This configures the nucleo_wb55rg board for testing
the SPI loopback with DMA MUX transfer.
This test requires pin SPI_A_MISO (D12) to be connected
to pin SPI_A_MOSI (D11) on the nucleo_wb55rg board
Signed-off-by: Francois Ramu <francois.ramu@st.com>
After increasing SPI speeds on LPC family SoCs, the slow clock
speeds have been removed and default clock speeds are in use now.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Cloned from counter_basic_api with modifications based on DS3231
limitations:
* Only one device tested per board;
* Counter cannot be stopped or started;
* Alarms are serviced by worker thread, so are not invoked from ISR
and require that test thread yield to allow processing (no
k_busy_wait());
* Multiple Alarms test is disabled as documented in test.
Additional tests were added for DS3231-specific API.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This commit removes the redundant `LOG` and `LOG_IMMEDIATE` selections
in `prj.conf`, since the `TEST_LOGGING_DEFAULTS`, which is enabled by
default for all tests, selects `LOG` and `LOG_MINIMAL`.
This effectively allows the test to run with the default test logging
policy, set by the testing subsystem.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit removes the redundant `LOG` and `LOG_IMMEDIATE` selections
in `prj.conf`, since the `TEST_LOGGING_DEFAULTS`, which is enabled by
default for all tests, selects `LOG` and `LOG_MINIMAL`.
This effectively allows the test to run with the default test logging
policy, set by the testing subsystem.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the SPI testing support with an internal MOSI to MISO
loopback for the Atmel SAM R21 Xplained Pro board.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the SPI testing support with an internal MOSI to MISO
loopback for the Atmel SAM E54 Xplained Pro board.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
A number of uart drivers may not implement the uart_configure and
uart_config_get APIs, if we get -ENOTSUP treat that as a skip.
Fixes#24355
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The STM32 and CC13xx/CC26xx SPI drivers don't utilize the Kconfig
symbols for per instance SPI anymore so we don't need to set them on the
conf files for this test.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds the asynchronous UART API testing support on the SAM
E54 Xplained Pro board.
The SERCOM1 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM1 UART TX and RX pads are configured to be
internally connected; it is, however, still necessary to configure the
pinmux because the module pads are not connected until the pinmux is
configured.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The STM32 I2C drivers don't utilize the Kconfig symbols for per
instance I2C anymore so we don't need to set them in the
conf files for this test.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
harness being set without actual use of harness (via harness_config)
makes the test behave differently.
Fixes#24661
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert DT_RTC_0_NAME to DT_LABEL() references based on the compat being
defined in the build.
Introduce a set of macros that will generate a list of labels based on
compatible matches.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This configures the nucleo_f411re board for testing the SPI loopback
with DMA V1 transfer. DMA instance 2 is used.
This test requires pin SPI_A_MISO (D12) to be connected
to pin SPI_A_MOSI (D11) on the nucleo_wb55rg boardtest dma_V1
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This configures the nucleo_l476rg board for testing the SPI loopback
when with DMA transfer.
It requires pin MOSI to be connected to pin MISO of the SPI1
SPI tx/rx are assigned to the request ID 1 of dma1 channels 3 and 2
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds a new testcase in the spi_loopback test application
to use several buffers for the DMA transfer.
It requires the MOSI to be connected to the MISO of the SPI1.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This changes the spi_loopback test application to use the DMA transfer.
In case of DMA, some testcases are useless.
It requires the MOSI to be connected to the MISO of the SPI1.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Convert DT_UART_{0,1}_NAME to DT_NODELABEL() references as the cases are
board specific and this allows us to remove DT_UART_{0,1}_NAME defines
in dts_fixup.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for running the DAC loopback test case on the NXP
FRDM-K64F development board.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add support for running the DAC loopback test case on the NXP
TWR-KE18F development board.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Substitute integral constants where call sites passed named constants
that have timeout values as arguments to parameters that expect
millisecond durations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Convert CAN to use a chosen node property that is similar to how we
handle zephyr,entroy or zephyr,flash-controller as the means to select a
specific peripheral instance utilized by a subsystem.
