Remove NET_CONFIG_IEEE802154_DEV_NAME in favor of DT based choice using
zephyr,ieee802154.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Remove usage of CONFIG_NET_CONFIG_IEEE802154_DEV_NAME as it now works
with DT based choice.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Remove Kconfig choice for IEEE802154. In this case, there's no in-tree
board, so there's no overlay or board to be updated.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use the choisen zephyr,ieee802154 from DT as
CONFIG_NET_CONFIG_IEEE802154_DEV_NAME is being phased out.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use the choisen zephyr,ieee802154 from DT as
CONFIG_NET_CONFIG_IEEE802154_DEV_NAME is being phased out.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Make a library out of the zperf shell sample. This makes to enable the
module in any application, not only the dedicated sample.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
RT1050 and RT1060 were selecting an invalid number of RX/TX buffers
(below the allowed default). Raise this value for the gptp sample.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
enable hardware acceleration of ethernet checksum calculation for
RT1050 and RT1060
Performance change (as tested with iperf on RT1050)
TCP RX: 50.6Mbps->52.4Mbps
TCP TX: 49.5Mbps->50.2Mbps
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Use systick timer for RT1050 to provide better performance than low
frequency GPT timer
Performance change (as tested with iperf on RT1050)
TCP RX: 49.1Mbps->50.8Mbps
TCP TX: 40.8Mbps->46.2Mbps
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
All IEEE 802.15.4 drivers are now automatically enabled if they are
'okay' in DT and all of its dependencies are 'y', including
CONFIG_IEEE802154. This means individual driver enablement is not
necessary anymore in Kconfig.defconfig files or samples/tests. Boards
need to still make sure any dependencies are enabled, e.g. SPI bus in
some cases.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Use Devicetree to describe the UART UPIPE IEEE 802.15.4 driver. This
allows to remove usage of IEEE802154_UPIPE_DRV_NAME in preparation for
the removal of NET_CONFIG_IEEE802154_DEV_NAME.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
samples should not use CONFIG_TEST_EXTRA_STACK_SIZE, instead, they
should set the recommended stack size directly.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
For further details about interoperability testing please see
* https://lwm2m.openmobilealliance.org/ - Test V1.1 12-Sep-2019
Signed-off-by: Veijo Pesonen <veijo.pesonen@nordicsemi.no>
Make sure that the network interface is up before running the sample.
Otherwise, the sample could stop rightaway due to send failure.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
First off, fix the FD check when closing a socket - currently not all
sockets were closed on exit (0 is also a valid file descriptor).
Second issue is the use of k_thread_abort() on tx/rx threads. The
receving thread was blocked in recv(), and aborting its thread prevented
it from ending gracefully (i. e. the socket mutex allocated in recv()
was not released as the function did not exit properly). This resulted
on a consecutive `close()` call lock. Fix this by setting a timeout on a
receiving socket, and instead of aborting threads allowing them to exit
gracefully.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Sample code uses GPIO api's but wasn't enabling CONFIG_GPIO. So
on native_posix this would cause the sample to not build. Add
CONFIG_GPIO=y to prj.conf to fix this.
Fixes#48306
Signed-off-by: Kumar Gala <galak@kernel.org>
Add support for running the SocketCAN sample on
native_posix/native_posix_64 using the CAN loopback interface.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Created the variable CONFIG_LWM2M_SERVER_DEFAULT_SSID to be
the default ssid when not using bootstrap. Needed for access control.
Signed-off-by: Ola Tangen Kulseng <ola.kulseng@nordicsemi.no>
Move the CAN bus network driver from drivers/can to drivers/net as it
implements a network driver, not a CAN controller driver.
Use a separate Kconfig for enabling the CAN bus network driver instead of
piggybacking on the SocketCAN Kconfig. This allows for other
(e.g. out-of-tree) SocketCAN transports.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Move to use DEVICE_DT_GET_ONE instead of device_get_binding as
we work on phasing out use of DTS 'label' property.
Signed-off-by: Kumar Gala <galak@kernel.org>
The use of DT_BUS_LABEL in a logging call can easily be replaced
with uart_dev->name. This moves us slowly forward to removing
use of devicetree `label` property.
Signed-off-by: Kumar Gala <galak@kernel.org>
We don't have anything that build tests the win1500 driver, so
enable reel_board to provide coverage on the driver.
Signed-off-by: Kumar Gala <galak@kernel.org>
In the Zephyr implementation, `sem_timedwait()` uses a
potentially wildly different timebase for comparison via
`k_uptime_get()` (uptime in ms).
The standard specifies `CLOCK_REALTIME`. However, the real-time
clock can be modified to an arbitrary value via clock_settime()
and there is no guarantee that it will always reflect uptime.
This change ensures that `sem_timedwait()` uses a more
consistent timebase for comparison.
