Working through either Motion detection or through Data-Ready.
Data-ready has a back-up timer to trigger worst case, if no motion
occurs within 10X data-rate.
On every streaming event, the driver checks for the sensor health, and
attempts recoverying its state if it detects issues.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
- Add bus support for SPI (based on RTIO).
- Support read/decode API for one-shot reads on the following channels:
- SENSOR_CHAN_POS_DX.
- SENSOR_CHAN_POS_DY.
- SENSOR_CHAN_POS_DXYZ.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
- Rejected non 2.4GHz band channels from Wifi-Scan.
- Overrode the WIFI_MGMT_SCAN_CHAN_MAX_MANUAL parameter to 50.
- Added check for wrong interface and invalid states
Signed-off-by: Nitin Pandey <nitin.pandey@silabs.com>
- For MCUX LPUART driver, added support to control RTS line
High/Low from other driver/app code.
- This control is required to wakeup other device which is
in sleep and configured its wakeup-source as UART-CTS line.
Signed-off-by: Nirav Agrawal <nirav.agrawal@nxp.com>
unify error codes from all drivers based on stepper specification
add a generic test case for set_micro_step_interval and stop
Signed-off-by: Jilay Pandya <jilay.pandya@outlook.com>
Soft reset HS400x during initialization to make sure that
device is at a known state and writeable registers have the
default values.
Signed-off-by: Ioannis Damigos <ioannis.damigos.uj@renesas.com>
Do not start the LF clock unless CONFIG_CLOCK_CONTROL_NRF is enabled.
This is similar to how it's done in Nordic's GRTC driver.
Authored-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
- added flag in nxp setup driver to perform HCI controller firmware-
load and configuration only once. This avoid loading/setting-up
controller fw on successive bt_init() after bt_disable() call.
Signed-off-by: Nirav Agrawal <nirav.agrawal@nxp.com>
- added HCI command to send hci-reset in bt_disable() func, and
remove its call from the driver close() call.
- remove rsp buf pass to 'hci_reset_complete()' func as status is
already checked under 'bt_hci_cmd_send_sync()'.
Signed-off-by: Nirav Agrawal <nirav.agrawal@nxp.com>
Initial AD405X driver supporting sampling, averaging
and burst averaging operation modes. Configurable
without interrupts or with device ready and
data ready interrupt.
Signed-off-by: Dimitrije Lilic <dimitrije.lilic@orioninc.com>
Add a choice `BT_NXP_MODULE` to make sure only one controller can be
selected if the multiple controllers are supported.
All NXP Bluetooth module similar with BT_NXP_NW612 should be added
to the section.
And set the BT_NXP_NW612 as the default controller.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Added queue for memory slab addresses to ensure that they
are released in correct order. Improved formula for frequency
scaling for nRF54H20. Fixed alternative channel mapping.
Signed-off-by: Michał Stasiak <michal.stasiak@nordicsemi.no>
According to the datasheet, maximum conversion time for both
humidity and temperature at 14 bits resolution is 1.7 ms.
Signed-off-by: Ioannis Damigos <ioannis.damigos.uj@renesas.com>
Setting frame size and endianess is now supported in UARTE HAL,
so these settings must have default values configured
to avoid compiler warnings about uninitialized fields.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
Some of the CLOCK events are associated with features
not available on every nRF device.
Signed-off-by: Nikodem Kastelik <nikodem.kastelik@nordicsemi.no>
It is observed that the regulatory domain API returns a failure
even when it has successfully completed its task. This change
addresses a minor fix to return the proper value to the user
when attempting to set the regulatory domain.
Signed-off-by: Vivekananda Uppunda <vivekananda.uppunda@nordicsemi.no>
We only need to dereference translate_config once to get the current
region_config we are working with, do this once at the start of the
sections that use it multiple times.
The compiler should optimize the multiple fetches anyway, so this
is purely for code readability.
Signed-off-by: Andrew Davis <afd@ti.com>
Instead of tracking if a matching address has been found and then
doing the translation after, we can loop until one is found and
do the translation and return immediately.
This saves having to keep a "found" variable, and makes the code
shorter and more readable IMHO. Do this here.
Signed-off-by: Andrew Davis <afd@ti.com>
Do not check virt being NULL as 0 is a valid address that can be
translated. Phys on the other hand is an output pointer that will be
assigned to and so cannot be NULL, check this instead to prevent a
NULL pointer dereference later.
Note that phys is allowed to be NULL, so this is not an invalid argument.
It can set to NULL when the caller wants to check if a virtual address is
mapped but does not care about the address itself. In that case -EFAULT
should be returned if the virtual address is not mapped, 0 otherwise.
For RAT, all addresses not translated are still valid and mapped as
pass-through, so we always return 0 in this check case.
Signed-off-by: Andrew Davis <afd@ti.com>
These struct and definitions are only used internally by this driver,
move them out of the public interface header and into the driver source.
Signed-off-by: Andrew Davis <afd@ti.com>
The struct address_trans_region_config is already defined, no reason
to pass this in as a void pointer then cast it later. Pass it in
as a struct pointer.
Signed-off-by: Andrew Davis <afd@ti.com>
This helper function is only used once and is way too small to need
to be factored into its own function. Inlining it greatly reduces
code size and complexity.
While merging, move the ASSERT()S out of the loop, they only need
checked once.
Signed-off-by: Andrew Davis <afd@ti.com>
video_format_cap needs to be terminated with a NULL entry
to allow looping over the formats.
Signed-off-by: Ibrahim Abdalkader <i.abdalkader@gmail.com>
native_posix has been removed, so let's remove its support from
kconfig for this driver.
Also let's replace its mention in the help message.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Correct the introduction comment, removing the native_posix mention,
and something which did not apply for several years.
Also remove an unnecessary include.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Including renaming the kconfig option
NATIVE_POSIX_TIMER into NATIVE_SIM_TIMER deprecating the first one.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Current system INTID calcualtion only worked for SoCs whose extended
interrupts started from IRQ 0.
Otherwise, FSL_FEATURE_IRQSTEER_IRQ_START_INDEX should be added for
system INTID.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