Replace references of the form:
alias {
can-primary = &can1;
};
with:
chosen {
zephyr,can-primary = &can1;
};
Replace various macro/define references with either
DT_CHOSEN(zephyr_can_primary) or replace DT_ALIAS_CAN_PRIMARY_LABEL
with DT_CHOSEN_ZEPHYR_CAN_PRIMARY_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The hwinfo driver test currently filters for `CONFIG_HWINFO`, but this
symbol is set to `y` by the `prj.conf` and therefore will always be
selected.
This commit removes the unnecessary `CONFIG_HWINFO` filter.
Note that the hwinfo driver test `ifdef`s `CONFIG_HWINFO_HAS_DRIVER`,
and having an actual hwinfo driver implementation is not a requirement
(if no hwinfo driver is available, the test validates that -ENOTSUP is
returned by `hwinfo_get_device_id`).
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Convert driver to use the new device tree macro's instead of
dts_fixup.h based macros. This moves us closer to removing both
dts_fixup.h and per instance Kconfig symbols.
The pinmux_mchp_xec is also being updated since it's using DT
from GPIO.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Replace DT_FLASH_DEV_NAME with DT_CHOSEN_ZEPHYR_FLASH_CONTROLLER_LABEL.
We now set zephyr,flash-controller in the chosen node of the device
tree to the flash controller device.
NOTE: For a SoCs with on die flash, this points to the controller and
not the 'soc-nv-flash' node. Typically the controller is the
parent of the 'soc-nv-flash' node).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Tests were failing as they were looking for an alias which didn't exist
Also, because some code in kscan_handlers.c wasn't compilable
Signed-off-by: Mark Olsson <mark@markolsson.se>
This commit adds the asynchronous UART API testing support on the SAM
R21 Xplained Pro board.
The SERCOM3 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM3 UART TX and RX pads are configured to be
internally connected; it is, however, still necessary to configure the
pinmux because the module pads are not connected until the pinmux is
configured.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Test is checking if alarm handler is executed at request time or later.
However, validation did not take into account wrapping of the counter.
Fixed by taking into account case where counter wraps.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Fixes test which did not take into account that counter may
wrap (nrf51 has 16bit timers) and was setting alarm to wrong
value. Error was not seen on platforms with higher top value.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This commit adds the asynchronous UART API testing support on the SAM
D21 Xplained Pro board.
The SERCOM1 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM1 UART TX and RX pads are configured to be
internally connected.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
No in-tree boards support the NINT signal on an SX1509B IO extender,
so test using custom overlays/configurations for the Particle Xenon
board using an SX1509B breakout board.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Changes to Kconfig vs devicetree resulted in uart1 being enabled,
which steals the test pins away from the test.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Move to the new devicetree API and stop using DT_WDT_0_NAME fixup
macros. All existing in-tree SoCs with fixup names are still supported
here via compatible. The watchdog0 alias is also still supported.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The board rename was missed. That's the only remaining case of a
missed rename I could find in tree, but I may have missed something.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Replace CONFIG_ENTROPY_NAME with DT_CHOSEN_ZEPHYR_ENTROPY_LABEL. We now
set zephyr,entropy in the chosen node of the device tree to the entropy
device.
This allows us to remove CONFIG_ENTROPY_NAME from dts_fixup.h. Also
remove any other stale ENTROPY related defines in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Updated the openisa,rv32m1_vega-pinmux binding to require the label
property and updated the rv32m1.dtsi to add label properties for the
pinmux nodes.
