import linux-v5.1:Documentation/devicetree/bindings/vendor-prefixes.txt
Use vendor-prefixes.txt to check vendor prefixes
used in compatible strings and property names.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
The legacy PCI support in the DesignWare I2C driver is replaced with
the new PCIe support. The Intel Quark X1000 SoC and the galileo board
configurations are updated accordingly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The SARA-R4 series modules from U-Blox are size-optimized LTE-M /
NB-IoT and EGPRS modules designed for low power consumption and
longer battery life.
The binding identifies the UART device, power GPIO and reset GPIO
lines.
Signed-off-by: Michael Scott <mike@foundries.io>
The label binding was missed during initial development of the
WNC-M14A2A modem. Let's add the binding so that during the
migration to a shield, we can update the DTS correctly.
Signed-off-by: Michael Scott <mike@foundries.io>
Add DTS binding files for the ARM MPU, for both ARM
MPU architecture variants, ARMv7-M and ARMv8-M.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add enum to list what values of maximum-speed are exceptable since
enum's get represented as strings in DT. This also allows us to
generate a code enum to correspond to the string.
We also introduce include/dt-bindings/usb/usb.h which is a hand coded
definition of the enum. We don't have a great way to generate this
right now, however it would be better if we did.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
MHU (Message Handling Unit) enables software to raise interrupts to
the processor cores. It is enabled in SSE 200 subsystems.
This patch aims to implement inter processor communication.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Add LiteX interrupt controller driver and bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add LiteX timer driver with bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add LiteX UART driver with bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Reduced Kconfig for counter with nRF TIMER and RTC. Added overlays
for TIMER and RTC configuration in the counter test.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add support for CLKOUT source selection and divider as found on the
NXP Kinetis KE1xF SoC series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add a new clock control driver for NXP Kinetis SoCs that have the
Peripheral Clock Controller module (PCC).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add bindings for SiFive Data Tightly-Integrated Memory.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Dts Nodes for all the GPIO portswere defined. In addition,
a new binding file was created for the gpio driver.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Expose MEC1501 5 I2C/SMB controllers
Add Microchip specific I2C device tree properties
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
All series of stm32 have at least one ADC instance and this commit adds
one ADC node to the root dts file of each soc, and also adds fixing up
mappings to them.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
The HT16K33 is a memory mapping, multifunction LED controller
driver. The controller supports up to 128 LEDs (up to 16 rows and 8
commons) and matrix key scan circuit of up to 13x3 keys.
This commit adds support for the keyscan functionality of the HT16K33.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
The HT16K33 is a memory mapping, multifunction LED controller
driver. The controller supports up to 128 LEDs (up to 16 rows and 8
commons) and matrix key scan circuit of up to 13x3 keys.
This commit add support for the LED driver functionality of the
HT16K33.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
This adds interrupt support to the SAM0 GPIO driver. This is heavily
inspired by @nzmichaelh work in #5715. The primary difference
from that implementation is that here the External Interrupt
Controller (EIC) is separated out into an interrupt controller driver
that is less tightly coupled to the GPIO API. Instead it implements
more of a conversion from the EIC's own odd multiplexing to a more
traditional port and pin mask IRQ-like callback. Unfortunately,
through the EIC on the SAMD2x are relatively well behaved
in terms of pin to EIC line mappings, other chips that share the
peripheral interface are not. So the EIC driver implements a
per-line lookup to the pin and port pair using definitions extracted
from the ASF headers.
The EIC driver still makes some assumptions about how it will be used:
mostly it assumes exactly one callback per port. This should be fine
as the only intended user is the GPIO driver itself.
This has been tested with some simple programs and with
tests/drivers/gpio/gpio_basic_api on a SAMD21 breakout and an
adafruit_trinket_m0 board.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This adds a SERCOM I2C driver for SAM0 series chips.
Tested with a SAMD21 chip on a SSD1306 display and a MLX90393
sensor. Only compile tested for SAMD20 and SAMR21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Add initial support for the TI CC13x2 / CC26x2 series with the CC2652R
and CC1352R SoCs. The UART and GPIO peripherals are supported. Drivers
use the driverlib HAL from the TI CC13x2 / CC26x2 SDK.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
This adds support for the SAM0 DMA Controller (DMAC). Chained
transfer are not currently implemented.
Tested with tests/drivers/dma/loop_transfer and custom modifications
to that test using three parallel reloading channels. Also tested
with a trivial program that did memory->serial.
Signed-off-by: Michael Hope <mlhx@google.com>
[hageman@inthat.cloud: Rebased and updated commit message]
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This adds support for the async API for SAM0 SERCOM SPI using
DMA to drive the device. This implementation does the reload
for both transmit and receive in the receive DMA handler.
