The "nm_bsp_reset" is used to apply a hard reset to the WINC board by
setting CHIP_EN and RESET_N signals low,then after specific delay
the function will put CHIP_EN high then RESET_N high.
reset-gpio is however defined as active low , causing this function
to hold the wifi module in reset.
Signed-off-by: Andreas Ålgård <aal@ixys.no>
When CAN is used, HSFLL frequency must >= AUXPLL frequency. Make sure to
send a request to the HSFLL clock instance.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Instead of assuming that an individual axis must contain all
data-values. Additionally, for determining that there's XYZ data, all
three channels must be present in the header.
Signed-off-by: Luis Ubieda <luisf@croxel.com>
For the supported channels, instead of just allowing 3-axis data being
printed out, allow individual channels to be processed (e.g: accel_x,
gyro_y, etc).
Signed-off-by: Luis Ubieda <luisf@croxel.com>
Wait until the typical time that the sample would be ready before
starting to poll the status register.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Rename _XFR_.*BITS and _WRITE_ONLY_ABSENT according to MISRA-C standard
rules 21.1 and 21.2 (Zephyr rules 121 and 122). For details see Zephyr
coding guidelines in table "Main rules".
Signed-off-by: Stephan Linz <linz@li-pro.net>
Use a string for the xfr-min-bits property over an integer value, as this
significantly improves the readability of the MIPI DBI SPI device binding.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Updated various device definition macros to use the DT_INST variants for
consistency and improved readability.
Signed-off-by: Dong Wang <dong.d.wang@intel.com>
Request fast global domain to run at 320 MHz during fast UARTE
activity. As request is asynchronous it cannot be called from
an ISR. Due to complexity to handle that without device runtime
power management a requirement is added so that if fast UARTE
is used device runtime PM must be enabled. Clock is request
and released in PM resume and suspended actions which in case
of fast UARTE are only called from thread context.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
Add requesting for global HFSLL when fast instance TIMER (e.g.
TIMER120 in nrf54h20) is used.
Signed-off-by: Krzysztof Chruściński <krzysztof.chruscinski@nordicsemi.no>
- Bring macro defined of RA8 in flash_hp_ra.h to device tree
- Change to use irq_lock instead of semaphore for code flash
- Modify and add conditions to check and make decision to perform
action at last block.
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
Signed-off-by: Tran Van Quy <quy.tran.pz@renesas.com>
This implements to generate the MAC address of the device UUID.
The UUID is hashed to reduce the size to 3 bytes.
Ideas taken from eth_nxp_enet.c
Adding dependencies on: HWInfo and CRC
Signed-off-by: Adib Taraben <theadib@gmail.com>
Fixes issue introduced in #76460
The previous code attempted to detect whether TMAG5273 or TMAG3001 was
connected based on DEVICE ID register. This doesn't work as the bits that
denote the version on one part are undefined on the other part, and cannot
be relied on to be zero.
This commit adds a TMAG3001 compatible which (for now) is just derived from
the TMAG5273 compatible. This allows TMAG3001 to be specified directly in
the DT. The driver code is updated to support both compatibles.
Signed-off-by: Yiding Jia <yiding.jia@gmail.com>
The three sensor channels listed below were recently added by the commit
9471df95a5:
- SENSOR_CHAN_GAME_ROTATION_VECTOR
- SENSOR_CHAN_GRAVITY_VECTOR
- SENSOR_CHAN_GBIAS_XYZ
Theses channel names are missing and causes a system crash if the
SENSOR_LOG_LEVEL is set to DEBUG.
Also, the two sensor attributes SENSOR_ATTR_GAIN and SENSOR_ATTR_RESOLUTION
were added by the commit f849140de7.
This adds these missing channel and attribute to the list of names in the
sensor shell.
Signed-off-by: Gaël PORTAY <gael.portay@rtone.fr>
Update the driver to take the "vrefint-cal-resolution" property into
account when performing the calculations.
Signed-off-by: Mathieu Choplain <mathieu.choplain@st.com>
The previous re-organization has the zephyr-keep-sorted defines
missing. Add them for the I2C drivers and targets. Also
moved lines to fix out-of-order violations.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
After writing option bytes, force them to be loaded. Failing to perform
this step means the values are never applied and not actually written
to non-volatile memory.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Fixes issue #83555, where UART transmit operations fail in Zephyr
sysbuild projects using MCUboot and the asynchronous UART API
(`CONFIG_UART_ASYNC_API=y`) on SAM0 devices such as the
ATSAMC21G18A.
The issue occurs because the DMA controller is not reset during
initialization, causing `BASEADDR` and `WRBADDR` registers to retain
MCUboot's configuration. This prevents the application from reconfiguring
these registers to its own RAM addresses, leading to UART transmit
timeouts and triggering the `UART_TX_ABORTED` callback.
This patch resolves the issue by resetting the DMA controller during
initialization in `dma_sam0.c`. The following actions are performed:
- Disables the DMA and CRC modules.
- Applies a software reset to ensure a clean state for reconfiguration.
With this change, UART transmit operations work as expected, improving
stability and compatibility between MCUboot and the application.
Signed-off-by: Tristen Pierson <tpierson@electrohire.com>
This is a squash of all the groundwork needed to
get a functioning driver for the DS3231 with the RTC API.
Signed-off-by: Gergo Vari <work@gergovari.com>
first check if the chip has a hosh module to futher filter MAC addresses
if not then enabling the pass through for all multicast protocols
Signed-off-by: Adib Taraben <theadib@gmail.com>
Use the same Kconfig for all drivers to configure if the FCS bytes
(checksum) should be included in the packets passed to L2.
The description is slightly reworded to make clear that it does not
only affect the length, but the packet content itself.
Signed-off-by: Martin Jäger <martin@libre.solar>
The parameter provided to the `BIT()` macro must be checked so that
the shift operation does not overflow the variable.
Fixes#81990
Signed-off-by: Martin Jäger <martin@libre.solar>
The osal apis spinlock - take, release and bus qspi sleep
are trying to use ops after deinit. So removing osal deinit
for temporary workaround.
Signed-off-by: Kapil Bhatt <kapil.bhatt@nordicsemi.no>
Add variable network configuration control into the driver to optimize
RAM usage by default. The pool sizes are default, and tuning is left to
the applications or samples.
Signed-off-by: Triveni Danda <triveni.danda@nordicsemi.no>
Update the context state parameters when the context is already locked.
This allows changing the callback information for asynchronous
operations while the context is locked.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Do not unlock CR at the end of initialization.
The lock mechanism is to protect unwanted registers modifications due to
software bugs. There is no point in leaving the registers unlock once
the driver is initialized.
Signed-off-by: Dawid Niedzwiecki <dawidn@google.com>
Currently, the uart_wch driver only supports the polling API.
This patch introduces bindings for the interrupt-driven API.
Signed-off-by: Paul Wedeck <paulwedeck@gmail.com>
When attaching a device, it should look up if the dynamic addr is
already attached only, and not by the static addr.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