Also update gpio_basic_api test to use DT_NODELABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as spi. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The board name for the Thingy:52, so far known as nrf52_pca20020, is
renamed to thingy52_nrf52832. Its documentation and all references to
its name in the tree are updated accordingly. Overlay and configuration
files specific to this board are also renamed, to match the new board
name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF52840 Dongle, so far known as
nrf52840_pca10059, is renamed to nrf52840dongle_nrf52840. Its
documentation and all references to its name in the tree are updated
accordingly. Overlay and configuration files specific to this board are
also renamed, to match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF52833 DK, so far known as nrf52833_pca10100,
is renamed to nrf52833dk_nrf52833. Its documentation and all
references to its name in the tree are updated accordingly.
Overlay and configuration files specific to this board are also
renamed, to match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board target for emulation of nRF52810 on nRF5DK, so far
known as nrf52810_pca10040, is renamed to nrf52dk_nrf52810.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The board name for the nRF52 DK, so far known as nrf52_pca10040, is
renamed to nrf52dk_nrf52832. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to
match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Also update counter_basic_api test to use DT_INST and remove the
udoo_neo_full_m4.conf as its not longer needed since the per instance
Kconfig sybmols don't exist anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Additionally remove udoo_neo_full_m4.conf from gpio_basic_api test since
the Kconfig symbols don't need to be set anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Kconfig options that enable I2C and SPI instances are no longer used
in nRF drivers. Remove all assignments done to these options in related
board definitions, samples, and tests.
For nrf52_pca20020, also no longer needed setting of default values
for GPIO_SX1509B* options is removed (now the gpio_sx1509b driver is
enabled by default when a corresponding devicetree node is enabled).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `UART_x_NRF_UART*` that select
the type of nrfx driver (for UART or UARTE peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding UART node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between UART and UARTE for a given instance.
Since all `UART_x_NRF_UART*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
PWM and other flags were missing for PCA10059.
Aligned also RAM and Flash while comparing the files.
Signed-off-by: Markus Becker <markus.becker@tridonic.com>
Kernel timeouts have always been a 32 bit integer despite the
existence of generation macros, and existing code has been
inconsistent about using them. Upcoming commits are going to make the
timeout arguments opaque, so fix things up to be rigorously correct.
Changes include:
+ Adding a K_TIMEOUT_EQ() macro for code that needs to compare timeout
values for equality (e.g. with K_FOREVER or K_NO_WAIT).
+ Adding a k_msleep() synonym for k_sleep() which can continue to take
integral arguments as k_sleep() moves away to timeout arguments.
+ Pervasively using the K_MSEC(), K_SECONDS(), et. al. macros to
generate timeout arguments.
+ Removing the usage of K_NO_WAIT as the final argument to
K_THREAD_DEFINE(). This is just a count of milliseconds and we need
to use a zero.
This patch include no logic changes and should not affect generated
code at all.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
We rename the nRF91 Dev Kit board target (nrf9160_pca10090)
to nrf9160dk_nrf9160. We update all associated references
in the supportive documentation and all nRF9160-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Do not attempt to build on all boards. Instead, do a build-only pass
of the generic test case on all boards with EEPROM support.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Remove the dts_fixup.h with a DTS app overlay file instead. We have
sensors that show up on both the I2C and SPI busses, and we disable
the sensors to match how the tests work currently.
The app.overlay utilizes the testing dts bindings to create test nodes
that should not conflict with any existing SoC nodes. Thus allowing the
test to run on any platform.
The dts overlay is structured such that i2c.dtsi and spi.dtsi are
generated with default values for required properties. We than update
device properties for those nodes that the defaults are sufficient for
one reason or another.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Using find_package to locate Zephyr.
Old behavior was to use $ENV{ZEPHYR_BASE} for inclusion of boiler plate
code.
Whenever an automatic run of CMake happend by the build system / IDE
then it was required that ZEPHYR_BASE was defined.
Using ZEPHYR_BASE only to locate the Zephyr package allows CMake to
cache the base variable and thus allowing subsequent invocation even
if ZEPHYR_BASE is not set in the environment.
