Added sample to show disk access and FS api with
Fat filesystem and SDHC driver. Tested working with
nrf52840 (blip).
Signed-off-by: Tavish Naruka <docuser@docs.electronut.in>
Add section for build sanity check configuration with
CONFIG_USB_COMPOSITE_DEVICE enabled.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add configuration for creating composite USB device with CDC ACM and
Mass Storage functions.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
New shell does not need either CONFIG_UART_CONSOLE
or interrupts support to be working. Only CONFIG_SERIAL
in combination with CONFIG_UART_SHELL_ON_DEV_NAME are required.
Updated sample yaml file accordingly.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
The removed test does the same thing and runs on the same platforms
as already existing samples/boards/nrf52/power_mgr.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The v2018.10 release of OpenAMP reworks the API set and splits the
remoteproc vs rpmsg interfaces so one can use rpmsg without remoteproc.
This helps drastically reduce the code footprint utilized by OpenAMP.
The remote see around 4k reduction in code size.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Removed foreground command functionality from shell source files.
Removed associated example.
Removed enter/exit command functions from the Bluetooth example
Updated project config files.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Legacy shell removed in order to avoid maintaining two shells
systems.
All examples and tests have been migrated to the new shell.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Disabled the CONFIG_COVERAGE for benchmarks and other tests.
This is needed because it interferes with normal behavior of the
test case.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This patch adds a x86_64 architecture and qemu_x86_64 board to Zephyr.
Only the basic architecture support needed to run 64 bit code is
added; no drivers are added, though a low-level console exists and is
wired to printk().
The support is built on top of a "X86 underkernel" layer, which can be
built in isolation as a unit test on a Linux host.
Limitations:
+ Right now the SDK lacks an x86_64 toolchain. The build will fall
back to a host toolchain if it finds no cross compiler defined,
which is tested to work on gcc 8.2.1 right now.
+ No x87/SSE/AVX usage is allowed. This is a stronger limitation than
other architectures where the instructions work from one thread even
if the context switch code doesn't support it. We are passing
-no-sse to prevent gcc from automatically generating SSE
instructions for non-floating-point purposes, which has the side
effect of changing the ABI. Future work to handle the FPU registers
will need to be combined with an "application" ABI distinct from the
kernel one (or just to require USERSPACE).
+ Paging is enabled (it has to be in long mode), but is a 1:1 mapping
of all memory. No MMU/USERSPACE support yet.
+ We are building with -mno-red-zone for stack size reasons, but this
is a valuable optimization. Enabling it requires automatic stack
switching, which requires a TSS, which means it has to happen after
MMU support.
+ The OS runs in 64 bit mode, but for compatibility reasons is
compiled to the 32 bit "X32" ABI. So while the full 64 bit
registers and instruction set are available, C pointers are 32 bits
long and Zephyr is constrained to run in the bottom 4G of memory.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Added macro that generates simple report descriptor for mouse.
This improves the readability of hid-mouse sample.
Signed-off-by: Marcin Szymczyk <Marcin.Szymczyk@nordicsemi.no>
Move to latest cmake version with many bug fixes and enhancements.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Exteneded shell sample with example how to use shell_fprintf from
any context with 'foreground' command.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Removed get_report_cb as it was an incorrect implementation
of Get_Report request. Correct response would be returning
current report value, not report descriptor.
Signed-off-by: Marcin Szymczyk <Marcin.Szymczyk@nordicsemi.no>
Added right button, X and Y axis movement to HID mouse example.
Enabled only if board has enough buttons.
Added LED toggling notification when report is sent.
Signed-off-by: Marcin Szymczyk <Marcin.Szymczyk@nordicsemi.no>
1. Created new shell module: shell_help.
2. Simplified command handlers with new shell print macros.
3. Removed help functions from command handlers.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Removed printing command help from help handler. It is now
realized by the shell engine. This change saves a lot of flash
but still allows to print help in command handler with function
shell_help_print.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Removing help "options" from shell API.
Currently SHELL_OPT macro is not used by users. What is more
commit: a89690d10f ignores possible options created in
command handler by the user. As a result they are not printed
in help message.
Second, currntly implemented "options" in command handlers options are
implemented without SHELL_OPT macro.
And last but not least this change will allow to implement
help handler in a way that user will not need to think about calling
functions printing help in a command handler.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
As it stands now, the console effectively works in raw mode, so all
messages should end with "\r\n". This was missed previously, because
the sample was run in QEMU, on top of POSIX cooked console. Running
on real hardware showed this issue.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Idle rate functionality has been implemented for HID USB class.
Bassed on Device Class Definition for Human Interface Devices 1.11.
Tested with USB3CV and host with idle rate.
Signed-off-by: Marcin Szymczyk <Marcin.Szymczyk@nordicsemi.no>
HID class now defaults to universal request callbacks in case they
are not provided by the application. This applies to following,
class-specific requests: Get_Report, Set_Report, Get_Idle, Set_Idle,
Get_Protocol and Set_Protocol.
Tested with USB3CV.
Signed-off-by: Marcin Szymczyk <Marcin.Szymczyk@nordicsemi.no>
Start of Frame events can now be accessed from USB classes.
This will be useful when implementing idle rate functionality.
Signed-off-by: Marcin Szymczyk <Marcin.Szymczyk@nordicsemi.no>
System Power Management is only supported in Tickless Idle mode.
This patch modifies Kconfig dependencies to ensure System Power
Management option selects Tickless Idle one.
Fixes: #11046
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Since setting USB console port name is moved to DTS users have
problems enabling it. Notify user that the console is not set.
Fixes#10693
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Adds the virtualcom device to the nrf52840 SoC dts and adds a board
specific nrf52840_overlay.dts file, copied exactly from the
arduino101_overlay.dts file, to set the console device name
appropriately for the subsys/usb/console sample project.
There were no clear alternatives to add a usb_cdc: virtualcom device to
all known SoC devices with USB support as should probably happen.
There was also no clear alternatives to add a non-board specific overlay
to the example.
This fixes a specific problem with the nrf52840-dk board for this sample
project.
Signed-off-by: Tom Burdick <thomas.burdick@gmail.com>
Add IMX IPM sample application. It reads the data sent to the
Messaging Unit and sends them back. It has been tested on Udoo Neo Full
board with the Cortex-A9 core running Linux and sending the data
into the Messaging Unit A and the Cortex-M4 running this sample Zephyr
application and reading the data from Messaging Unit B and sending it
back for Linux side to read it from Messaging Unit A.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
We have cases with UART drivers where TX interrupt handling is not
bootstrapped properly on enabling them. To make such cases more
obvious, start this sample with console_write(), the output of which
wouldn't appear if that's the case. (Of course, the sample starts
with printk() exlaining what may happpen.)
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This commit would add the pull-up or pull-down on the switch pin and
makes it functional on the board where there is no external pull-up.
Signed-off-by: Radoslaw Koppel <radoslaw.koppel@nordicsemi.no>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
If shell UART backend was enabled and logger uart backend was
not explicitly disabled then both were used resulting in logs
being printed twice on terminal.
Patch modifies default state of log uart backend to depend on
state of shell uart backend.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
