
names to use - instead of _ in order to follow
convention.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
Create a common properties file that will be included by all bindings
(as i2c and spi) handled by lps22hh driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
PSL_IN pin select register is Vsby power-up reset. When the other
core-domain-reset reset the chip, PSL_IN3/4 don't set to GPIO. This
commit adds PSL_IN3/4 to the pin select list in NPCX devicetree. So
these pins can be set to GPIO when the other core-domain-reset.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
GPT base address in the devicetree for the RT11xx SOC series was
incorrect, this commit fixes it
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Added a driver to enable the GPT timer on RT1xxx parts to be used
instead of systick as a clock source. The timer is set to run in reset
mode, and uses the low frequency 32kHz oscillator for power savings
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add support for the 8 channels TCA9548A I2C mux.
Added a new binding ti,tca9548a binding inheriting
properties from ti,tca954x-base and defining its own compatibles fields.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Add an optional "reset-gpios" phandle-array
field to the driver common yaml.
The reset GPIO channel and pin can be defined
in device tree as a node property.
The driver then deassert the reset signal at mux
initialization if a "reset-gpios" has been specified.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Prepare the driver to upcoming support of more mux references.
Rename all TCA9546A related files to TCA954x.
Keep ti,tca9546a and ti,tca9546a-channel compatible
for backward compatibility reasons.
New tca954x-base binding embedding common properties,
tca9546a binding inherits from it and define its own compatibles fields.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Include the mem-region bindings for the stm32 ccm nodes and set the name
in the current dtsi files.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Add the compatible property to the board level sdram nodes in few stm32
dts files so that the zephyr,memory-region name is used correctly in the
linker script.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Add bindings for SDL based display controller.
Rework SDL based display controller driver to obtain
configuration from devicetree. Remove unnecessary casts,
add multi-instance support.
Add display controller node and chosen property
to native_posix devicetree.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Include common display controller bindings.
Add required height and width properties to "ilitek,ili9340"
and "ilitek,ili9488" users.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Not all boards use the same UART's defaults properties.
This commit updates device tree declarations by deferring
specific definitions to the board's DTS.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Not all boards use the same UART's defaults properties.
This commit updates device tree declarations by deferring
specific definitions to the board's DTS.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Enable flexspi for RT11xx SOCs. This requires selecting the correct
KConfig symbol for the cortex m4 and m7 SOCs, as well as correcting an
error in the flexspi DTS node and updating the clock init for RT11xx
SOCs.
Note that in addition, the NXP hal must be updated to properly support
including the cache management driver for the Cortex M4.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Introduce optional `zephyr,linker-region` property which signifies that
the node should result in a linker memory region and what the name of
that region should be. Property added to compatibles likely to result
in a linker memory region; 'mmio-sram', 'arm,itcm`, `arm,dtcm`,
`nxp,imx-itcm`, `nxp,imx-dtcm` and `fixed-partitions`.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Refactor the mcp230xx driver to generically also support
SPI IO expanders, renaming it to mcp23xxx in the process.
Signed-off-by: Peter Johanson <peter@peterjohanson.com>
Add driver for MEC172x QMSPI with local DMA(LDMA). The driver
support SPI asynchronous operation.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
DMA controller is enabled and tested for cortex M7 core. The M7 core was
tested on the loop and channel link transfer tests.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
DMA controller is enabled and tested for cortex M7 core. The M7 core was
tested on the loop and channel link transfer tests.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit adds a generic i2c regulator driver, and enables the NXP
PCA9420 PMIC IC using this driver. The regulator driver also exposes an
additional API in include/drivers/regulator/consumer.h, which allows
drivers to implement support for adjusting voltage levels and current
limits, if their device supports it.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
the RT685 contains an additional flexcomm peripheral, that supports
only I2C. This commit adds this peripheral to the device tree,
and enables pins and clocks for flexcomm15.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
There is currently no information available about the XIP
addresses for the nRF52840 and nRF5340.
Add this via a new 'reg' block in the relevant QSPI nodes, along with
names for the register blocks so they are easier to retrieve.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This board, whose hardware is just a cAVS 1.8 device without an x86
host CPU, started life (as all the cAVS devices did) as a
cut-and-pasted copy of the same basic code.
Because of hardware and schedule limitations, it didn't get the same
unification treatment that all the other platforms did. But it turns
out that in SMP configurations (which... it's not clear if we actually
test on hardware?) it wants to use the cavs_timer driver, which now
uses the new SOC API and not the old one. Which s1000 doesn't expose.
So... I guess we have to continue to cut and paste until we can find
time to unify this. Add a copy of the new shim/IDC headers to this
SOC and expose them via devivcetree.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Adds a driver using the SNVS high power and optionally low power
RTC instances. A device specific function `mcux_snvs_rtc_set` is
provided to update the current counter value.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
GPIO10 was missing from RT11xx DTS, and is required to manage SD card
power. Enable this GPIO.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The commit adds "disk-access" property to fstab bindings to allow
selecting FS_MOUNT_FLAG_USE_DISK_ACCESS while defining file
systems in DTS.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
This adds an spi master mode driver via bitbanged gpio. Only syncronous
transfers are implemented. Clock signal timing is accomplished via busy
waits, the gpios are manipulated via the standard gpio interface; these
two factors limit the frequency at which it can operate - but here
a simple and generic implementation was chosen over performance.
The driver supports the various clock polarity and phase
configurations, and can also work with word sizes which are non
multiples of 8bits, currently up to 16 bits.
A sample program is also added demonstrating basic use of the driver
with 9bit data words.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
MCUX PWM driver used hardcoded clock source. update driver to use clock
bindings to determine PWM peripheral clock frequency.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Adds optional device tree properties to insert delays between spi chip
select assert/deassert and the clock edges, and also between spi
frames and transfers to the mcux flexcomm spi driver. If the properties
are not set, no additional delay is inserted.
Verified expected behavior on mimxrt685_evk and check with a scope
that the pre- and post-delay could be changed from the device tree
properties.
Signed-off-by: Bryce Wilkins <bryce.wilkins@gmail.com>