It also removes the risk of strange build results if a user switchs
between different Zephyr based project folders and forgetting to reset
ZEPHYR_BASE before running ninja / make.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
The board target for emulation of nRF52811 on nRF52840 DK, so far
known as nrf52811_pca10056, is renamed to nrf52840dk_nrf52811.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
We rename the nRF51 Dev Kit board target (nrf51_pca10028)
to nrf51dk_nrf51422. We update all associated references
in the supportive documentation and all nRF51-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The IIS2MDC is a 3D digital magnetometer ultra-low power sensor
for industrial applications, which can be interfaced through
either I2C or SPI bus.
https://www.st.com/resource/en/datasheet/iis2mdc.pdf
This driver is based on stmemsc i/f v1.02.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Tests were added for the UART configure API in #22849. The existing test
implementation works, but suggested to reduce dependency between test
cases. This commit allows each test to run independently of each other
by removing the function call of uart_config_get() in the
uart_configure() test case, and uses the uart_config_get() test case to
confirm the value set and gotten/read.
Fixes#23459
Signed-off-by: Jennifer Williams <jennifer.m.williams@intel.com>
Reworked calibration to not use HW platform which is not available on
some platforms (nrf53) and does not bring any value compared to using
system timer. Switched to use k_timer. Additionally, improved
calibration algorithm to request also LF clock before starting
calibration. This simplifies the algorithm because it does not need
to support disabling low frequency clock which in calibration.
Tests has been updated and simplified. Former tests relied on HW timer
event.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The ISM330DHCX is a ultra-low power IMU with a 3D digital accelerometer
and 3D digital gyroscope tailored for Industry 4.0 applications, which
can be interfaced through either I2C or SPI bus.
https://www.st.com/resource/en/datasheet/ism330dhcx.pdf
This driver is based on stmemsc i/f v1.02.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The bootloader on mec15xxevb_assy6853 clears the memory on reboot,
which would fail the wdt_basic_api test. Instead of simply exclude
the platform, add a build only test for this board so the watchdog
is being built to avoid build breakage.
Fixes#20301
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The IIS2DLPC is a 3D digital accelerometer ultra-low power sensor
for industrial applications, which can be interfaced through either
I2C or SPI bus.
https://www.st.com/resource/en/datasheet/iis2dlpc.pdf
This driver is based on stmemsc i/f v1.02
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Since commit 22326f6d99 got in, this test
requires that so-called NOP frames (bytes of value 0) are sent when no
TX data is provided. For nRF SoCs, the over-read character (ORC) that
is sent in such case is by default configured to the value of 0xFF.
Alter configurations for nRF boards so that 0x00 is used instead.
On the occasion, remove redundant selections of driver type in those
configurations (CONFIG_SPI_x_NRF_SPI[M]=y), as such selections must
be aligned with the value of "compatible" property in corresponding
nodes in dts, so there's no much sense in having them separately here.
Correct also the SPI instance to be used for nrf51_pca10028.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In most cases gpio_pin_configure()'s return value is checked in this
application; Coverity noted a case where it is not checked. Add a
check to make it happy.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Convert ak8975 sensor driver to utilize device tree.
This also supports the ak8975 embedded in a invensense MPU9150. In such
a case the device tree node should look something like, where the ak8975
is a child of the mpu9150.
mpu9150@68 {
compatible = "invensense,mpu9150";
reg = <0x68>;
label = "mpu9150";
#address-cells = <1>;
#size-cells = <0>;
ak8975@c {
compatible = "asahi-kasei,ak8975";
reg = <0xc>;
label = "ak8975";
};
};
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The UART API now supports configure and configure_get functions,
however no tests were written for those functions. This
commit adds the framework and implementing tests for configure
and configure_get for UART API.
