Renesas Renesas SmartBond(tm) have two ADC blocks:
GPADC and SDADC.
This change adds drivers for both.
Each ADC supports only one channel setup, drivers allow
to have multiply channels in sequence. Switching
between ADC sources in done in software.
GPADC has 10 bit resolution (accuracy can be increase
with oversampling). Values up to 3.6V can be measured
on selected pins. V30 and VBAT1 can also be measured.
SDADC has 14 bit resolution and can take measurements
from 8 pins (single of differential) and VBAT.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
This is a follow-up to commit 223cc3c6bd.
When a peripheral pin is disconnected, the pinctrl driver should skip
applying of GPIO configuration, as there is no pin number available in
such case, but due to an incorrect check, it actually did not skip it
and used an incorrect pin number for that. In nrfx prior to 3.0.0, this
caused an assertion failure, but because of a fallback routine, things
could still work in most cases (when assertions were disabled) as that
GPIO configuration was just applied to P0.31. Hence the bug was not
discovered until now. In the recent nrfx, this causes a null pointer
dereference, so always a crash.
This commit corrects the mentioned check and also uses the term "psel"
instead of "pin" where it is possible that the value is not a correct
pin number, in the hope of preventing a similar problem in the future.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Until now iterable sections APIs have been part of the toolchain
(common) headers. They are not strictly related to a toolchain, they
just rely on linker providing support for sections. Most files relied on
indirect includes to access the API, now, it is included as needed.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The i2c_npcx_controller does not actually implement the i2c API, that's
implemented in the port driver and the controller one is in support of
that. This means there's no need to use the I2C specific instance
define, as that would end up adding the stats structure that would never
get used.
This was originally added in 7b1349cfe6.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Status readback has been added in the latest silicon revision.
.port_get_raw and .port_toggle_bits are now supported
Signed-off-by: Andy Sinclair <andy.sinclair@nordicsemi.no>
Replace memcpy usage in write since it is not linked to non-external
flash which might cause read-while-write issues.
Move the function that invalidated the data cache inside the critical
section to avoid context switch before it is invalidated.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Check memc_flexspi_is_running_xip before calling
memc_flexspi_set_device_config in hyperflash init.
This aligns with the nor flash driver.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Hyperflash write operations resulted in invalid writes. This commit
fixes the issue by temporarily lowering the clock during writes.
This aligns with the mcux-sdk-examples.
Fixes https://github.com/zephyrproject-rtos/zephyr/issues/53855
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Add a function to update the flexspi bus clock. This is
needed when write operations are done to the hyperflash.
Signed-off-by: Jeppe Odgaard <jeppe.odgaard@prevas.dk>
Driver was based on can_sam. SAMC21 has only 1 interrupt for one
can "output", so can interrupt has to executes two lines of
interrupts.
CAN is configured to use OSC48M clock via GLCK7. GLCK7 is set
by divider configured from dts.
Signed-off-by: Kamil Serwus <kserwus@gmail.com>
Looks like a copy/paste error when copying runtime to empty to runtime
to full. Fixing so that we're assigning to the right union member.
Signed-off-by: Peter Rowley <perowle@microsoft.com>
The buffer registers (chemistry, manufacturer name, device name) were
not implemented. Implemented by adding a new api interface for
retrieving buffer properties. fuel_gauge_get_block_property has been
added, and uses a memory buffer allocated in the app in order to
store the fuel gauge information.
Signed-off-by: Peter Rowley <perowle@microsoft.com>
Current driver only allows state-of-charge. Adding relative-state-
of-charge and absolute-state-of-charge to differentiate between the
different types. Updated sbs and max drivers to support new enum.
Discussed in issue #57523
Signed-off-by: Peter Rowley <perowle@microsoft.com>
For systems with a true dynamic 1-Wire nature, the 1-Wire devices
cannot be defined in the DeviceTree (the number of slaves in
the system is not known during the build time).
In other words, there are no pre-defined 1-Wire devices on the bus in
DeviceTree, and thus the slave_count variable is always zero.
That means the skip_rom functionality will always be called even if
there are multiple devices connected to the bus.
