Added support for the LE SC pairing with the OOB data. The peripheral
side is only supported for now.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Add an event handler for HCI vendor-specific events with the
event code BT_HCI_EVT_VENDOR.
A vendor defined callback can be registered to be called when
vendor-Specific events are received in the stack. The callback can then
decode and handle the event; if not the stack will decode and handle
the event.
Signed-off-by: Thomas Ebert Hansen <thoh@oticon.com>
When using the procedure Read By Type the response may contain multiple
instances so it needs to be parsed properly. When dealing with long
values only the beggining will be read, for the remaining bytes the
application should issue another bt_gatt_read with offset so Read Blob
procedure is used as recommended by the spec:
BLUETOOTH CORE SPECIFICATION Version 5.1 | Vol 3, Part F page 2312:
The Read Blob Request would be used to read the remaining octets of a
long attribute value.
Fixes#16107
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If the local node keeps getting bombarded with messages, it's possible
that the storage timer gets rescheduled over and over again and never
expires. Add the necessary code to only reschedule the timer if the
new deadline is earlier than an existing one.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The default values for the timeouts, as well as non-defaults in most
Mesh samples, use a higher value for the RPL than then generic mesh
storage timeout. This hasn't had any effect in practice since the code
only uses the RPL timeout if it is *smaller* than the generic one.
The original intention of the code was to use the RPL timeout,
regardless of what the generic one is, whenever the RPL is the only
thing that needs updating. Add some helper macros to track the various
groups of pending flags, and perform the appropriate checks to apply
the RPL timeout whenever it's smaller than the generic timeout, or if
there are no other items to store besides the RPL.
Fixes#15904
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Fix calling bt_gatt_foreach_attr with start handle parameter set
to last static attribute handle.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
settings_read_cb is defined to return ssize_t and not size_t. This
also eliminates several Coverity warnings.
Fixes#15765Fixes#15768Fixes#15771Fixes#15774Fixes#15778
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This reintroduces support for static service in the form of a new API,
BT_GATT_SERVICE_DEFINE, and changes the internal services (GAP/GATT)
to be defined as const as they are never register/unregistered.
Internal service needed to be renamed in order to keep the same order
as before since the section elements are sorted by name.
The result is the following (make ram_report):
before:
gatt.c 572 0.66%
cf_cfg 32 0.04%
db 8 0.01%
db_hash 16 0.02%
db_hash_work 32 0.04%
gap_attrs 180 0.21%
gap_svc 12 0.01%
gatt_attrs 160 0.18%
gatt_sc 80 0.09%
gatt_svc 12 0.01%
sc_ccc_cfg 32 0.04%
subscriptions 8 0.01%
after:
gatt.c 210 0.24%
cf_cfg 32 0.04%
db 8 0.01%
db_hash 16 0.02%
db_hash_work 32 0.04%
gatt_sc 80 0.09%
last_static_handle 2 0.00%
sc_ccc_cfg 32 0.04%
subscriptions 8 0.01%
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Major changes are:
- Expose settings backend API to enable custom backend support.
- Add a new CONFIG_SETTINGS_CUSTOM backend to allow registering a custom
backend.
- Change api of the handlers h_set() routines to allow for
backend-specific read callbacks.
- Provide a customizable settings_backend_init() routine for custom
backends.
- Move runtime settings support to be its own backend.
Signed-off-by: François Delawarde <fnde@oticon.com>
Aligned format specifiers for the Bluetooth Host. Now, the format
specifier matches the variable type.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
This patch adds support for Read Using Characteristic UUID which is one
of the procedure to read the characteristic value especially when the
client only knows the characteristic UUID and does not know the handle
of the characteristic.
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
General MIC fix for AAD lengths up to 14 bytes.
This case doesn't concern the mesh stack because it uses 16 bytes.
