Small update to have the central_multilink sample work correctly
with extended advertising (when enabled)
Signed-off-by: Troels Nilsson <trnn@demant.com>
Provide common helper functions to create extended extended Zephyr
Fatal Error functionality in HCI common code.
Use the implementation in hci_rpmsg sample.
The sample didn't provide an information about Controllers assert
or system fatal error to an application code while run with nRF5340
SoC. The goal for hci_rpmsg sample change is to enhance user experience
for conformance testing of the Bluetooth Controller while executed with
nRF5340.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
The unicast audio server sample did not set a location value,
and would report an invalid value of 0 when read.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This adds sample application that can be used as reference
implementation and for HAP qualification purposes.
Signed-off-by: Mariusz Skamra <mariusz.skamra@codecoup.pl>
In order to keep a flashed sample from provisioning forever, the sample
requires the user to press a button to provision a detected device.
The feature is only enabled if the board has a push button connected
via GPIO.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
The driver has be DT_INST based for a while so the Kconfig
symbols CONFIG_UART_RV32M1_LPUART_<n> aren't used. So lets
remove them.
Signed-off-by: Kumar Gala <galak@kernel.org>
The unicast client will now read the PACS location value
during the discovery procedure, as well as subscribing to
it.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
In the broadcast sink `scan_recv` which is called when we
scan for broadcast source, we now also provide the entire
AD struct to the application.
The reason for this is that the advertising data may
contain other information that is useful for the application
like the broadcaster device name or any other
vendor/application specific data.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Update the sample to reset data and restart scanning for new
unicast audio servers if the connected one disconnected.
This does not handle if a disconnect happens in the middle of
setting up the audio streams.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Modify how the ISO channels are allocated for the audio streams,
as well as how the CIG is allocated for the unicast group.
This fixes an issue where the unicast group could not be
fully allocated before _after_ the bt_audio_streams had been
configured by bt_audio_stream_config, thus making it impossible
to create a unicast group before the connections have been established.
This leaves us with 3 basic data types:
1) Streams allocated by the application
2) Endpoints that represent ASEs
3) Audio_iso which is used to couple streams and ISO channels.
The Unicast Group for the unicast client will now have the same
lifetime as the ISO CIG for the central.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Instead of rejecting metadata at the BAP layer, we now
expect the higher layer to provide the verification.
The reason for this is that the higher layer may be better
equiped at determining which metadata it supports.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This fix removes the Streaming_Audio_Context LTV from the LC3 Codec
helper macro, and subsequently a faulty exposure of this LTV in the
PAC records used.
Signed-off-by: Fredrik Danebjer <fredrik@danebjer.com>
Fixed handling of k_sem_take() return codes.
Also some minor cleanup in broadcast_audio samples.
Signed-off-by: Erik Robstad <erik.robstad@nordicsemi.no>
The codec (or rather codec configuration) is now taken from the
previously received BASE. This also means that the BASE (with
the codec configurations) is now also stored statically.
When the application attempts to synk to the broadcaster
the stack will lookup the codec configuration based on the
bis index, as a BASE may have multiple subgroups
with multiple codec configurations.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add support for using PACS and/or capabilities for
the broadcast sink role. PACS and capabilities were
originally only supported for the unicast server
role, so the PACS callbacks were moved their own
struct, as if a device supports both the unicast
server role and the broadcast sink role, it will
only have a single PACS instance.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
As Zephyr currently requires CMake version 3.20.0, update all
occurrences of cmake_minimum_required.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
- update device tree pin states definitions and node
descriptions to group pins sharing common properties.
- update ESP32's in-tree overlays.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
The BT_CODEC_LC3_CONFIG_* macros had a hardcoded location
and context, which makes them a lot less usable.
Updates the macro, and the macros that used them.
This also removes the BT_CODEC_LC3_CONFIG and instead
just uses the BT_CODEC_LC3_CONFIG_N macro, which has
then been renamed to BT_CODEC_LC3_CONFIG.
As an addition, the macros and their input has
also been better documented.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Logging v1 has been removed and log_strdup wrapper function is no
longer needed. Removing the function and its use in the tree.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Modified the samples such that the client will attempt to
setup 2 sink streams and 1 source stream, basically
representing a headset use case.
This also excercises both setting up a unidirectional
and a bidirectional ISO channel using the 3 audio streams.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The sample used `net_buf_ref` to send the same data multiple
times on multiple streams, but the send procedure, which
ends up calling bt_conn_send_cb, does not work
with multiple refs. We thus replace the refs with net_buf_clones.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The timeout was accidentally changed from 60 seconds
to 0.6 seconds.
This commit also fixes the number of prints, since we are now
sending at 10ms intervals.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Samples peripheral_gatt_write and central_gatt_write to
demonstration use of GATT Write Command.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
The controller does not support connected ISO yet, so it does not make
sense to build it form devices that build both host and controller.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
Remove v1 implementation from log_core and all references in the tree.
Remove modules used by v1: log_list and log_msg.
Remove Kconfig v1 specific options.
Remove Kconfig flags used for distinction between v1 and v2.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This test only runs on one platform, so make sure we do not exclude the
only platform using some other hardware related filters.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Rename the BT_ISO_INTERVAL_MIN/MAX to
BT_ISO_SDU_INTERVAL_MIN/MAX to avoid confusing this
the the ISO interval which is different from the SDU
interval.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add two new parameters to bt_iso_chan_send:
sn: The packet sequence number which shall be incremeted
per SDU interval.
ts: An optional timestamp value used to synchronize SDUs.
The sequence number in the API uses a 32-bit value even though
the sequence number for the HCI command is 16-bit. This is to
properly handle wrapping of sequence numbers, which is much
easier to do with additional bits allocated.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Provided sample support for Telink tlsr9518adk80d board.
Set CONFIG_BT_TINYCRYPT_ECC=n (supported by BLE controller).
Signed-off-by: Yuriy Vynnychek <yura.vynnychek@telink-semi.com>
The ISO security implementation works by verifying
against the acl (bt_conn) sec_level field. The
bt_conn sec_level field is only available
if CONFIG_BT_SMP is enabled, so this commit
adds guards for all ISO security checks as well.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The check did not properly check the info->flags as a bitfield,
and thus never decoded the data.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Increases the scan and adv data sizes to better support
the extended advertising data and periodic advertising
data (BASE).
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Clean up some of the board specific configuration files.
Removed all CONFIG_BT_CTLR* configs from the nRF5340
appcore conf files as that does not compile the controller.
Ensured that the ISO buffer in the controller for
nRF52840 can contain SDUs from all BAP LC3 minimum
requirements, as the controller does not yet
support segmentation of SDUs.
Also fixed a few bad configurations (broadcast sink not
enabling the sync support etc.).
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Remove the explicit enable of Extended and Periodic
Advertising support in Controller, the feature is no
longer experimental in the Controller and is now enabled
by default when application uses them by enabling as
Host feature.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add a call to bt_iso_chan_get_info for each CIS in the sample
to ensure that we don't attempt to send any data on a CIS
that is RX only.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add two new Kconfigs: BT_ISO_CENTRAL and BT_ISO_PERIPHERAL
that is used to do central or peripheral only builds,
similar to the BT_CENTRAL or BT_PERIPHERAL Kconfigs.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The audio stream receive callback now contains a
recv_info struct, which contain crucial information
such as timestamps and packet validity.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
