The original parameter (k1) setting may let the I2C frequency be a
little bit higher than 100k Hz, which causes the timing Tsu:sta (set-up
time for a repeated START) to violate the spec. This change fixes the k1
parameter and also changes the HLDT to the suggested value in the
datasheet.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
The STM32 docs state that the ADC may not be calibrated unless
the ADC is disabled (ADEN=0). This commit implements this constraint
Fixes#40936
Signed-off-by: Pete Dietl <petedietl@gmail.com>
Change the function pm_device_runtime_enable() to return 0 on
success or an error code in case of error.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Create an explicit ina230 driver which is supposed to
work with 230 and 231 variants. While at it switch
to i2c_dt_spec helpers and change device-tree node
names to use - instead of _ in order to follow
convention.
Signed-off-by: Bartosz Bilas <b.bilas@grinn-global.com>
- B91 SoC requires to set RX mode again if channel is changed
- Fixed wrong ACK packet detection, mask should be used
Signed-off-by: Yuriy Vynnychek <yura.vynnychek@telink-semi.com>
Add checks for the upper boundary in access_read/access_write
instead of the homeopathic ASSERTS.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
This commit aligns lps22hh sensor driver to latest multi
instance sensor driver model.
In particular it makes use of the stmemsc common routines
and move ctx handler inside struct config, so that the
bus_init routines can be totally avoided.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This flag may cause host to more ambitious power saving behavior,
not all Zephyr USB classes or applications may be ready for this
now. Allow to disable option USB_DEVICE_REMOTE_WAKEUP.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
PRE_KERNEL_1 is to be used for devices that have no dependencies
and do not use kernel features, such as those that rely solely on
hardware present in the processor/SOC. This commit updates these
gpios to initialize during the PRE_KERNEL_1 rather than the
POST_KERNEL. Some SoC drivers are moved to PRE_KERNEL_2 due
to dependencies.
A lot of 'other' drivers can depend on GPIOs though phandles
(such as reset lines, data or command gpios, etc...). Most of these
drivers that would need this would come up on the POST_KERNEL,
and it's likely the driver may not be up yet as it should be defined.
Signed-off-by: Ryan McClelland <ryanmcclelland@fb.com>
USDHC driver did not pass disk test (failed during multiple writes). Add
logic to wait for the SD card to be idle before reading new data, so
that the test will pass. Also, add logic to reject OOB reads and writes
to the disk.
Fixes#39942
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
GD32 HAL use two USART status register name, USART_STAT and USART_STAT0.
This add a redefine to make USART_STAT as defaut name.
Signed-off-by: HaiLong Yang <cameledyang@pm.me>
Added a driver to enable the GPT timer on RT1xxx parts to be used
instead of systick as a clock source. The timer is set to run in reset
mode, and uses the low frequency 32kHz oscillator for power savings
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Add support for the 8 channels TCA9548A I2C mux.
Added a new binding ti,tca9548a binding inheriting
properties from ti,tca954x-base and defining its own compatibles fields.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Add an optional "reset-gpios" phandle-array
field to the driver common yaml.
The reset GPIO channel and pin can be defined
in device tree as a node property.
The driver then deassert the reset signal at mux
initialization if a "reset-gpios" has been specified.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Prepare the driver to upcoming support of more mux references.
Rename all TCA9546A related files to TCA954x.
Keep ti,tca9546a and ti,tca9546a-channel compatible
for backward compatibility reasons.
New tca954x-base binding embedding common properties,
tca9546a binding inherits from it and define its own compatibles fields.
Signed-off-by: Aymeric Aillet <aymeric.aillet@iot.bzh>
Make use of the i2c and spi DT APIs introduced in
2946a535 and c894ad12 that get i2c_dt_spec and spi_dt_spec
as input arguments.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The warning below appears once -Waddress-of-packed-mem is enabled:
/__w/zephyr/zephyr/drivers/sensor/bmi160/bmi160.c: In function
bmi160_gyr_channel_get:
/__w/zephyr/zephyr/drivers/sensor/bmi160/bmi160.c:795:23: error: taking
address of packed member of struct <anonymous> may result in an
unaligned pointer value [-Werror=address-of-packed-member]
795 | data->sample.gyr, val);
| ~~~~~~~~~~~~^~~~
/__w/zephyr/zephyr/drivers/sensor/bmi160/bmi160.c: In function
bmi160_acc_channel_get:
/__w/zephyr/zephyr/drivers/sensor/bmi160/bmi160.c:807:23: error: taking
address of packed member of struct <anonymous> may result in an
unaligned pointer value [-Werror=address-of-packed-member]
807 | data->sample.acc, val);
| ~~~~~~~~~~~~^~~~
To avoid the warning, make the struct non-packed, since it is not
necessary in this case given that a union already guarantees that the
pointer to the union points to each member of the union equally..
