Update sample espi driver test to exercise some SAF functionality
based on the limited hardware available. Note the SAF test will
erase a section of the flash. SAF tests are enabled for the EVB only.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Nordic watchdog does support a callback, but it has a time limit that
is too tight for the way this sample uses it. Add infrastructure to
bypass using the callback in this sample.
Also add more diagnostics explaining the status of callback use in the
sample.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Similarly to what was done for watchdog test,
update watchdog sample to be compatible with stm32 window watchdog
and enable testing by twister.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add some changes to adc sample to enable valid verdict generation
using twister:
-Replace 'single_line' keyword with correct 'one_line'
-Remove parenthesis from the sample output to enable regex verdict
-Add timeout to save time in execution
Additionally, add support for disco_l475_iot1.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Clean up logging menuconfig by grouping configuration into
sections like: mode, processing configuration, backends.
Additionlly, removed LOG_ENABLE_FANCY_OUTPUT_FORMATTING which is no
longer in use.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This sample shows how to use the ADC API. Depending on the support of
sequential reads in the driver, 1 or 2 channels are read and printed.
A devicetree overlay is necessary to specify the used ADC channel(s).
Signed-off-by: Martin Jäger <martin@libre.solar>
The flash shell can now build when there isn't a chosen
zephyr,flash-controller available, so we can simplify the filter to
apply this sample to more boards.
Two STM32 H7 board configurations are excluded because the flash driver
isn't supported yet on the M4 core.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Remove UP Squared support for the gpio sample that was merged after
the sample itself was removed.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
DW16 provides information on mechanisms to enter and exit 4-Byte
address modes, returning the device to reset state, and how to
manipulate the values in the first status register.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
DW15 provides information on entry and exit from QSPI modes. In
particular, it specifies whether and how the status register must be
updated for this feature.
Add a JESD216 devicetree property for the Quad Enable Requirements
value.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Modify led_pwm sample in order to make it usable in device testing:
- Remove parenthesis from the logs as they prevent use of regex
- Add a harness_config multiline regex in order to enable verdict
generation
- Update README
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Currently the following shields will thus be supported
waveshare_epaper_gdeh0154a07
waveshare_epaper_gdeh0213b1
waveshare_epaper_gdeh0213b72
waveshare_epaper_gdeh029a1
Signed-off-by: Kim Bøndergaard <kim@fam-boendergaard.dk>
Signed-off-by: Kim Bøndergaard <kibo@prevas.dk>
Convert the driver so that it creates its instance basing on DT.
Remove no longer needed Kconfig option CRYPTO_NRF_ECB_NAME.
Also update accordingly the crypto sample.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
CAN_MCP2515_MAX_FILTER is not needed anymore and was probably just a
misunderstanding. Aligned it with the other CAN drivers.
This also was the last difference in the mcp2515 specific config for the
can sample, so that can be deleted as well.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
Reordering of the struct elements to match the Linux format.
The __packed() is not necessary anymore.
std_id and ext_id is merged to id in the frame and filter.
Additionally, the frames are ready for CAN-FD.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
The previous API can't change the sampling-point and only allowed
bitrates that fit the time segments.
The new API allows for shifting the sampling-point and adjusts the
number of time quantum in a bit to all more possible bitrates.
The functions to calculate the timings are moved to the can_common file.
They can be used for all drivers.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
some tests configured with CONFIG_NEWLIB_LIBC=y,
it's better to add a filter filter: TOOLCHAIN_HAS_NEWLIB == 1
in those tests yaml file.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
- Remove SYS_ prefix
- shorten POWER_MANAGEMENT to just PM
- DEVICE_POWER_MANAGEMENT -> PM_DEVICE
and use PM_ as the prefix for all PM related Kconfigs
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This adds a sample application for testing
the LiteX clock control driver.
Signed-off-by: Pawel Czarnecki <pczarnecki@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Do not enable CONFIG_SERIAL explicitly in the flash_shell sample. Leave
it up to the board definition to enable a suitable shell backend if
CONFIG_SHELL is enabled.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Adjust the sanitycheck filter of the flash shell sample to also depend
on the board having a chosen zephyr,flash-controller devicetree node (as
this is what is referenced in flash_shell.c).
