Added HAL Radio abstractions to use SoC specific Radio Timings
as documented in SoC's electrical characteristics.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
An OCF is a 10-bit value as defined by HCI, and therefore requires a
16-bit integer to store it.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Fixed assert due to incorrect implementation of stopping of
advertiser role under directed advertisement timeout, and
also, fixed assert due to adv stop ticker not being stopped
on advertisement disable from thread mode.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added checks for advertiser and initiator/target addresses
received in CONNECT_IND when performing directed
advertising.
This is required to pass TP/CON/ADV/BV-04-C [Directed
Advertising Connection].
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When directed advertisements timed out, connection context
associated was not being released. Subsequent connectable
advertising or connection creation failed.
This is now fixed by releasing the connection context on
directed advertisement timeout.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Refactor whitelist handling into generic filter management in
preparation for future resolving list ID address filters.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This initial commit adds the following:
* Handling of privacy HCI commands
* New Link Layer filter module for both whitelist and resolving list
* Advertising RPA generation with timeouts
Follow-up commits will expand the functionality.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
For consistency with the return value and to conform with other naming
schemes, rename mem_is_zero() to mem_nz().
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use globally available find_lsb_set in Zephyr instead of a
custom find first set function.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In preparation towards Privacy 1.2, move implementation that
swapped scan response PDU double buffer to same place as
where adv data PDU double buffer is swapped. So that, change
in AdvA in adv data PDU can be reflected in scan response
PDU buffer.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added fix to avoid adv data set function call from
corrupting a ADV_EXT_IND PDU under LE Extended Advertising.
Also, avoid redundant code execution under directed
advertising.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Only ADV_IND, ADV_DIRECT_IND, and CONNECT_IND PDUs can have
ChSel bit set in Advertising channel.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added a callback function ll_adv_scan_state_cb from the
Controller that gets called on either an advertiser or a
scanner getting started as the Controller's first enabled
state. The callback is also called on the Controller's
last disabled advertising or scanning state.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix missing implementation to reset the advertiser state
when directed advertisements stop without a connection being
established.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In order to reuse code, the reset() function is used both to handle the
reset HCI command but also to initialize the internal HCI variables when
bringing up the system. In the latter case, avoid setting the reset bit
in the state atomic and signalling the polling API, since that is not
required during initialization.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As a preparation for advanced filtering (Controller-based privacy) this
commit refactors whitelisting so that it becomes its own module and
actually correctly performs state tracking to avoid modifying the
whitelist when it's in use.
Additionally it also removes the duplicate separate entries for
advertising and scanning, since the specification only allows one single
global whitelist singleton.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add internal functions to read advertiser and scanner filter
policy if the roles are enabled. This is required to
restrict updates to whitelist and resolving lists when
filter policy are being used by the roles.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Under invalid host behavior, trying to start advertising
while already active would corrupt the advertiser context.
This is fixed by having an explicit flag to check whether
advertiser is already running.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Under invalid host behavior, trying to start scanning while
already active would corrupt the scanner context. This is
fixed by having an explicit flag to check whether scanner is
already running.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Restrict encryption support on nRF51 series SoC to Bluetooth
LE 1M PHY and max. 27 bytes PDU. If 251 bytes PDU using Data
Length Update procedure is desired, then LE Encryption
procedure will not be supported (until a software CCM is
implemented in future).
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add Kconfig option to be able to conditional compile the
Bluetooth v4.0 LE Encryption procedure.
This is needed in order to be able to not support encryption
on nRF51 series when using Data Length Update procedure with
upto 251 byte payloads until a software-based CCM support is
implemented.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
While returning 32-bit values from radio status interfaces,
explicitly compare radio h/w event registers to be non-zero,
dont just return the direct 32-bit h/w register content.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Added extra assert checks to detect controller failure if
a role event preparation function was not followed by the
role event start function.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
In commit c41d3edda when implementing the alternative
encryption setup implementation, the original fast
encryption setup implementation was broken. When host is
slow in responding to LTK request, the controller asserted
when fast encryption implementation is selected. This is
now fixed.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Fix the assert in the controller during connection setup
when peer does not support CSA#2 feature and free Rx buffer
queue does not have enough buffers to generate CSA event.
The assert was reproduced by turning on advertisement
indication and scan request notification features in the
controllers advanced features, and a peer that does not
support CSA#2 initiated a connection.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Since role support is fundamental to both the Host and the Controller,
move the role configuration options to the top-level file and rename
them to fit the GAP specification, avoiding confusion between GAP and LL
names.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Only include connection-related options when CONFIG_BLUETOOTH_CONN is
selected, since otherwise this can lead to inconsistencies between
features and supported commands.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Due to several changes in the way stacks are calculated, 320 bytes is no
longer enough for the controller-only build. After measuring usages of
up to 320 bytes (locally) and 376 (reported by Ricardo Salveti), the
stack size is increased by 128 bytes, up to 448 bytes.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Added implementation to handle an incoming Reject Ext Ind PDU in
response to a sent Length Req PDU.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
When initiating Data Length Change at the same instant the
crossover condition was not handled correctly causing the
controller to assert.
This fix will allow crossover of Data Length Update
procedure, and this collison is harmless as per Bluetooth
specification, and gracefully handled by the controller.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Return error codes for HCI Tx buffer overflow conditions are
missing which would lead to silent dropping of Tx packets if
host implementations do not follow number of completed packets
or use correct buffer counts as returned by HCI Read Buffer
Size command.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
With the support for 2M PHY added, the controller can now Rx/Tx
upto 18/19 minimum sized L2CAP packets per 7.5ms connection
intervals.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
To allow for hci_uart builds that do not include the controller code,
move the UART Kconfig option used by the sample up one level so that it
is shared by all configurations using Bluetooth:
Jira: ZEP-2132
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since more and more code is going to be reused by both the Host and the
Controller, this commit introduces a common/ folder that will contain
everything that is not tied to one of the two components but shared by
them.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This reverts commit 698de88916 ("Bluetooth: controller:
Cleanup redundant ticker busy loop")
Scan enable asserted in ctrl.c line 3756 due to the fact that a
role event was active and ticker job has hence been disabled.
Add back the busy loop so that scan enable can wait until the
active role event completes gracefully.
The ticker busy loop is mandatory in all ticker interface calls
if a blocking behavior is desired.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The calculation in packet_rx_reserve_get() was already handled by
packet_rx_acquired_count_get(). So, let's use that code instead
and remove the duplication.
Change-Id: Ic76f70f1e78bebc74f5bef36cd92a3c332e489e9
Signed-off-by: Michael Scott <michael.scott@linaro.org>
This calculation can be used in packet_rx_reserve_get() where currently
the code is duplicated from packet_rx_acquired_count_get().
Let's allow use of packet_rx_acquired_count_get() regardless of whether
CONFIG_BLUETOOTH_CONTROLLER_DATA_LENGTH is enabled.
Change-Id: I613bde0a407f3caccabb22f369098575965e98ad
Signed-off-by: Michael Scott <michael.scott@linaro.org>
During testing, lr->max_rx_octets and lr->max_tx_octets were
at times set to 0. If we use these 0 values, we end up with
very erratic behavior. Best, to check for a sane value and
if invalid, default to the value in _radio.conn_curr->max_*x_octets.
Change-Id: I57c0e3790d988f0de17993cebe5c5c2ab0fc07a6
Signed-off-by: Michael Scott <michael.scott@linaro.org>
When Controller to Host flow control is enabled, output informational
messages for certain operations to help tune and debug the feature.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