Fixes (#12872)
Signed-off-by: Jennifer Williams <jennifer.m.williams@intel.com>
To ease maintenance of samples and tests some SoCs define
CONFIG_WDT_DISABLE_AT_BOOT=y to disable the watchdog. Ensure the option
is set to n for samples and tests that require watchdog module not to be
disabled during boot.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The test checks for a correct implementation if HWINFO_HAS_DRIVER
is set, otherwise it checks for -ENOTSUP return value.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Replace Kconfig configuration data with devicetree bindings using
(ADC) io channels. Rework the sample to document expectations about
the relationship between the reference voltage and the divider input
voltage, and update the sensor configuration to support Nordic SAADC.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace Kconfig configuration data with devicetree bindings using
(ADC) io channels. Rework the sample to document expectations about
the relationship between the reference voltage and the divider input
voltage, and update the sensor configuration to support Nordic SAADC.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The test case no longer permits inferring input and output pins based
only on the presence of GPIO aliases. Stop allowing presence of GPIO
aliases to enable the test.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Fixes a timeout failure on the frdm_k64f board.
test_short_relative_alarm iterates 100x through a 3 tick loop, but some
platforms like frdm_k64f have a 1 second counter tick period and
therefore need more time to finish this test.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Successful execution of this test requires a board-specific overlay to
identify the test pins, and that the test pins be shorted together.
Document this requirement.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Some boards don't support level interrupts; respect their rejection of
the configuration.
Also correct the code intended to disable the interrupt from within
the callback when level triggers are tested. Note that the legacy
call emulation does not work: it's necessary to add a flag that causes
the interrupt to be disabled.
Also improve a diagnostic and fix the exit path for a failure detected
before the callback was installed.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Added subsys argument to the callback, updated one driver which
used it and test cases.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Since the callback enable and disable functions are deprecated, but
cannot be re-implemented in terms of other API, add back an old-style
interrupt configuration test that uses the deprecated flags and
functions in the way existing code would do. The test module
internally disables the deprecation warnings.
Remove the test for the deprecated read/write functions, incorporating
a basic check into the module that tests deprecated callback functions.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested
only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
IO extenders may provide input signals to LEDs or sensors where
leaving the signal undriven may result in increased power consumption
or misbehavior. The SX1509B powers up with all signals configured as
inputs. Provide a way to indicate which pins should be set as output,
and their initial signal level, when the device is configured.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Previously the check would fail if a higher pin was present in the
callback set. Callbacks should only be told about pins that are
relevant to the callback, so reject unless exactly the expected pin
was provided.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Exclude the mps2_an385/mps2_an521 as we try to run on qemu and that
doesnt support the GPIO/LED so the tests will fail. For now exclude
the platform completely until we can just do a sim run exclusion.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- Updates gpio driver and device tree files to the new GPIO Config flags
- Implements the new port_* APIs
- Update I2C and PWM Drivers to use new GPIO config
- Add esp32.overlay to gpio_basic_api test
- refactor convert_int_type, regs struct
- remove config_polarity
- add kConfig notes
Tests:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_basic_api
- tests/drivers/gpio/gpio_api_1pin
Board:
- esp32 DevKitC V4
Note about interrupts:
The ESP32 requires specifying a CPU interrupt to be used for GPIO
interrupt signals. CPU interrupts can be either level or edge (or
special) triggered, but not both.
Please check gpio/Kconfig.esp32 for more info.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
Enables the 2-pin gpio test on the rv32m1_vega_ri5cy board by adding a
dts overlay and configuring pinmuxes on the arduino header.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
When checking the behavior of pull configurations delay long enough
for the signal to stabilize. Checking without a sufficient delay may
indicate a false failure.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The debounce flag is to be provided to the pin configuration, not the
pin interrupt configuration.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
LPC54114 to use D0 and D1 pinout.
LPC55S69 to use A0 and A1 pinout.
Pins enabled to be used as GPIO for 2 pin test gpio_basic_api.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
LPC54114 to use D0 and D1 pinout.
LPC55S69 to use A0 and A1 pinout.
2 pin test gpio_basic_api uses pins set up in boars' pinmux.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Keep promise of testing 1 pin only, don't attempt to test other pins
when verifying gpio_port_* API functions. Use BIT macro to create a bit
mask.
