NXP PORT IP instantiations often have different features absent, IE
input buffer, open drain, or slew rate support. Check if the relevant
PCR register bitmasks are defined in the common pin control file, and
define the bitmasks to 0x0 (no effect) if they are not. This allows us
to further consolidate the pinctrl_soc.h headers for SOCs using the PORT
IP.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The FRDM_MCXW71 Platform has a reserved IRQ as its
last IRQ, this test was using this IRQ to
test an interrupt and would not fire. This change
ensures the test does not use the reserved IRQ.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Do not select HAS_SEGGER_RTT unless the segger module is present. This
avoids a Kconfig error when SEGGER's debug module is not present in the
west manifest
Fixes#80529
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
HAS_SEGGER_RTT Kconfix symbol is missing in NXP MCXC series Kconfig.
Add the symbol to fix and enable Segger RTT samples.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Bandgap voltage is used for on die temperature measurement. Bandgap
buffer has to be enabled explicitly to get correct tempearature.
Enable the buffer if TEMP_KINETIS is selected.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Add DT node and clocking of TPM peripherals, which are used for PWM.
Also change the soc clock enable code to not use preprocessor
conditionals.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Base enablement of MCXW merged while z_arm_platform_init was being
deprecated, resulting situation is now that no platform init is
happening, fix by converting to use soc_reset_hook.
Also fix a comment that said the core was being set to 40 MHz, when it
is actually being set up to 96 MHz.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Timer/PWM Module (TPM) initial clock source is not selected.
Add initial clock source selection based on Devicetree configuration.
Rename clock sources definitions from LPUART specific to general names
usable by several modules on the SoC.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Generic hook infrastrucutre was added to Zephyr, but NXP MCXC SoCs
were not updated accordingly.
Use generic hook infrastrucutre for MCXC SoCs.
Signed-off-by: Michal Smola <michal.smola@nxp.com>
Use generic hook infrastrucutre instead of custom Kconfig and hooks for
ARM.
Replace z_arm_platform_init() with platform_reset().
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Include compile of the flash file when FlexSPI_XIP is enabled
even when the FlexSPI driver is not enabled.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
The CONFIG_USB_MCUX_CONTROLLER_TYPE choice config
is not necessary, let's just remove it. Theoretically,
if there was an SOC with the EHCI and LPCIP3511, then
it might cause a build error, but there is no SOC
which is supported on this legacy driver that has that.
Remove all settings of it in the SOC files.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Currently this code related to how to configure the
flash size and address when using flexspi to XIP is copy
pasted in all sort of places and ways all over the tree,
let's clean this up and have single point of control over
this configuration.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Move all dependencies of the family config to series level,
and put a disclaimer saying not to use the family config.
Change all occurrences of the family config in code to the
MCXNX4X series config.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The Kconfig defaults should be in Kconfig.defconfig.
MFD should not be made dependent on the LP flexcomm being
enabled, since MFD can be for other things than just flexcomm.
Change from depends on to an if.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Doesn't seem like there is any reason to be changing the
serial and ADC driver init priorities in the SOC defconfigs.
By default, clock control has priority 30, dma has priority 40,
and serial/adc have priority 50. This seems already to be the order
that is needed, and the original goal of these overrides, which
don't seem necessary anymore.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
- Added a flash runner configuration for rw, mcx, lpc, kinetis and imxrt,
used for sysbuild multi-image projects like MCUBoot.
- Solved the mass erase issue.
- The sysbuild project "west flash --erase" command caused
the mass_erase->flash_img1->reset->mass_erase->
flash_img2->reset sequence.
It was fixed to the mass_erase->flash_img1->
flash_img2->reset sequence.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
- Fix flash_fill() for lpc55 and mcxnx4.
- Set FLASH_FILL_BUFFER_SIZE to the minimal size of data
which can be written to a device (by default is only 32).
- Fix the [flash_map.test_flash_area_erase_and_flatten]
failed test of tests/subsys/storage/flash_map.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
LPFlexcomm is a MFD device hence select this Kconfig whenever
it is enabled.
Remove the selection from the individual driver Kconfig files.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
