Only enable netusb for the right configuration of interface and
alt_setting.
Fixes#13560
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Merge cb_usb_status_composite and cb_usb_status and use common
forward_status_cb for both composite and normal devices.
Fixes#14882
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Use standard defined frame size for buffer and wMaxSegmentSize
parameter. Changes frame size from 1522 to 1514.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Commit 766101c was a wrong fix as NETUSB_MTU is the actual network MTU.
Instead of using this value in EEM/ECM drivers, a relevant value should
be set for each there.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Since commit b48a8c3247 ("usb: device: Add composite status callback")
the cb_usb_status callback is not called anymore in composite mode. The
cb_usb_status_composite callback is called instead.
This patch updates the ECM driver to use either one or the other
depending on CONFIG_USB_COMPOSITE_DEVICE.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
And remove the parameter "full" as there is no "ll reserve" distinction
anymore. The parameter was unused since the ll reserve concept removal.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add interface parameter to interface configuration callback to be able
to configure several instances of the same class.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
As rx_buf & tx_buf are defined with a NETUSB_MTU size, this cause
that the frames over 1500 bytes can not be received and are discarded.
Secondly, as fragmentation is not supported (for UDP and TCP datagram),
increase NETUSB_MTU to the maximum possible ethernet frame size :1522
Signed-off-by: Nicolas LANTZ <nicolas.lantz@ubicore.net>
This allows to place instances of the class one after another in the
linker section.
Fixes#12908
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Start of Frame events can now be accessed from USB classes.
This will be useful when implementing idle rate functionality.
Signed-off-by: Marcin Szymczyk <Marcin.Szymczyk@nordicsemi.no>
Couple of findings which were revealed after changing
LOG_MODULE_REGISTER macro:
- missing semicolons after LOG_MODULE_REGISTER()
- missing LOG_LEVEL defines
- other
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Move ECM functionality from netusb to function_ecm making defines not
needed in many cases.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
usb_dc_status_callback() parameters are interface or configuration
numbers and should be const.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Remove all CONFIG_*_EP_ADDR options but keep the default
values for it, as they are necessary to find ep_addr in
usb_ep_cfg_data associated with bEndpointAddress in
interface descriptor.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Adapt functions for new composite interface.
Assign bInterfaceNumber and similar variables of a Interface
default values, these should be valid values for non-composite
configuration. For the case of the composite configuration,
these variables must be set by the interface configuration
function (interface_config) accordingly.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This patch changes all class functions so that the endpoint
address will be retrieved from the usb_ep_cfg_data at runtime.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This fixes a bug in the cdc_ecm Ethernet over USB driver. The ECM
spec (section 3.3.1) says that the end of an Ethernet frame is marked
using the USB short packet mechanisim, where the last packet is less
than the maximum packet size. If the Ethernet frame is a multiple of
the USB maximum packet size then a final zero length packet must be
sent.
Linux however sends a one byte packet (usbnet.c:1393) to work
around hardware issues with zero length packets.
The current Zephyr driver works most of the time except when you send
an Ethernet frame of the right length where the last byte is zero,
such as:
$ ping 192.0.2.1 -s 23 -p 0
Zephyr then drops the last byte, creating a short frame which gets
dropped higher up in the stack.
Signed-off-by: Michael Hope <mlhx@google.com>
netusb endpoint config is specific to the function (ECM, RNDIS, EEM..).
Move this config to the function interface.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Move class_handler and send_pkt to netusb function interface.
This makes netusb 'function' agnostic.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
