Instead of always allocating both IPv6 and IPv4 address information
to every network interface, allow more fine grained address
configuration. So it is possible to have IPv6 or IPv4 only network
interfaces.
This commit introduces two new config options:
CONFIG_NET_IF_MAX_IPV4_COUNT and CONFIG_NET_IF_MAX_IPV6_COUNT
which tell how many IP address information structs are allocated
statically. At runtime when network interface is setup, it is then
possible to attach this IP address info struct to a specific
network interface. This can save considerable amount of memory
as the IP address information struct can be quite large (depends
on how many IP addresses user configures in the system).
Note that the value of CONFIG_NET_IF_MAX_IPV4_COUNT and
CONFIG_NET_IF_MAX_IPV6_COUNT should reflect the estimated number of
network interfaces in the system. So if if CONFIG_NET_IF_MAX_IPV6_COUNT
is set to 1 and there are two network interfaces that need IPv6
addresses, then the system will not be able to setup IPv6 addresses to
the second network interface in this case. This scenario might be
just fine if the second network interface is IPv4 only. The net_if.c
will print a warning during startup if mismatch about the counts and
the actual number of network interface is detected.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Move IP address settings from net_if to separate structs.
This is needed for VLAN support.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Create infrastructure that allows ethernet device driver to tell
if it supports network packet checksum offloading. This applies only
to IPv4, UDP or TCP checksums. The driver can enable/disable checksum
offloading separately for Tx and Rx network packets.
If the device (ethernet in this case) can calculate the network
packet checksum for IPv4, UDP or TCP, then do not calculate the
corresponding checksum by the stack itself.
Fixes#2987
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add freeaddrinfo() to complement getaddrinfo().
Existing applications using getaddrinfo() will usually free
allocated memory using freeaddrinfo(). Even if nothing is allocated
the function should exist to avoid having to change the application
when porting.
Signed-off-by: Stig Bjørlykke <stig.bjorlykke@nordicsemi.no>
Avoid listing internal function in the public API documentation. After
enabling those doxygen configs, we go lots of errors and bad refs that
were fixed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
If CONFIG_NET_DEBUG_NET_PKT was enabled, then a call to
net_pkt_get_reserve_data() was calling wrong debug function
which caused compile error.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add support for MSG_PEEK flag in recv and recvfrom.
This flag is needed when using non-zephyr embedded applications with
Zephyr's socket API.
Signed-off-by: Stig Bjørlykke <stig.bjorlykke@nordicsemi.no>
As following commits need this functionality, create a function
which converts "01:02:ab:fe:34:dd" type hex strings to array of
bytes. Change the SLIP driver to use this new function.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add support for MSG_DONTWAIT flag in recv and recvfrom.
This flag is needed when using non-zephyr embedded applications with
Zephyr's socket API.
Signed-off-by: Stig Bjørlykke <stig.bjorlykke@nordicsemi.no>
Since this function is used on some drivers, and knowing these drivers
can be built for OpenThread, let's make it generic and out of the
802.15.4 L2 stack.
Fixes#5942
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add console driver that allows console session to be transferred
over a websocket connection.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit creates a websocket library that can be used by
applications. The websocket library implements currently only
server role and it uses services provided by net-app API.
The library supports TLS if enabled in configuration file.
This also adds websocket calls to HTTP app server if websocket
connection is established.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
net_app_ctx maintains multiple net contexts(net_ctx). But when http
api's wants to reply or send some data, its always choose the first
net_context in the array, which is not correct always.
net_app_get_net_pkt_with_dst() api will select proper context
based on destination address. So with the help of new api in
net_app, http can select proper context and send packets. To
achieve this, desination address is provided in http_recv_cb_t
and http_connect_cb_t callbacks. Also chaged relevant API's to
provide destination address in http message preparation methods.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
It's added in subsys/net/lib/http/http_client.c:http_request():95
after adding the protocol header. If we add 2 CRLF it ends the
header block and causes an HTTP error.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Static variables that don't strictly need to be initialized at
boottime should be declared with __noinit. This makes a considerable
difference especially for large buffers.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Difference being that the data is not, then, allocated from the pool.
Only the net_buf is.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Make it safe to call net_buf_simple_init() even if the buffer was
created using the new macros. This is possible to detect since with
the new macros buf->__buf will be non-NULL and with the old
NET_BUF_SIMPLE() macro it will be NULL.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Introduce two new "standard" data allocators to net_buf. There are now
three in total:
NET_BUF_POOL_FIXED_DEFINE: This is the closes to the old
implementation, i.e. fixed size chunks. It's also what the old
NET_BUF_POOL_DEFINE macro maps to.
NET_BUF_POOL_HEAP_DEFINE: uses the OS heap
NET_BUF_POOL_VAR_DEFINE: defines a variable sized allocator using
k_mem_pool (this is all that there was in my first draft of this
feature)
Currently the variable length allocators (HEAP & VAR) support
reference counted data payloads, i.e. cheap cloning. The FIXED
allocator does not currentlty support this to allow for the simplest
possible implementation, but the support can be added later if
desired.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Redesign of the net_buf_simple and net_buf structs, where the data
payload portion is split to a separately allocated chunk of memory. In
practice this means that buf->__buf becomes a pointer from having just
been a marker (empty array) for where the payload begins right after
the meta-data.
Fixes#3283
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Added a new API to get net pkt based on dst address. Destination
address will be used to find correct net_context.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Provided separate event information structs based on events. This way
user will know what kind of information will be received to that
particular event.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Introduce CONFIG_NET_ROUTING option that allows the IP stack
to route IPv6 packets between multiple network interfaces.
