Use LOG_DBG instead of LOG_ERR when BME680 chip is detected
and its ID verified successfully.
Signed-off-by: Jan Tore Guggedal <jantore.guggedal@nordicsemi.no>
The i2c_msg API details do not work correctly with Nordic TWI. Switch
to the higher-level and simpler API for register read and write. Also
add a tree configuration on a Nordic-based board.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
LSM303AGR is a special one in terms of raw value scale among all devices
supported by lis2dh.c driver. Apply proper scale factor based on
sensitivity scale provided in LIS2DH and LSM303AGR datasheets.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
All values were scaled by 8 instead of 12 for 16g compile-time selected
range. This resulted with values around 6.5 m/s^2. Scaling for runtime
configurable ranges was broken for all except 2g range option due to
totally broken lis2dh_range_to_reg_val().
Fix wrong scaling for 16g compile-time and all runtime selectable ranges
by reworking code that scales raw value. While doing this, change
lis2dh->scale type from 16 to 32 bits. This allows to slightly increase
final result precision by using the fact that raw values have maximum 12
bits precision, allowing us to multiply lis2dh->scale by (1 << 4)
compared to previous implementation.
Fix bug #19872.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
According to struct sensor_value documentation, val2 should be negative
for negative result. So drop code that tries to make val2 positive.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Cast to (void) the lsm6dso_mem_bank_set() calls as we
are not interested to the return value.
Coverity-CID: 205625
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This commit converts the existing hcm5883l 3-axis magnetometer
driver to use device tree for the I2C and GPIO selection.
It also adds a basic sample application for this sensor, using the
frdm-k64f development board to demonstrate how the interrupt
GPIO pin and I2C bus can be selected.
Signed-off-by: Kevin Townsend <kevin@ktownsend.com>
Convert bmg160 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert bmm150 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert max44009 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert mcp9808 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert sx9500 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert tmp112 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert th02 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update lis3mdl-magn dts binding to include GPIO interrupt pin and change
driver code to get the GPIO pin and controller info from DT instead of
Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update ccs811 dts binding to include GPIO pins for wakeup, reset, and
interrupt and change driver code to get the GPIO pin and controller
info from DT instead of Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The LIS2MDL supports SPI half duplex mode with a single data line
by default (3-wire), but it might configured to switch to standard
full duplex mode (4-wire).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Update vl53l0x dts binding to include GPIO XSHUT pin and change
driver code to get the GPIO pin and controller info from DT instead of
Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update the binding for nordic,nrf-temp to require the label property and
use the generated define (DT_INST_0_NORDIC_NRF_TEMP_LABEL) instead of
Kconfig symbol (CONFIG_TEMP_NRF5_NAME).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Some chips supported by lis2dh driver (such as LIS2DH12 and LIS3DH)
contain CTRL_REG0 (1Eh) register to control internal pull-up on SDO/SA0
line (enabled by default). Add disconnect-sdo-sa0-pull-up boolean
device-tree property to allow disconnecting pull-up during driver
initialization. This allows to save around 180uA at 3.6V in
accelerometer power-down mode.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
There is little reason to compile lis2dh_reg_field_update() function
conditionally, based on enabled features. If it is not used, then linker
will drop it anyway.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The default I2C driver on Nordic platforms does not support the I2C
burst operations, so replace those calls with ones that work on the
platform.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The value of BMG160_THREAD_PRIORITY has never been used after the symbol
was added. Use it.
The value defaults to 10 in Kconfig too, so this is a no-op in itself.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Defining a symbol with 'menuconfig' just tells the menuconfig to display
any dependent symbols that immediately follow it in a separate menu.
'menuconfig' has no effect on symbol values.
Making a symbol that doesn't have any dependent symbols after it a
'menuconfig' should be avoided, because then you end up with an empty
menu, which is shown as e.g.
[*] Enable foo ---
This is how it would be shown if there were children but they all
happened to be invisible as well.
With a regular 'config', it turns into
[*] Enable foo
Change all pointless 'menuconfig's to 'config's.
See the section on 'menuconfig' on the Kconfig - Tips and Best Practices
page as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The CONFIG_* prefix was missing, making the #ifdefs always false.
Found with a script (CONFIG_ENS210_CRC_CHECK was unused).
Also make ens210_crc7() static. Guessing it's unused outside this file.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Added in commit 180b139786 ("drivers: sensor: lsm6dsl: Adding sensorhub
support"), then never used.
Found with a script.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
After commit 44f373e806 ("driver/sensor: lis2mdl: make use of STdC
definitions"), the code only looks at LIS2MDL_MAG_ODR_RUNTIME, and not
at the LIS2MDL_MAG_ODR_<frequency> symbols.
LIS2MDL_MAG_ODR_RUNTIME is now a yes/no thing in practice, so remove the
choice and turn it into a regular bool symbol.
Found with a script.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The function that initializes interrupts configures the sensor
register to enable interrupts. It is called before the function that
resets the sensor. Swap the order.
Also correct the mask argument to the configuration command, and use
the BIT() macro to construct the set argument.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Align all sensor drivers that are using stmemsc (STdC) HAL i/f
to new APIs of stmemsc v1.02.
Requires https://github.com/zephyrproject-rtos/hal_st/pull/3
Signed-off-by: Armando Visconti <armando.visconti@st.com>
After switching to new SPI API there is no need to reserve first dummy
byte in buffer and ignore that in application later on. Instead two
buffers can be specified, which is how it is done already in lis2dh
driver. The problem is that dummy byte is still part of the buffer, but
it clearly should no longer be. As an example we write 0x7 (bits to
enable XYZ axes) into CTRL2 instead of CTRL1 register. When reading
measurements on the other hand we have filled buffer starting from 0,
instead of 1 as the driver code has expected.
Fix driver in all places that use burst transfers by removing first
dummy byte from input/output buffer.
Fixes: 2f7e6b6d42 ("drivers/sensors: Switch lis2dh driver to new SPI
API")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
All sensors were using legacy log module registeration method
where LOG_LEVEL was defined before registeration. This method
was error prone as it requires preserving includes order.
Replaced with LOG_MODULE_REGISTER(foo, level).
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Re-run with updated script to convert integer literal delay arguments
to k_thread_create and K_THREAD_DEFINE to use the standard timeout
macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Re-run with updated script to convert integer literal delay arguments to
k_sleep to use the standard timeout macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Reimplementation of clock control driver for nrf platform. It includes
latest API changes: asynchronous starting and getting clock status.
Additionally, it implements calibration algorithm which optionally
skips calibration based on no temperature change. Internal temperature
sensor is used for that.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Use the int_literal_to_timeout Coccinelle script to convert literal
integer arguments for kernel API timeout parameters to the standard
timeout value representations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
LIS2MDL sensor has a fixed sensitivity equal to 1500 uGauss/LSB.
So, use a constant value directly.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Port the lis2mdl sensor driver on top of the lis2mdl_StdC
HAL interface (in modules/hal/st/sensor/stmemsc/).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