More info in #16587.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The warning below appears once -Waddress-of-packed-mem is enabled:
/__w/zephyr/zephyr/drivers/gpio/gpio_sx1509b.c: In function
'port_write':
/__w/zephyr/zephyr/drivers/gpio/gpio_sx1509b.c:456:19: error: taking
address of packed member of 'struct sx1509b_pin_state' may result in an
unaligned pointer value [-Werror=address-of-packed-member]
456 | uint16_t *outp = &drv_data->pin_state.data;
To avoid the warning, use an intermediate void * variable.
More info in #16587.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add bindings for SDL based display controller.
Rework SDL based display controller driver to obtain
configuration from devicetree. Remove unnecessary casts,
add multi-instance support.
Add display controller node and chosen property
to native_posix devicetree.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
ssd16xx driver is not well designed and does not pass configuration
via device->config but via struct ssd16xx_data, this was not taken
into account in the commit 4d6d50e2bc
("display: ssd16xx: convert to spi_dt_spec").
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
this allows using a pin numbering scheme as per Espressif's
documentation and HAL usage, where pin counting does not wrap
up when reaching a given number.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Voltage scaling computation should be done in multiple cases.
Add a function that takes into account all cases.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Deprecate the use of CAN-specific error return values and replace them
with standard errno values.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The init responsibility moves to the drivers themselves. The npcx itim
initialize doesn't work now. This adds timer initialization for npcx
itim to fix it.
Signed-off-by: Wealian Liao <WHLIAO@nuvoton.com>
The original code erroneously used:
uint16_t *val;
sizeof val
instead of:
sizeof *val;
This commit fixes this problem and removes an unnecessary
buffer from the stack
Signed-off-by: Pete Dietl <petedietl@gmail.com>
SDK 2.10 changed the PHY API. These updates are
needed as part of moving to SDK 2.10
1. add phy / mdio ops init
2. update PHY_Read/Write HAL call
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Set pinmux driver to use RTCIO interface for to handle
dedicated IOs pull-up/down configuration.
Without this, some GPIOS won't have pull-up enabled
properly.
Also, current implementation automatically disables
output pin when input pin is set. It also performs the
oppositte. This PR changes it only to enable what is
requested, either input or output.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
irq_line and irq_enabled call is not necessary as the interrupt
allocater enables it during its initialization.
it also adds end packet to all write transmission instead
of only at the end (burst data scenario)
Add check in gpio configuration check to avoid wrong gpio pins
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Driver has dedicated workqueue for IRQ processing.
Submit work to dedicated workqueue intead of system workqueue.
It also fixes driver functionality when NET_TC_TX_COUNT is set to 0.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
STM32H7 has different power supply modes but now Zephyr supports just LDO
and direct SMPS. This commit introduses POWER_SUPPLY_CHOICE configuration
parameter and add support for missed power supply modes.
Signed-off-by: Gennady Kovalev <gik@bigur.com>
Fixes#40730.
A dead lock could happen if 2 threads with differents priorities use
poll_out. In fact, the lock data->tx_lock could be lock by a thread with
lower priority and then a thread with higher priority can't take the
lock. There was a race condition here:
/* Wait for TXE flag to be raised */
while (1) {
if (atomic_cas(&data->tx_lock, 0, 1)) {
/* !!!!!!!! RACE CONDITION !!!!!!!!!!!!!!
if (LL_USART_IsActiveFlag_TXE(UartInstance)) {
break;
}
atomic_set(&data->tx_lock, 0);
}
}
To fix race condition, the interrupts are locked in poll_out.
Signed-off-by: Julien D'ascenzio <julien.dascenzio@paratronic.fr>
Refactor the mcp230xx driver to generically also support
SPI IO expanders, renaming it to mcp23xxx in the process.
Signed-off-by: Peter Johanson <peter@peterjohanson.com>