No support for IPv4 routing is implemented by this commit.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Previously, POSIX function names were aliased to zsock_ function
names using, for example:
#define connect zsock_connect
This caused the C preprocessor to replace any symbol named 'connect',
whether a function or not, in all source code which included socket.h,
with 'zsock_connect'. This generated unintended code where the symbol
'connect' was used as the name of a structure field (as in mqtt.h).
This new inline definition is applied to all the POSIX function symbols,
with the exception of fcntl, a redefinition of which would conflict
with the definiton in the toolchain's fcntl.h.
Fixes#5817
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Use CONFIG_IEEE802154 instead of CONFIG_NET_L2_IEEE802154
and CONFIG_IEEE802154_RAW_MODE when adding RSSI and LQI
members to net_pkt. CONFIG_IEEE802154 is selected when
at least one 15.4 device is selected (L2 or RAW).
Signed-off-by: Kamil Sroka <kamil.sroka@nordicsemi.no>
The meaning of this address type is the same as NET_ADDR_MANUAL,
but with a provision that DHCP can override such an address.
It's intended for the usecase when there's a default static
configuration for when DHCP is not available, but DHCP should
override it.
Before going to add another address type, there was an attempt
to repurpose TENTATIVE address state, but it doesn't work as
expected, as indeed, all existing address types/states already
have clearly semantics, and it makes sense to just another
address type to avoid confusion and unexpected behavior.
Fixes: #5696
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
In some cases, we need to initialize DNS servers from a binary
addresses, e.g. in case of DHCP processing. With existing API,
such addresses would need to be converted to strings, just to
be converted back to struct sockaddr in dns_resolve_init().
This is not efficient, and with a number of addresses quite
cumbersome. So instead, allow to pass DNS server either as
strings, or as struct sockaddr's (or both).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The offset of the IP header in a received packet depends on the L2
header size. For Ethernet this is 14 bytes which puts the u32 IPv4
addresses on a non-u32 byte boundary. This causes chips that don't
support unaligned access (like the Cortex-M0) to fault.
The fixes in this patch are enough to ping the board and run the
http_server sample.
Signed-off-by: Michael Hope <mlhx@google.com>
It will be up to the user to configure a valid channel, through
net_mgmt, and call net_if_up() in order to get the device up.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Sub-Ghz bands have different limit of channels. 10, or more than a
thousand is actually possible. Thus the device needs to expose such
limit to the L2 which is unaware of frequency band logic. L2 will
then allow user to select a proper channel.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix build break when enabling CONFIG_HTTPS w/o CONFIG_NET_APP_SERVER
This error can be seen when building sample/net/http_client like so:
$ cd samples/net/http_client
$ mkdir build && cd build
$ cmake -DBOARD=qemu_x86 -DCONF_FILE=prj_tls.conf ..
$ make run
In file included from
/home/<user>/zephyr/include/net/http.h:11:0,
from /home/<user>/zephyr/samples/net/http_client/src/main.c:19:
/home/<user>/zephyr/include/net/http_app.h:643:11: error: unknown type
name ‘net_app_cert_cb_t’
net_app_cert_cb_t cert_cb,
^~~~~~~~~~~~~~~~~
CMakeFiles/app.dir/build.make:302: recipe for target
'CMakeFiles/app.dir/src/main.c.obj' failed
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Of these, only struct net_ipv6_nbr_data::send_ns is a descriptive
change:
send_ns is used for timing Neighbor Solicitations in general, not
just for DAD.
The rest are typo/grammar fixes.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
- Add needed settings for DTLS support to the lwm2m_ctx structure.
- Add initialization of MBEDTLS to the LwM2M lib based on the
user application settings in lwm2m_ctx.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
This will avoid exposing IEEE 802.15.4 Zephyr's L2 private context data
to unrelevant places.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
L2 specific data and IEEE 802154 net mgmt interface are not related.
Plus, application may use the net mgmt part, not the L2 one. So let's
split the content in relevant headers.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
IPv6 mcast addr to MAC mcast conversion was factored out to
subsys/net/ip/l2/ethernet.c for reuse by other drivers.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Compute the length of the TX payload that is transported in one
IPv4 or IPv6 datagram taking into account UDP, ICMP or TCP
headers in addition to any IPv6 extension headers added by RPL.
The TCP implementation in Zephyr is known to currently carry at
maximum 8 bytes of options. If the protocol is not known to the
stack, assume that the application handles any protocol headers
as well as the data. Also, if the net_pkt does not have a
context associated, length check on the data is omitted when
appending.
Although payload length is calculated also for TCP, the TCP MSS
value is used as before.
Define IPv4 minimum MTU as 576 octets, See RFC 791, Sections 3.1.
and 3.2.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
- Renaming NET_L2_RAW_CHANNEL to NET_RAW_MODE
- Create a generic IEEE 802.15.4 raw mode for drivers
- Modify the IEEE 802.15.4 drivers so it passes the packet unmodified,
up to code using that mode to apply the necessary changes on the
received net_pkt according to their needs
- Modify wpanusb/wpan_serial relevantly
Fixes#5004
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add in6addr_any and in6addr_loopback which are defined in RFC2553 Basic
Socket Interface Extensions for IPv6.
Signed-off-by: Aska Wu <aska.wu@linaro.org>
In http_request() a CRLF is added to the header information after
the protocol is added. 2 CRLF in a row means the header information
is done, so following header information will be ignored.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Add status error string when sending a error message from
HTTP server to client as described in RFC 2616 ch 6.1.
Previously only error code was sent except for 400 (Bad Request).
This also fixes uninitialized memory access in error message.
Coverity-CID: 178792
Fixes#4782
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
