Enable pull-up on UART TX pin to reduce power consumption.
If the board is powered by battery the SoC consumes more
power than expected.
The consumption increases because TX pin is floating
(High-Impedance state of pin B from Dual-Supply Bus Transceiver).
Similar to commit b5b728495b
("boards: reel_board: enable pull-up on UART RX pin")
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
I2C support has been added back into the up_squared, leveraging the
new PCIe support in the DesignWare I2C driver.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The legacy PCI support in the DesignWare I2C driver is replaced with
the new PCIe support. The Intel Quark X1000 SoC and the galileo board
configurations are updated accordingly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The SBL configuration no longer differs in any detail (except its name)
from the "standard" UpSquared configuration, so it is removed.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This needs to be pushed down to the SoC level, as it's an Apollo Lake
feature, not a feature of the UpSquared. Remove the Apollo Lake
references to the PCI devices because these will not be used when I2C
support is restored.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This option is no longer used in the dts_fixup.h file since there
are no SBL-specific fixups.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The second serial port (UART_1) can be used for connecting to
host serial port. This is used for example by PPP (Point-to-Point
Protocol) implementation in which case the pppd running in Linux host
connects to a pty that is linked to UART_1 in Zephyr.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The Particle.io Boron is an nRF52840-based board with a connected
u-blox SARA-R4 modem. The main board was previously upstreamed
without modem support.
Now that we have a driver to support the SARA-R4 modem, let's enable
it for the Boron board.
Signed-off-by: Michael Scott <mike@foundries.io>
SparkFun offers an Arduino-R3 compatible shield using the SARA-R410M-02B
LTE Cat M1/NB-IoT modem.
Now, that the basic SARA-R4 modem driver is implemented, let's enable
the shield for several MCUs supporting Arduino-R3 compatible headers.
Product Link:
https://www.sparkfun.com/products/14997
Signed-off-by: Michael Scott <mike@foundries.io>
Let's change the specific WNC-M14A2A check into a more generic
MODEM check for enabling ethernet. Many of these pins are used
on the Arduino headers.
Signed-off-by: Michael Scott <mike@foundries.io>
This shield uses a non-standard UART exposed via Arduino-R3
compatible header pins.
It has configurations for FRDM_K64F and nRF52840_PCA10056.
Signed-off-by: Michael Scott <mike@foundries.io>
This commit adds a DTS node for the ARM MPU peripheral in the
device tree of ARMv8-M SoCs (for the secure and the non-secure
DTS descriptions) and updates the fixup files. SoCs:
- nrf9160
- musca_a
- musca_b1
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The ACRN board configuration is not suitable for production use,
but many people are mistakenly using it as a starting point for
real-time applications. I've added a note to clarify.
Signed-off-by: Charles Youse <charles.youse@intel.com>
MHU (Message Handling Unit) enables software to raise interrupts to
the processor cores. It is enabled in SSE 200 subsystems.
This patch aims to implement inter processor communication.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Add support for the NXP TWR-KE18F development board. This board
feautures an NXP MKE18F16 MCU, a selection of user LEDs and
push-buttons, potentiometer, thermistor, CAN interface, and FlexIO
header.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The mikroe_mini_m4_for_stm32 board is developed by Mikroelektronika
not by STMicroelectronics.
Also use more appropriate "mini-m4-for-stm32" board name for
compatible dt property.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Enable the counter capability in the board and add a .conf file for the
nRF52810 running on the PCA10040 board.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The supported field is used by sanitycheck to select which tests will be
run on a particular board. The issue with the counter drivers, and in
particular on nRF ICs, is that the timer peripherals are disabled by
default and need to be enabled on a per-board basis inside a .conf file.
Since this board doesn't have a .conf file in
tests/drivers/counter/counter_basic_api/boards/ the test cannot be run
on this board.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit adds support for board: nrf52811_PCA10056.
The nRF52840 DK: PCA10056 is the recommend development kit, it emulates
the nRF52811, and can be used as a starting point for development
before moving over to a custom board.
Please note that this development kit does not support Bluetooth
Direction Finding. What is more it cannot be used with most of Arduino
shields because of PCA10056 PIN layout.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Increase ram size as flash simulator need it for
emulated storage. The qemu_x86 flash size is puted back to
its original value of 4092K
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
This commit adds J-Link runner for efr32_slwstk6061a board. To use it
it is necessary to install J-Link Software and Documentation Pack.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This commit enables internal SoC DC-DC converter on efr32_slwstk6061a
board.
RF components on efr32_slwstk6061a board are connected to the internal
SoC DC-DC converter. Upon startup the DC-DC converter is configured in
the bypass mode. Such configuration provides enough power for the SoC to
boot and perform basic operation. It is not enough however to operate
the radio subsystem. Without this patch enabling radio in Rx or Tx mode
causes voltage drop and triggers brown out detector reset.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