Fixes#46807
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
Logging v1 has been removed and log_strdup wrapper function is no
longer needed. Removing the function and its use in the tree.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Cocinelle complains about "shell" being used as a parameter name:
"Violation to rule 5.7 (Tag name should be unique) tag: shell"
Therefore rename the parameter throughout the sample to "sh".
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Rewrite the TCP/UDP download part of the zperf sample to use socket API.
For UDP, performance impact is negligible (< 1 Mbps), for TCP it's
noticable, but still throughputs can be considered satisfactory (up to
~75 Mbps).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Rewrite TCP/UDP upload part of the zperf sample to use socket API
instead of net_context. This has a negligible impact on the upload
throughputs (< 1 Mbps).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This code has gone unmaintained and bugs continue to be reported
against it. We do not have the resources as a project to maintain this
in "odd fixes" mode, and nobody has stepped up to maintain it [1], so
sadly this must be removed for now.
If anyone would like to see civetweb supported in upstream Zephyr
again, they are welcome to add it back, as long as they promise to
maintain it going forward.
Many thanks to everyone who has contributed to civetweb support in
Zephyr while it was here. So long and thanks for all the fish.
Fixes: #45807Fixes: #43910Fixes: #34226Fixes: #46743
[1] https://lists.zephyrproject.org/g/devel/message/8466
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Remove v1 implementation from log_core and all references in the tree.
Remove modules used by v1: log_list and log_msg.
Remove Kconfig v1 specific options.
Remove Kconfig flags used for distinction between v1 and v2.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
...v1.1 overlay
Shows the dependencies which makes it easier to enable the content
format when necessary
Signed-off-by: Veijo Pesonen <veijo.pesonen@nordicsemi.no>
This sample app uses a stack buffer to hold the interface name which is
generated at runtime using sprintk. The buffer is only sized for the
expected range of values, not the full possible range of the datatype
(int).
To mitigate this, increase the size of the buffer to hold the full range of
an int value.
Signed-off-by: Keith Packard <keithp@keithp.com>
By default, any string or opaque data that LwM2M engine initializes
sets data lenght to same value as given buffer length for that
resource.
However, on run time, engine keeps track how much data is written
to each resource, so when reading from any resource, should only
return data that has been written there. But uninitialized resources
return the content of the whole buffer.
Fixed the problem by introducing macros INIT_OBJ_RES_LEN(),
INIT_OBJ_RES_MULTI_DATA_LEN() and INIT_OBJ_RES_DATA_LEN() that
allows you to give the amount of data existing in buffer when
the resource is initialized. This sets the data_len and max_data_len
variables correctly.
Also introduced new functions lwm2m_engine_get_res_buf() and
lwm2m_engine_set_res_buf() that distinct between data size and
buffer size. Deprecated the previous functions
lwm2m_engine_get_res_data() and lwm2m_engine_set_res_data()
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
This dependency it is not required since majoprity of platforms are
working with new pinctrl API. This drops the pinmux dependency.
Fixes#46091
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Since the recent OpenThread update, OT needs more stack to initialize,
therefore bump the stack size in samples using OpenThread.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Convert the can_mode enum to a bit field to prepare for future extensions
(CAN-FD mode, transmitter delay compensation, one-shot mode, 3-samples
mode, ...).
Rename the existing modes:
- CAN_NORMAL_MODE -> CAN_MODE_NORMAL
- CAN_SILENT_MODE -> CAN_MODE_LISTENONLY
- CAN_LOOPBACK_MODE -> CAN_MODE_LOOPBACK
These mode names align with the Linux naming for CAN control modes.
The old CAN_SILENT_LOOPBACK_MODE can be set with the bitmask
(CAN_MODE_LISTENONLY | CAN_MODE_LOOPBACK).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove ESP32 and ESP32S2 from not working samples
and tests. Reason for not working is not enough memory
space in RAM to execute it. This can be worked out as next steps.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
In order to bring consistency in-tree, migrate all samples to the use
the new prefix <zephyr/...>. Note that the conversion has been scripted:
```python
from pathlib import Path
import re
EXTENSIONS = ("c", "h", "cpp", "rst")
for p in Path(".").glob("samples/**/*"):
if not p.is_file() or p.suffix and p.suffix[1:] not in EXTENSIONS:
continue
content = ""
with open(p) as f:
for line in f:
m = re.match(r"^(.*)#include <(.*)>(.*)$", line)
if (m and
not m.group(2).startswith("zephyr/") and
(Path(".") / "include" / "zephyr" / m.group(2)).exists()):
content += (
m.group(1) +
"#include <zephyr/" + m.group(2) +">" +
m.group(3) + "\n"
)
else:
content += line
with open(p, "w") as f:
f.write(content)
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
With LwM2M v1.1 SenML CBOR is preferred over SenML JSON.
TLV is on by default only with v1.0.
Signed-off-by: Veijo Pesonen <veijo.pesonen@nordicsemi.no>