This commit allows the user to override this original behavior and avoid
the skip_rom call by ignoring the slave count variable.
Also, this work preserves full backward compatibility.
Signed-off-by: Pavel Hübner <pavel.hubner@hardwario.com>
Add a driver for the Xilinx AXI Timebase WDT logic core. This can be
instantiated on various Xilinx FPGA-based platforms such as the
Digilent Arty, although it is not part of the default image used with
the Zephyr board configuration.
The driver can also optionally implement the HWINFO API to allow
determining whether the last system reset was initiated by the WDT.
Since this is a standalone IP core which could be used a variety of
configurations, this support is optional in case the system/SoC it is
used with already implements this support.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
This driver implement basic functions of ili9342c controller
which comes mostly with IPS displays.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
The i2c shell write command outputs the error "Failed to read from
device" while it tries to write data to device.
This fixes the error by outputting "Failed to write to device" instead.
Fixes:
uart:~$ i2c write i2c@3ff53000 23 01
Failed to read from device: 23
Signed-off-by: Gaël PORTAY <gael.portay@rtone.fr>
This patch enables the PLL clock output and PLL ref clock
for second ethernet module in NXP's i.MxRT106x SoCs
Signed-off-by: Sumit Batra <sumit.batra@nxp.com>
1. spi.h is included twice. Remove one of the two "#include"
declarations.
2. The 'if' clause requires braces even for one line body.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The LSM6DSV16X is a system-in-package featuring a 3-axis digital
accelerometer and a 3-axis digital gyroscope for industrial and IoT
solutions. The LSM6DSV16X embeds advanced dedicated features such as
a finite state machine (FSM) for configurable motion tracking and a
machine learning core (MLC) for context awareness.
https://www.st.com/en/mems-and-sensors/lsm6dsv16x.html
This driver is based on stmemsc HAL i/f v2.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Current implementation of `nrfx_pwm_stopped_check()` doesn't work
as expected when user doesn't provide event handler.
Workaround for that is to use low level function for checking whether
STOPPED event arrived.
The workaround should be removed when `nrfx_pwm_stopped_check()`
will contain needed functionality.
Signed-off-by: Adam Wojasinski <adam.wojasinski@nordicsemi.no>
Set a thread name for the npcx keyboard scan task so it can easily be
identified in the stack dump shell command.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Various coding style fixes, typos, and others on the NPCX keyboard scan
driver. No functional changes.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Convert the NPCX keyboard scan driver to the input subsystem and add the
input to kscan compatibility driver to maintain functionality with the
current API.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
video_mcux_csi_init, which setups the CSI pins (i.e: calls
pinctrl_apply_state) was called after mt9m114_init which tries to do i2c
communication with the camera to read the chip id. But since one of the
CSI pins is the camera master clock, doing things in this order won't
work. This PR inverts the order in which the devices are initialized.
Signed-off-by: Michele Balistreri <michele@bitgamma.com>
The function to enable wakeup from deep sleep modes is not
available on all SoC's. Hence compile this only when the
wakeup_source property is enabled.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Change init level of the mcux lpc dma driver to be
PRE_KERNEL_1 because some other hardware drivers
used on the same platforms as the lpc dma will be
dependent on the LPC DMA and are also initialized
in PRE_KERNEL_1, such as the Flexcomm UART driver
when using UART_ASYNC_API.
Therefore, remove k_malloc from init function and
make those variables statically defined instead of
heap allocated.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Some miscellaneous fixes to LPC DMA driver regarding status tracking:
- If a DMA channel has not been configured for any transfer,
there will be a bug caused by the virtual channel being -1
and then trying to index -1 into the driver data structs.
Add -EACCES return code to indicate this situation.
- Return -EINVAL from get_status if channel number is invalid
- Update the busy flag in the LPC DMA callback function.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Fixes for bug:
https://github.com/zephyrproject-rtos/zephyr/issues/57560
* don't do CCC if no i3c devices in device tree
* don't wait for MCTRLDONE status when issuing stop
* don't do data part of transfer if buf_sz is 0
* don't limit transfers to only i2c devices in the device tree
so "i2c scan" shell cmd works as expected
Signed-off-by: Mike J. Chen <mjchen@google.com>
Commit 246393e830
("drivers: spi: spi_nrfx_spim: Remove nrf_frequency_t handling")'
introduced two changes, one of them is removing the function
get_nrf_spim_frequency with a strange justification.
