Define the configuration through an overlay file
to run the sample on the nucleo_h743zi target board.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
On the stm32l073rz nucleo and stm32f091rc nucleo
boards, the DTS pwm-leds node is disabled, because
the output pin might conflict with SPI1.
It is necessary to enable the node in the overlay
to compile and run the sample.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
integration platforms can't be filtered out, adapt tests so that those
platforms are always available for testing.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The overlay for the nRF52840 DK board uses ADC controller child nodes
for specifying channel configurations and it shows how to configure
a channel in differential input mode, so it can serve as an example
of how to use these new possibilities. The overlay for the nRF51 DK
board shows how to use a specific ADC resolution (the default 12 bit
setting is not supported by nRF51 SoCs).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Allow specifying configuration of channels through child nodes of ADC
controllers. This way analog inputs can be specified for channels in
SoCs that require this and it is also possible, for example, to use
different gain or reference selections for particular channels.
This commit also removes a few former limitations of the sample: now
it is possible to use more than 2 channels and each channel can use
a different ADC controller. Also the ADC resolution to be used can be
specified through devicetree.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This add a new sample application to test and validate
the stm32 octospi driver on the NOR octo-flash present on
stm32 disco kits
There should be a special case to erase the complete flash.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Increase the heap size for RT1170 EVK to allocate the
display buffers for a 720x1280 display
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Convert the can_mode enum to a bit field to prepare for future extensions
(CAN-FD mode, transmitter delay compensation, one-shot mode, 3-samples
mode, ...).
Rename the existing modes:
- CAN_NORMAL_MODE -> CAN_MODE_NORMAL
- CAN_SILENT_MODE -> CAN_MODE_LISTENONLY
- CAN_LOOPBACK_MODE -> CAN_MODE_LOOPBACK
These mode names align with the Linux naming for CAN control modes.
The old CAN_SILENT_LOOPBACK_MODE can be set with the bitmask
(CAN_MODE_LISTENONLY | CAN_MODE_LOOPBACK).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
LCD display is connected to the I2C bus SoC bus in the development kit,
this sample guides the user on how to use the LCD display with I2C commands
Signed-off-by: Esteban Valverde <esteban.valverde.vega@intel.com>
Add pinmux settings for lpadc to LPCXpresso55s69 and LPCXpresso55s28
boards. Enable ADC driver sample for LPCXpresso55s69, to aid in testing
pinmux settings.
Fixes#45401
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
In order to bring consistency in-tree, migrate all samples to the use
the new prefix <zephyr/...>. Note that the conversion has been scripted:
```python
from pathlib import Path
import re
EXTENSIONS = ("c", "h", "cpp", "rst")
for p in Path(".").glob("samples/**/*"):
if not p.is_file() or p.suffix and p.suffix[1:] not in EXTENSIONS:
continue
content = ""
with open(p) as f:
for line in f:
m = re.match(r"^(.*)#include <(.*)>(.*)$", line)
if (m and
not m.group(2).startswith("zephyr/") and
(Path(".") / "include" / "zephyr" / m.group(2)).exists()):
content += (
m.group(1) +
"#include <zephyr/" + m.group(2) +">" +
m.group(3) + "\n"
)
else:
content += line
with open(p, "w") as f:
f.write(content)
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Fix usage of integration_platforms. Do not set it when the board is
excluded using some other filters.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
For consistency with the scheme used for other nRF peripherals,
use the peripheral name that nRF Product Specifications use.
In this case, it is WDT, not WATCHDOG.
Also remove the requirement for the label property in the binding.
It is no longer needed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This is a follow-up to commit cf6a58d3f6.
Restore the "nordic,nrf-ipc" compatible property in mbox nodes for both
nRF5340 cores and use it together with the new "nordic,mbox-nrf-ipc"
one. This way either the MBOX or the IPM driver can be used for these
nodes without further modifications. This eliminates the need to use
overlays in quite a few cases, so remove all those no longer needed
ones (which are also a bit confusing now as they refer to no longer
existing ipc@2a000 and ipc@41012000 nodes).
Restore also the ipc node label removed in the commit mentioned above,
as the label is used in validation of base addresses of nRF DT nodes.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The optional flash device can be obtained at compile time using
DEVICE_DT_GET_OR_NULL. Init code has been adjusted so that flash_dev is
forced to NULL when device is not ready (user can later specify the
device manually).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This update Atmel sam0 serial drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This update Atmel sam afec driver to use pinctrl driver and API. It
updates all boards with new pinctrl groups format. In addition, it
add overlay files to allow run samples/drivers/adc example.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This commit adds support for the Arduino Nicla Sense ME board.
The board functionality has been tested using the samples:
- hello_world
- philosophers
- peripheral_dis
- spi_flash
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
Include a pointer to the CAN controller device for the CAN
transmit, receive, and state change callback functions.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The overlay are defined to run the samples application with PWM
feature on the nucleo_l073rz,nucleo_f091rc, nucleo_g474re
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Kconfig options now belong to the Kconfig domain, therefore, the
:kconfig:option: role needs to be used.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This file defines the crypto driver API, cipher is supposed to be just
one type of capability (other can be hash) of these drivers, just
change the file name to be consistent with it.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add a couple of extra shield configurations to catch regressions with
the st7735r, gd7965 and ls0xx drivers.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
- Filter out the remaining CAN tests if no zephyr,canbus chosen node is
enabled in the devicetree.
- Rename the tests to shorten the name a bit.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The driver was never migrated to Devicetree, this patch converts the
driver to a proper Devicetree based device.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The driver does not implement a display API, it has a custom API. Having
it under display is confusing, since display API consumers may expect
they can use it. These sort of custom drivers fit better under
drivers/misc.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add a basic device tree overlay to support the use of the ATSAMD21 XPro
dev board with the ADC sample application.
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
All drivers that require input_positive to be set should be given it.
Some parts may require an offset, so abstract this away too.
Signed-off-by: Attie Grande <attie.grande@argentum-systems.co.uk>
Lora samples are missing harnesses and hence are reported
failed by default by twister.
Add required harnesses to be able to detect correct and faulty
test executions.
Fixes#42159
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The CAN_BUS_UNKNOWN CAN controller state is only used to indicate that
the current CAN controller state could not be read.
Remove it and change the signature of the can_get_state() API function
to return an integer indicating success or failure.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