Doing this simplifies the implementation but means that the
transmit drains completely, resulting in the SPI clock pausing
between buffers while both are reloaded in the receive handler.
Tested with tests/drivers/spi/spi_loopback and several simple
programs monitored with a logic analyzer.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This commit adds a flash driver implementation that writes to RAM and
exports statistics through stats.h. It can be used to simulate flash
memory for testing purposes.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
The GPIO driver for the Intel Apollo Lake has so many pins it has to
export ten devices to shoehorn its one device into the GPIO API. The
current implementation uses the shared IRQ driver because these
pseudodevices all share one IRQ. However, since the GPIO driver is
aware of all the possible interrupt sources, it's smaller and faster
(and not even messy) to handle it internally, so this patch eliminates
the dependency on the shared IRQ driver.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Implementation of AMS (Austria Micro Systems) ENS210 temperature and
relative humidity sensor.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Add driver support for Atmel SAM0 device ID, which is 16-bytes long.
The device ID can simply be read from memory at a known location, but
the location is only described in the data sheet, not in ASF.
For SAMD2x it's 0x0080A00C, 0x0080A040, 0x0080A044 & 0x0080A048.
For SAMD5x it's 0x008061FC, 0x00806010, 0x00806014 & 0x00806018.
This adds a new property to the device tree to define the device ID
registers for this SoC family.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Add driver and device tree binding for the Low Power Inter-Integrated
Circuit (LPI2C) controllers found in the RV32M1 RI5CY SoC.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add support for pulsing the hardware reset pin of the FXOS8700 high
during initialization.
According to the datasheet, this is required for the I2C/SPI bus
auto-detection logic to work properly if the VDD/VDDIO power
sequencing order cannot be guaranteed.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Allows to enable initial RTS/CTS hardware flow control
in the dts.
Co-authored-by: Benoit Leforestier <benoit.leforestier@gmail.com>
Signed-off-by: Georgij Cernysiov <g.cernysiov@elco-automation.de>
Adjusted the MCP2515 driver to switch from KConfig SPI configuration to
DTS based configuration.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
The MCP2515 is a CAN controller that can be connected via SPI to an
host MCU. This driver adds support for the MCP2515 as a new driver in
the CAN subsystem.
As it is a SPI peripheral it uses a thread for its interrupt
handling and the received message filtering is done inside this
interrupt thread, as the MCP2515 filter capabilities are not sufficient
for the Zephyr CAN interface.
The driver was validated with an external CAN logger and the adjusted
CAN sample application.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
A parallel PCI implementation ("pcie") is added with features for PCIe.
In particular, message-signaled interrupts (MSI) are supported, which
are essential to the use of any non-trivial PCIe device.
The NS16550 UART driver is modified to use pcie.
pcie is a complete replacement for the old PCI support ("pci"). It is
smaller, by an order of magnitude, and cleaner. Both pci and pcie can
(and do) coexist in the same builds, but the intent is to rework any
existing drivers that depend on pci and ultimately remove pci entirely.
This patch is large, but things in mirror are smaller than they appear.
Most of the modified files are configuration-related, and are changed
only slightly to accommodate the modified UART driver.
Deficiencies:
64-bit support is minimal. The code works fine with 64-bit capable
devices, but will not cooperate with MMIO regions (or MSI targets) that
have high bits set. This is not needed on any current boards, and is
unlikely to be needed in the future. Only superficial changes would
be required if we change our minds.
The method specifying PCI endpoints in devicetree is somewhat kludgey.
The "right" way would be to hang PCI devices off a topological tree;
while this would be more aesthetically pleasing, I don't think it's
worth the effort, given our non-standard use of devicetree.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Enable the clock for GPIO ports on the RV32M1 SoC before attempting to
access the port controller registers.
Fixes: #15339
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
The SYSCFG_CFGR1_PA11_PA12_RMP define is present even on packages where
the remap isn't strictly required. This commit makes the remap optional
based on a DT property.
Also fixes syntax error caused by a missing );.
Signed-off-by: Josef Gajdusek <atx@atx.name>
The erase-block-size and write-block-size are needed for the spi_nor
driver to compile.
scripts/dts/extract/flash.py automatically adds these properties if
this flash device is part of the "chosen" flash node, but they're
otherwise missing.
Signed-off-by: Jim Paris <jim@jtan.com>
1. SW PWM device node added to common nrf5_common.dtsi
2. SW PWM node set in all nRF5x DTSI files.
Different initial settings for nRF51 and nRF52 devices.
Status is ok by default for nRF51.
3. Added yaml binding for Nordic SW PWM node.
4. Set codeowner of nordic dts bindings to @anangl
Signed-off-by: Gaute Gamnes <gaute.gamnes@nordicsemi.no>
