It is recommended that multibyte (burst) transfers are used to read
acceleration and temperature data. This ensures the data is concurrent
and complete.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
This commit consolidates the temperature conversion into a single
location and subtracts the bias from the measurement using values from
the datasheet. Also magic numbers have been replaced with more
descriptive macros.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
This driver uses magic numbers which are incorrect. A correct conversion
is done using the LSB/g scale factors given by Table 1 in the
specifications section of the ADXL362 (Rev. F) datasheet. The entire
conversion has also been consolidated into a signal function.
The sensitivity and offset of the accelerometer values actually vary
with the supply voltage and temperature. Using datasheet provided values
for 25 C and 2.0 V is the best we can do. Users will need to apply
sensitivity and offset corrections for their application.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
The return code check and error return on the interrupt register
configuration function call should be included in the #if defined
region.
Fixes#16159
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Clear status bits before mapping them to the interrupt pin, so the
interrupt will occur on the next event instead of a pending event. Also
the status bits are cleared independently, because the threshold and
data ready functions can be enabled simultaneously.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Enabling and disabling the GPIO callbacks is error prone and unnecessary
since the trigger data is protected with a mutex, so it has been
removed. This resolves the following issues:
- The GPIO callbacks are not being re-enabled properly in the error path
of the trigger setting function.
- The device pointer used in the GPIO callback to retrieve the ADXL362
driver configuration data is the GPIO device not the ADXL362 device,
so this cast is invalid and the int_gpio field is garbage.
- There are potential timing issues between enabling interrupts and
re-enabling the callbacks.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Commit 11295c1 added Kconfig options for interrupt mode, but then hard
coded the interrupt mode. This commit uses the Kconfig option to set
the interrupt mode.
Applications expecting the interrupt mode to be something other than
the default will need to be updated.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
The default case of the switch statement jumps over the unlocking of the
trigger mutex. This has been fixed with more granular locking which has
the added benefit of being more explicit about what is being protected.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Implementation of AMS (Austria Micro Systems) ENS210 temperature and
relative humidity sensor.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Add support for pulsing the hardware reset pin of the FXOS8700 high
during initialization.
According to the datasheet, this is required for the I2C/SPI bus
auto-detection logic to work properly if the VDD/VDDIO power
sequencing order cannot be guaranteed.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Refactors the apds9960 sensor driver to get the i2c device name, i2c
device address, gpio device name, and gpio pin from a constant device
configuration structure, rather than using hardcoded macros. This will
make it easier to change the names of the macros and to instantiate
multiple instances of the driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Updated to add support for CS. DT config names updated
to adhere to the DTS naming convention. Init and SPI
configuration now follows the device datasheet.
Signed-off-by: Henrik Malvik Halvorsen <henrik.halvorsen@nordicsemi.no>
The existing device_set_power_state() API works only in synchronous
mode and this is not desirable for devices(ex: Gyro) which take
longer time (few 100 mSec) to suspend/resume.
To support async mode, a new callback argument is added to the API.
The device drivers can asynchronously suspend/resume and call the
callback function upon completion of the async request.
This commit adds the missing callback parameter to all the drivers
to make it compliant with the new API.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Maybe this is some "just in case" thing that got copied around. There's
no need to have a blank line at the beginning or end of Kconfig files.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
1. Remove nrf_common.h include
2. Remove unnecessary NRF_*Type defines, using
CMSIS NRF_TEMP define directly instead.
3. Align driver code by including DEVICE_DECLARE,
and moving DEVICE_AND_API_INIT() to the bottom.
Signed-off-by: Gaute Gamnes <gaute.gamnes@nordicsemi.no>
In zephyr drivers should always use u32_t.
Using uint32_t here generates issues in the CI when NEWLIB_LIBC
is defined.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Update reserved function names starting with one underscore, replacing
them as follows:
'_k_' with 'z_'
'_K_' with 'Z_'
'_handler_' with 'z_handl_'
'_Cstart' with 'z_cstart'
'_Swap' with 'z_swap'
This renaming is done on both global and those static function names
in kernel/include and include/. Other static function names in kernel/
are renamed by removing the leading underscore. Other function names
not starting with any prefix listed above are renamed starting with
a 'z_' or 'Z_' prefix.
Function names starting with two or three leading underscores are not
automatcally renamed since these names will collide with the variants
with two or three leading underscores.
Various generator scripts have also been updated as well as perf,
linker and usb files. These are
drivers/serial/uart_handlers.c
include/linker/kobject-text.ld
kernel/include/syscall_handler.h
scripts/gen_kobject_list.py
scripts/gen_syscall_header.py
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Most of these are from 'source'ing drivers/sensor/grove/Kconfig within
an 'if SENSOR' (in drivers/sensor/Kconfig), and then adding another 'if
SENSOR' within it.
'if FOO' is just shorthand for adding 'depends on FOO' to each item
within the 'if'. Dependencies on menus work similarly. There are no
"conditional includes" in Kconfig, so 'if FOO' has no special meaning
around a source. Conditional includes wouldn't be possible, because an
if condition could include (directly or indirectly) forward references
to symbols not defined yet.
Tip: When adding a symbol, check its dependencies in the menuconfig
('ninja menuconfig', then / to jump to the symbol). The menuconfig also
shows how the file with the symbol got included, so if you see
duplicated dependencies, it's easy to hunt down where they come from.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
vl53l0x driver is using an external library to build, located under:
ext/hal/st/lib/sensor/vl53l0x.
This library is expecting stdint.h lib to be available and to
secure this for driver library inclusion work, a stdint.h file
header check was done. This check was based on assumptions on possible
header names for stdint.h.
Due to recent renaming of the zephyr header files, this check was
returning a false positive, generating warning at compilation.
Rather than updated with new header names, remove this check, since
driver porting is completed and stdint.h inclusion is actually
done.
Fixes#10134
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Generate interrupt on every ALS cycle in non-trigger mode
and enable ALS saturation interrupt.
resolves: #11989
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add support to STM LIS2DW12 3-axis accelerometer driver.
The driver support I2C and SPI bus communication and both
polling and drdy trigger mode.
Co-authored-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use the new i2c_write_read() wrapper to simplify the code.
Also add several overlays used to test the sensor on a variety of
boards, and conf file support for trigger testing.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Use auto-generated device tree macros in LPS25HB driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LSM6DS0 driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
We use DT to get the I2C address, so the define that got it from a
Kconfig sybmol isn't used and the Kconfig symbol isnt defined. Remove
this dead code.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get the following warning with sdk-ng:
drivers/sensor/lis2dh/lis2dh.c:210:38: error: bitwise comparison
always evaluates to false [-Werror=tautological-compare]
if ((value & LIS2DH_LP_EN_BIT_MASK) == 1 && ...
^~
The test needs to be:
(value & LIS2DH_LP_EN_BIT_MASK) == LIS2DH_LP_EN_BIT_MASK
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This belongs in the implementation file that references the array, since
the header is included in multiple files.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Setting bit 3 instead of bit 2 modifies a reserved section of the
register, with the impact that the ODR is not as configured.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Use auto-generated device tree macros in LIS3MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LIS2MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