Signed-off-by: Reham Tarek <reham.tarek@si-vision.com>
This stores the database hash and check if it has changed on commit
skipping service changed if hash matches.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Custom handlers without any arguments don't since there is a check for
argc > 1, to fix this behavior removing the check.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If handle is over the range end return since handles are always placed
in ascending order.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This reduces bt_gatt_foreach_attr complexity (O(n)) so it can skip
ahead when the start handle is not within its service handles.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It may be very important information for the developer if scanning
fails to start or stop, so add proper logs. There's no need to log
EALREADY errors, since the mesh stack doesn't track the current scan
state and simply relies on the under lying GAP layer to return this
error if the desired state is already set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
bt_gatt_connected should be only called, when there is no
connection error. Change fixes problem with receiving notifications
before connection.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
The commit 8d0ef1eb85 attempted to fix
test case MESH/SR/HM/CFS/BV-02-C, however inadvertently ended up
introducing a hidden bug. This bug was unearthed thanks to commit
686f5c79cf. We have to keep always track
of the FastPeriodDivisor state whether we're using it (faults > 0) or
not (faults == 0). Introduce a boolean field to the model publication
that's used to indicate whether the FastPeriodDivisor should be
applied or not, instead of zeroing the divisor when there are no
faults (this would cause wrong behavior when faults appear again).
Additionally, the PTS seems to require that we wait until the end of
the existing period before sending the next Health Current Status,
rather than sending it immediately when the fault count changes.
Fixes#15365
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Implement the Controller counterpart to CONFIG_BT_WAIT_NOP so that it
issues a NOP Command Complete event after booting up, to signal to the
Host that it is ready to receive HCI traffic.
Fixes#15333
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
When a device is considered unpaired any configuration set in Client
Features shall also be removed.
Fixes#15329
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When calling bt_unpair() the keys were removed from flash, however a
pointer was left to the invalidated keys in case there was an existing
connection. This would then lead to a bogus entry being stored in
flash for a zero-address peer device. Fix this issue by clearing the
conn->le.keys pointer in the bt_unpair() function.
Fixes#15325
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The bt_mesh_fault_update() API is meant for updating the publication
message and sending it out to the network, however it was missing the
necessary call to health_pub_update() which is responsible for
updating the publication message.
Fixes#15300
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Persistent storage is done. So are the configuration and health
clients. We're also not actively looking to optimize the provisioning
protocol & mesh networking memory usage anymore.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Rename reserved function names in the subsys/ subdirectory except
for static _mod_pub_set and _mod_unbind functions in bluetooth mesh
cfg_srv.c which clash with the similarly named global functions.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
The spec allows to set to no specific value with use of 0xffff.
As this still enables entering values in the invalid range, 3200-65535
for min/max interval, this adds the necessary build checks to prevent
values within this range to be used and at same time check if min
interval is not bigger that max interval.
Fixes#15017
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
In order to advertise directed to a privacy enabled central the
initiator field of the directed adv packet needs to set to an RPA.
To instruct the controller to use an RPA in the initiator field own
address type should be set to either 0x02 or 0x03.
Since it is not certain that a remote device supports address resolution
of the initiator address we add an option to turn this on and give the
application the responsibility to check if peer supports this.
Fixes#14743
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
In order to accept string of the same size entered in
CONFIG_BT_DEVICE_NAME_MAX an extra byte must be allocated to guarantee
it will always be NULL terminated.
Fixes#15067
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
There's no need to track this info in prov.c since hci_core.c is
already doing it. Just query hci_core.c always using the
bt_pub_key_get() API.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If PB-GATT is disabled while there are connected clients, those
clients must be disconnected. Add a 'disconnect` parameter to
bt_mesh_proxy_prov_disable() to handle scenarios when we don't want to
disconnect (e.g. right after successfully finishing provisioning) and
tose where we do want to disconnect (e.g. user requesting to disable
the provisioning bearer).
Also make sure that we always update advertising, so that a stale
advertising set isn't left in the controller.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If both PB-ADV and PB-GATT are supported, we need to properly
re-initialize variables such as link.rx.prev_id and (particularly
importantly) link.rx.buf. If we don't do this it may lead to the
following fault when trying to reprovision again:
***** USAGE FAULT *****
Illegal use of the EPSR
***** Hardware exception *****
Current thread ID = 0x20001f10
Faulting instruction address = 0x0
Fatal fault in thread 0x20001f10! Aborting.
Fixes#14928
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Remove unnecessary const keywords (the entire struct is const) and use
bool instead of u8_t for the require_link member.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Using settings_delete() makes it much easier to understand what the
code is doing, and actually also reduces the amount of code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
