Maybe this is some "just in case" thing that got copied around. There's
no need to have a blank line at the beginning or end of Kconfig files.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
In zephyr drivers should always use u32_t.
Using uint32_t here generates issues in the CI when NEWLIB_LIBC
is defined.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LIS2MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use Kconfig named choice for TRIGGER_MODE in order to easy
up the trigger mode selection in default configurations
for boards using this sensor driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert lis2mdl magnetometer driver to get the device name as well
as i2c slave information from device tree. Updates the build_all
test accordingly.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
i2c_burst_read can fail during read/write procedure. Therefore,
add a sanity check for its return value.
Fixes#11101
Coverity-CID: 189505
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Added support to LIS2MDL Magnetometer sensor provided
with following features:
- I2C interface
- Mag data
- Temperature data
- ODR configurable by config or at runtime
- Trigger mode selectable by menuconfig
- IRQ pin configurable (by dts or Kconfig)
- Hard Iron offset setting at runtime
- Include yaml file
Tested on ST MEMS IKS01A2 + NUCLEO STM32F411RE board.
LIS2MDL connected to I2C master interface (SPI 3 wire not
supported yet).
Test run with all ODR {10, 20, 50, 100} Hz in poll and
trigger mode.
GPIO IRQ dts configuration has been tested by adding
to boards/arm/nucleo_f411re/nucleo_f411re.dts file
this patch:
&i2c1 {
status = "ok";
clock-frequency = <I2C_BITRATE_FAST>;
+
+ /* ST Microelectronics LIS2MDL mag sensor */
+ lis2mdl-magn@1e {
+ compatible = "st,lis2mdl-magn";
+ reg = <0x1e>;
+ irq-gpios = <&gpioa 4 0>;
+ label = "LIS2MDL";
+ status = "ok";
+ };
};
and adding boards/arm/nucleo_f411re/dts.fixup with following
content:
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_LABEL
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_BASE_ADDRESS
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_BUS_NAME
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_IRQ_GPIOS_CONTROLLER
ST_STM32_I2C_V1_40005400_ST_LIS2MDL_MAGN_1E_IRQ_GPIOS_PIN
For more info on this LIS2MDL please follow this link:
http://www.st.com/en/mems-and-sensors/lis2mdl.html
Signed-off-by: Mario Tesi <mario.tesi@st.com>