Fixes: #19692
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added configuration for the udoo_neo_full_m4 board and
the initialization of its GPIO test pins via IOMUX controller.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
The test verifies that the output pin appears to be shorted to the
input pin by confirming output low and high read low and high.
Failure should block progress through the test as subsequent tests
will not pass.
Replace the use of k_panic() to halt the test with an infinite loop
that doesn't splatter the console with stack traces and register
dumps.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Enables the 2-pin gpio test on the mimxrt1050_evk board by adding a dts
overlay and configuring pinmuxes on the arduino header.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adding overlays so that users can run this test on the following
boards:
- cc3220sf_launchxl
- cc3235sf_launchxl
- cc1352r1_launchxl
Instructions on pins to connect are included in the overlay files.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API.
Tested on external SX1509B breakout board and Thingy:52.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
A disconnected GPIO is one that is neither an input nor an output.
This is represented by a zero-valued all-default configuration. Call
this configuration GPIO_DISCONNECTED so the intent is clear.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The pull test assumed it was possible to configure the GPIO to be
disconnected. Some peripherals don't support a disconnected GPIO pin,
so if disconnected is not supported emit a note and attempt to
configure the output pin as an input.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Switch to gpio_pin_interrupt_configure() and the new interrupt flags.
Use logical level pin set operations. Test all standard interrupt
configurations including double edge.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Switch to gpio_pin_interrupt_configure() and the new interrupt flags.
Use logical level pin set operations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Test that the new port API functions all behave as expected, including
physical vs logical level for input and output as well as masked and
set-based output operations. Also tests the new pin API functions.
For running on real hardware this test now uses a local test-specific
devicetree binding. For build-only tests any platform with a GPIO
alias should be tested.
The new code increases flash requirements so add a filter to exclude
platforms that won't link.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
gpio_api_1pin testcase verifies following new GPIO API functionality:
- pin active level flags
- input/output configuration flags
- pin drive flags
- gpio_port_*, gpio_pin_* functions
- pin interrupts
The test is using only 1 GPIO pin (defined in DTS as LED0) and relies on
the ability of the driver to configure pin simultanously as in/out.
Drivers that do not allow to configure pins in in/out mode should still
pass the test, however, most of the testcases will be skipped.
The test does not require any modifications to board hardware.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Extends the keyboard scan callback row and column arguments from 8-bits
to 32-bits to support a touch panel driver implementation.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
test_single_shot_alarm_instance may fail due to not supported setting
of top_value in call to counter_set_top_value.
Modified to accept not supported case.
Fixes#21745
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Check for proper driver behaviour if timeout for uart_rx_enable or
uart_tx is set to K_FOREVER.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Teardown may fail due to not supported setting of top_value.
Modified to accept not supported case.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Introduce a new counter API function for reading the current counter
value (counter_get_value()) and deprecate the former counter_read() in
favor of this.
Update all drivers and calling code to match the new counter API.
The previous counter driver API function for reading the current value
of the counter (counter_read()) did not support indicating whether the
read suceeded. This is fine for counters internal to the SoC where the
read always succeeds but insufficient for external counters (e.g. I2C
or SPI slaves).
Fixes#21846.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
This commit introduces the can-primary alias to identify
the primary CAN interface.
This alias is used for all samples and tests, so they don't
need to probe the right interface.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
The pinmux_basic_api test relies on a hardware loopback, manual
shorting of two GPIO pins. The Zephyr test framework does not allow
currently to define such pins in a generic way. The pinmux_basic_api
test hard codes pin numbers specific to a few evaluation boards.
The test has a few more flaws and limitations:
- it verifies that pin configured to function A can be controlled by
GPIO driver. It doesn't verify that pin configured to function B can
be contorolled by a corresponding peripheral driver.
- the test relies on level sensitive interrupt support which is not
always available.
- the test will pass even if there are erros when pin is configured to
function B.
