Add a timeout to the `bme280_wait_until_ready` loop to ensure that we
never get stuck in this loop even if the bus enters an error condition.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Add support for Bosch bmp390 sensor, the drop in replacement for the
bmp388 with same register but different chip-id. This patch make use
of "bosch_bmp390" or "bosch_bmp388" and set the specific chip-id in a
data->chip-id variable, which then used to check against the register
value.
Additional, manual shift operation had been replaced with ENDIAN safe
macros and calibration values with target variable of int16_t add a
cast for it.
bmp388_spi: read register implementation wrong, fixed it.
tx-buffer must be <addr><dummy><dummy> in order to receive the
register value. Read registers in burst mode and have rx and tx
buffer same spi_buf to avoid clock stop and delay with nrf5.
Signed-off-by: Chris Ruehl <chris@gtsys.com.hk>
Inform the executor of a submissions completion with -ENOMEM
if the size of the workq is not big enough.
Signed-off-by: Florian Weber <Florian.Weber@live.de>
Support the BMM150 being on a power domain, which may not be powered at
boot. For example, Nordic Thingy53.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Update power management to only start/stop periodic measurements in
`CONFIG_BME280_MODE_NORMAL`, instead of re-initialising the chip
completely.
In `CONFIG_BME280_MODE_FORCED`, there is nothing to do when suspending,
as the sensor is already in its lowest power mode.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Add missing braces to comply with MISRA C:2012 Rule 15.6 and
also following Zephyr's style guideline.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
Only read the compensation parameters from the chip on first power up,
as they are static on the device.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Support the BME680 being on a power domain, which may not be powered at
boot. For example, Nordic Thingy53.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Add driver support for Bosch bmp180 pressure sensor running on i2c bus.
It pushes the driver files to the bmp180 directory under
drivers/sensor/bosch. The driver implement the Sensor API
and support channel DIE_TEMP and PRESSURE.
Driver had been tested with the NRF5340DK.
V2 fixup
---------
Drivers: Bosch bmp180 fixups for PR v2
fix BMP180 in CMakeLists.txt
rename regControl to ctrlreg
simplify the logic in set_attribute
use BMP180_GET_CMD_TEMP_DELAY
Drivers: Bosch bmp180 use system byteorder macros
To aware of ENDIANESS use the macros from byteorders.h
Drivers: Bosch bmp180 comments added to #endif
Add a comment to the #endif /* CONFIG_FOO */
Drivers: Bosch bmp180 , fix twister run error
twister report an error related to using floor() with a float
fix this using floorf() function.
Drivers: Bosch bmp180, rework review v2
fix code style issues
simplify the structure for bus and i2c.
prepare to remove the empty bmp180_i2c.c
Drivers: Bosch bmp180, remove bmp180_i2c.c
bmp180: update CMakeList.txt remove bmp180_i2c.c
bmp180: remove unused variable
fixups for complient checks
replace homebrew bitshift with byteorder.h macro
sys_get_be16 and sys_get_be24
cleanup remove unused spi.h
change struct reg16/24 to uint8_t[]
remove channel AMBIENT_TEMP
bmp180/Kconfig add missing help text
fix indent issue in bmp180_pm_action
merge BMP180_CONFIG_I2C into BMP180_INST
Move DT_DRV_COMPAT out of the header file
drop LOG_DBG() from read calibration data
remove bus_io implementation and header cleanup
move headers and structs out from bmp180.h
fix typo in comment
apply clang format changes, only if not line lenght violation
fix indent code error after joined lines
conversion from Pa to kPh was wrong, fixed it
Remove default=n from Kconfig, it is the default.
Move the conversion ready test into a function (duplicate code)
and apply retry policy
parameter naming with indicate the usage
change BMP180_INST(inst) to clang format
fix int32_t overflow in convension formular
fix wrong devider in convension formula
move BSWAP_s16 BSWAP_u16 from .h to .c
Signed-off-by: Chris Ruehl <chris@gtsys.com.hk>
Some functions in the bmm150 driver were depending on a define
that was never used. Changed it to the one that is actually defined.
Signed-off-by: Maximilian Deubel <maximilian.deubel@nordicsemi.no>
The integer return of sensor_submit should be void as the call is
asynchronous and the response is meant to be delivered using RTIO APIs
signaling that the submission completed with error or success.
Change the function signature to void and fix all uses of the submit
API, fixing some bugs in the process.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
Read less data from the sensor and use standard zephyr functions for
extracting integers from byte arrays.
Signed-off-by: Jordan Yates <jordan@embeint.com>
`sensor_sample_fetch` is documented to read all of a sensor's active
channels and block until complete. The previous implementation read
the result from the previous call and triggered the next sample.
As a result the first call always failed, and subsequent calls would
return data one sampling period old.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Use a structured channel specifier rather than a single enum when
specifying channels to read in the new read/decoder API.
Replaces usages of a seperate channel and channel_index parameter
where previously used with a struct sensor_chan_spec.
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
