Introduce etrbuffer in the tddconf bindings to support flexible
placement in the memory map.
Signed-off-by: Karsten Koenig <karsten.koenig@nordicsemi.no>
This commit adds the pfic interrupt controller driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds the usart driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds the systick driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds the clock driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds the pinctrl driver for WCH CH32V003.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
This commit adds the dtsi and bindings for the WCH CH32V003 which is a
32-bit general-purpose RISC-V MCU.
Signed-off-by: Michael Hope <michaelh@juju.nz>
Signed-off-by: Dhiru Kholia <dhiru.kholia@gmail.com>
- Add SPI driver support for RA
- RA2A1 not support slave select keeping level so disable it
in Kconfig
Signed-off-by: Tri Nguyen <tri.nguyen.wj@bp.renesas.com>
Signed-off-by: Thao Luong <thao.luong.uw@renesas.com>
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Use a string for the mipi-mode property over an integer value, as this
significantly improves the readability of the MIPI DBI device binding.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The NXP LCDIC peripheral contains two internal timers, with configurable
periods. These times are used to determine delays within the peripheral,
such as the reset and tearing enable signal delays. Allow these periods
to be set within the devicetree for the peripheral.
Raise the period where required for display drivers that need a value
other than the reset setting
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Extend tca954x (tca9546a, tca9548a) driver to support tca9544a i2c MUX.
(different bitmask and flag for enable bit in register)
Signed-off-by: Florian Weber <Florian.Weber@live.de>
The NXP PORT pinmuxing peripheral is reused across the MCX, S32, and
Kinetis lines. Rename the compatible from the family-specific
nxp,kinetis-pinctrl to a more generic nxp,port-pinctrl to reflect the
actual name for the IP block used within reference manuals.
Update the NXP HAL revision to include a change to use the new Kconfig
name for the PORT pinctrl driver
Update the MAINTAINERS.yml path, as there are no longer any NXP drivers
matching the string "drivers/*/*kinetis*
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Replace the DT_INST_PROP_OR statements with defaults
in the devicetree binding of the iCE40.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Remove the renesas,ra-clock-generation-circuit driver, which is no longer
needed after migrating to the FSP-based implementation.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Remove the renesas,ra-pinctrl driver, which is no longer
needed after migrating to the FSP-based implementation.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
A few bindings in the timer directory (for kernel timing sources) were
being used for counters (which can have alarms set, and have a distinct
API). Move these bindings to the counters directory.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Added a binding description for the PPIB peripheral and added the device
tree nodes of the PPIB instances to the nRF54L15 and nRF54L20.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Convert the numerous revision compatibles to a DT property for the
revision called nxp,version (inspired from a linux DT property from
st called st,version on their DMA).
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
The Xilinx AXI DMA Controller is commonly used in FPGA designs.
For example, it is a part of the 1G/2.5G AXI Ethernet subsystem.
This patch adds a driver for the Xilinx AXI DMA that supports
single MM2S and S2MM channels as well as the control and status
streams used by the AXI Ethernet subsystem.
Signed-off-by: Eric Ackermann <eric.ackermann@cispa.de>
some flashes support special opcodes
for 4-byte addressing, that can be used
without switching to 4-byte mode.
Signed-off-by: Fin Maaß <f.maass@vogl-electronic.com>
Implement a new stable-poll-period-ms property to specify a new (slower)
polling rate for when the matrix is stable.
The keyboard thread can eat up a surprisingly high amount of cpu cycles in
busy waiting if the specific hardware implementation happen to have a
particularly slow settle time, but high frequency polling is really only
needed when debouncing.
The new property allow slowing down the polling rate when the matrix is
stable (either key pressed but none to be debounced or idle in the case
of the gpio implementation with no interrupts), this allows reducing the
overall cpu time taken by the keyboard scanning thread when keys are
persistently pressed.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The it8xxx2_kbd KSO pins can be used as both keyboard scan and GPIO. By
default the keyboard scanning driver controls the output level of all
the KSO signals from 0 to (col-size - 1), meaning that any line in
between used as GPIO is going to have its output value overridden.
Add a kso-ignore-mask property to the keyboard scan driver to allow
specifiying extra pins that should not be controlled by the driver.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
This follows update of UTCPD.VBSCALE register field. It supports:
- "divide-20": External VBUS voltage divider circuit should be 1/20
for EPR application. The divided voltage compares with
200mV to set or clean VBUS Present bit.
- "divide-10": External VBUS voltage divider circuit should be 1/10
for SPR application. The divided voltage compares with
400mV to set or clean VBUS Present bit.
Signed-off-by: Chun-Chieh Li <ccli8@nuvoton.com>
Add a driver for the MB85RSM1T FRAM chip.
Signed-off-by: Jakub Wasilewski <jwasilewski@internships.antmicro.com>
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
The HAL configuration binding can be done dynamically based on the
IP's address space. The `hal-cfg-index` property is more tied to
software rather than hardware so remove it as an attempt to clean
up the binding.
Signed-off-by: Laurentiu Mihalcea <laurentiu.mihalcea@nxp.com>
Add npcm miscellaneous device control and power and clock control
instances.
Add device tree bindings for npcm power and clock control.
Signed-off-by: Alan Yang <tyang1@nuvoton.com>
Add initial support of the mailbox driver based
on the inter VM shared memory mechanism similar
as the existing IPM driver.
Signed-off-by: Felipe Neves <ryukokki.felipe@gmail.com>
With this change, the LPTIM counter will be able to set
its timeout to the st,timeout value. So that system can
sleep for that period without interruption.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Replace the enum for load modes for the iCE40 with a boolean flag,
as there are only two options:
- SPI: default, which should be used whenever possible
- GPIO bitbang: workarorund, in case a low-end microcontroller is used
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
-Update formatting and contents of index.rst for cy8ckit_062s4
-Update formatting and contents of index.rst for cy8ckit_064s0s2_4343w
-Update formatting and contents of index.rst for cy8cproto_062_4343w
-Update formatting and contents of index.rst for cy8cproto_063_ble
-Update formatting and contents of index.rst for xmc45_relax_kit
-Update formatting and contents of index.rst for xmc47_relax_kit
-Change all instances of "PSoC" to "PSOC" for infineon platforms
Signed-off-by: McAtee Maxwell <maxwell.mcatee@infineon.com>
This bus type was originally created for what's today the ipc.c HCI driver.
Since this type hasn't yet been synced with BlueZ, rename it for
consistency, however leave the old define to not break backwards
compatibility with existing DT bindings (there are several more that use
"ipm" than ipc.c).
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
The authoritative source of these values is BlueZ:
https://git.kernel.org/pub/scm/bluetooth/bluez.git/tree/lib/hci.h#n38
Update our values with the above. The IPM definiton doesn't exist in
BlueZ, but should be added there to make sure we don't get out of sync
again.
Signed-off-by: Johan Hedberg <johan.hedberg@silabs.com>
Remove CONFIG_MMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the mmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
mmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Remove CONFIG_SDMMC_VOLUME_NAME, and set the disk name based on the
``disk-name`` property. This aligns with other disk drivers, and allows
for multiple instances of the sdmmc_subsys disk driver to be registered.
Add disk-name properties for all in tree definitions for the
sdmmc-subsys disk driver, and change all in tree usage of the disk name
Fixes#75004
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
The new update of clock device tree make the pll p q r clock
source cannot be choose by other node
This fix add 1 new dts binding for pll out p q r out line
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