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
The sanity check on this sample gives timeout failure
on reel board because of bad filtering. Because the
sample does not adopt ztest framework, sanitycheck in
our daily test will report this as failure, which lowers
our passrate but this is not a sample with errors.
Signed-off-by: Shihao Shen <shihao.shen@intel.com>
The sample is currently to tied to nrf9160dk_nrf9160 board. Refact to
allow build with board and select between device power management on or
off. Move nrf9160dk_nrf9160.overlay to proper boards directory and add
nrf9160dk_nrf9160.conf to set the correct device. Device PM needs SYS
PM be implemented and is an specific configuration and for those boards
that have it implemented user can add overlay-pm.conf to enable the
feature.
Fixes#28094.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The WS2812 SPI driver needs the pixel data to be clocked out on time,
with no gaps between SPI frames. This makes the nordic,nrf-spi
compatible unsuitable for use, since the corresponding driver doesn't
use EasyDMA to clock out the tx buffers.
Force the arduino_spi node in the DT to SPIM mode by setting its
compatible to nordic,nrf-spim. On nRF52832, this driver is disabled by
default due to Product Anomaly Notice (PAN) 58.
We happen to not be affected by PAN 58 in this instance, because we
never read data over the SPIM, only write it. So it's safe to enable
the SPIM driver. This requires a board-specific Kconfig fragment for
nRF52-DK to enable CONFIG_SOC_NRF52832_ALLOW_SPIM_DESPITE_PAN_58.
Fixes: #29877
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Improve the way the nrf_qspi_nor driver configures the SCK frequency,
to properly support QSPI also on nRF53 Series SoCs that use a different
base clock frequency (96 MHz).
Add also a relevant configuration in the spi_flash sample so that it
can run on the nRF5340 DK.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This sample allows to test the led-pwm driver. The first "pwm-leds"
compatible device instance found in DT is used. For each LEDs attached
to this device (child nodes) the same test pattern (described below) is
executed. The LED API functions are used to control the LEDs.
Test pattern:
For each PWM LEDs (one after the other):
- turn on
- turn off
- increase the brightness gradually up to the maximum level
- blink (0.1 sec on, 0.1 sec off)
- blink (1 sec on, 1 sec off)
- turn off
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
In npcx7 series, all of them support the Intel Enhanced Serial
Peripheral Interface (eSPI) Revision 1.0. This specification provides a
path for migrating host sub-devices via LPC to a lower pin count, higher
bandwidth bus. In addition to Host communication via the peripheral
channel, it provides virtual wires support, out-of-band communication,
and device mastering option over the Chipset SPI flash.
Becisdes introducing eSPI device in npcx7, this CL also includes:
1. Add eSPI device tree declarations.
2. Add npcx7-espi-vws-map.dtsi to present the relationship between eSPI
Virtual-Wire signals, eSPI registers, and wake-up input sources.
3. Zephyr eSPI api implementation.
4, Add OOB (Out of Band tunneled SMBus) support.
5. Add configuration files for eSPI test suites.
Signed-off-by: Mulin Chao <MLChao@nuvoton.com>
Remove obsolete include of the shell_uart.h file.
It is sufficient to include the shell.h file.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordisemi.no>
ESPI is supported in MEC15 chips but similar to PECI, I2C, eSPI bus
testing requires another device to act as eSPI host.
While this sample can be run in EVB the HW connection to a eSPI host
(Intel RVP) is not documented/supported.
Mark as not supported in that HW only in Modular card
(which setup is documented)
Also remove duplicate definition of the "depends_on: espi"
in the end of the sample.yaml file
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Two samples require interacting with keyboard and mouse, and that
means necessary to provide correct fixture before run of that samples
in sanitycheck system. To skip or run the sample according to the
provided fixture in map-file necessary to add fixture definitions
into sample.yaml files
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Add the supported features section to serpente.yaml and overlay files
to the corresponding tests and samples.
Signed-off-by: Alexander Falb <fal3xx@gmail.com>
Add support for running the JEDEC SPI NOR flash sample on the ARM
Cortex-M3 DesignStart FPGA reference implementation.
Special care is needed to avoid overwriting part of the FPGA
configuration bitstream, which is stored in the onboard QSPI flash.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