This change breaks support for peripherals written in a common way,
where the maximum frequency is set to the maximum supported
by the peripheral, not the controller, see shields for example.
On the occasion of bringing it back, the original function was
refactored to be easier to read and understand.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add a USB device controller driver skeleton to use as a starting point
for implementing a specific driver.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
API function:
- `pl011_irq_tx_enable` is expected to enable and trigger TX interrupt.
Due to HW limiation, PL011 won't trigger TX interrupt if some data
wasn't filled to TX FIFO at the beginning. So that `isr_cb` must be
called at first time to enable TX irq.
- `pl011_irq_tx_ready` will return true when FIFO can accept more
data. Here we don't need wait TX FIFO to be empty.
- `pl011_irq_tx_complete` will return true when all data have been
sent from the shift register.
Signed-off-by: Huifeng Zhang <Huifeng.Zhang@arm.com>
To reduce the interrupt latency of MIWU events, the driver prepares a
dedicated callback function item list for each MIWU group in this PR. We
needn't check the MIWU table and group of the event in ISR. And the
maximum item number of each list is also limited to 8. After applying
this PR, the interrupt latency reduces to ~10us consistently.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Glitches were observed if a GPIO pin was configured by
ROM to a non-default state and then Zephyr PINCTRL
reconfigured the pin. The fix involves using the correct
PINCTRL YAML output enable and state flags. Reading the
current spin state and reflecting into new pin configuration
if the pin is output and the drive low/high properties are
not present. We also take advantage of GPIO hardware reflecing
the alternate output value in the parallel output bit before
enabling parallel output mode. Interpret boolean flags with
both enable and disable as do not touch if neither flag is
present. We give precedence to enable over disable if both
flags mistakenly appear. Note, PINCTRL always clears the
GPIO control input pad disable bit.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
A glitch was observed if a GPIO PIN was configured to a
non-default state by ROM and then Zephyr programs the pin
for the same configuration. Root cause is GPIO hardware
implementing two output bits for each pin. The alternate
output bit is in the pin control register and is r/w by
default. The other bit exists in the GPIO parallel ouput
register and is read-only by default. The hardware actually
reflects the pin's output value into both bits. The fix is
to configure the pin with alternate output bit read-write
and the last step is to disable alternate output which
enabled read-write of the parallel bit. GPIO API's can
then use the GPIO parallel out registers. Add logic to
return an error from the GPIO interrupt configure API if
a pin is not configured as an input. Hardware only performs
interrupt detection if the input pad is enabled.
Hardware supports a pin being configured for both input
and output. Applications should add the GPIO_INPUT flag
to all pin configuration requiring interrupt detection.
The interpretation of input and output flags for the
get configuration API appears to be only one of the
flags can be set. Please refer to the GPIO driver tests.
Updated GPIO interrupt configure to clear the input pad
disable bit due to interrupt detection HW is connected
only to input side of pin.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
Bug 1: Fix lsm6dsl_gyro_set_fs_raw does not clear FS125 to register when
setting the full range to be other values.
Bug 2: Fix lsm6dsl_gyro_channel_get does not use the current
gyro_sensitivity when getting data from the gyroscope.
Signed-off-by: Jackie Yang <jackie@jackieyang.me>
Several sections of the STM32 ADC driver are #ifdef by a combination of the
same SOC defines that share similar IPs. These are F2/F4/F7/L1, and
F1/F37x.
Each of these combinations is now replaced by a specific compatible, which
makes the code a bit lighter and more succinct.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add ifdef around some functions that don't exist for STM32F37x (ADC_V2_5)
like it is done for STM32F1x.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Inverts the logic of some #ifdef, replacing lists of newer series by a
list of NOT older series. This makes it shorter, and more future-proof as
future series are more likely to work out of the box, without need to
manually add a new define in each place.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Some STM32 families that need to check the ADRDY flag after enabling the
ADC were not doing it. The #ifdef has been updated to fix that.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