- the test allows to configure both test pins as an output therefore
shorting the outputs.
Considering the flaws and limited coverage of the test as well as
missing features of the Zephyr test framework this commit removes the
testcase. It is not currently possible to write a generic pinmux
testcase that supports multiple boards and can be used to assess the
quality of the driver. Instead, to ensure the driver code will not
degrade, we need to rely on implicit testing done by the board
initialization code located in boards/ folder.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Define a binding for the Bosch BMA280 sensor. Remove the Kconfig
settings and update the driver to use the devicetree information.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a single counter API test case (not using callbacks) running in
user mode. Convert the existing test setup to use semaphores for
counting events to be able to utilize the same test setup and teardown
functionality in both user and supervisor mode tests.
Most of the counter API basic test suite still needs to run in
supervisor mode due the use of callback functions.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
On nRF platforms, Xtal LF clock source starts hundreds of milliseconds.
Until it is not started, test may fail due to wrong timing. Add initial
delay in the test for required clocks complete their start-up.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Refactors the mcux rtc driver to use generated device tree macros
directly. Removes now unused dts fixup macros from kinetis socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
COUNTER_LOG_LEVEL (defined in
subsys/logging/Kconfig.template.log_config) is derived automatically and
has no prompt. Assignments have no effect on promptless symbols.
Set COUNTER_LOG_LEVEL_DBG=y instead, which corresponds to
COUNTER_LOG_LEVEL=4.
Flagged by https://github.com/zephyrproject-rtos/zephyr/pull/20742.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
We use a fixed value of 32 as the way interrupts/exceptions
are setup in x86_64's locore.S do not lend themselves to
Kconfig configuration of the vector to use.
HW-based kernel oops is now permanently on, there's no reason
to make it optional that I can see.
Default vectors for IPI and irq offload adjusted to not
collide.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add support for a eeprom simulator. The PR limits the addition to
qemu_x86 but it can easily be added to other devices by defining the
eeprom simulator in the dts and setting 'CONFIG_EEPROM_SIMULATOR=y'
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add a binding for the sensor and replace all Kconfig selection of
hardware parameters with devicetree property values.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add support for requesting an inverted PWM pulse (active-low) when
setting up the period and pulse width of a PWM pin. This is useful
when driving external, active-low circuitry (e.g. an LED) with a PWM
signal.
All in-tree PWM drivers is updated to match the new API signature, but
no driver support for inverted PWM signals is added yet.
All in-tree PWM consumers are updated to pass a flags value of 0
(0 meaning default, which is normal PWM polarity).
Fixes#21384.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Adds a board-specific configuration for the rv32m1 VEGAboard to the
spi_loopback test.
Enabled slave number 2, and turned on debug configurations to debug
effectively and from excess code being optimized out.
Signed-off-by: Jose Manuel Pacheco Luna <manuel.pacheco@nxp.com>
Define a binding for the Aosong DHT family of temperature/humidity
sensors. Remove the Kconfig settings, and update the driver to use
devicetree information.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
To get testing coverage after the fix in the previous commit.
Co-authored-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This patch enables SPI4 on the 96Boards STM32 Sensors Mezzanine.
SPI4 has been broken out to a Grove Connector on the board.
Changes:
- Updated board dts to enable spi4
- Updated board Kconfig
- Updated board documentation
- Update board pinmux
- Updated stm32f4 pinmux header file
- Updated stm32f401 dtsi
- Updated stm32f4 defconfig to enable PORTE GPIO
- Added board to spi_loopback test
Test: spi_loopback test passed
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Low frequency and high frequency clocks had separate devices
while they are actually handled by single peripheral with single
interrupt. The split was done probably because opaque subsys
argument in the API was used for other purposes and there was
no way to pass the information which clock should be controlled.
Implementation changes some time ago and subsys parameter was
no longer used. It now can be used to indicate which clock should
be controlled.
Change become necessary when nrf5340 is taken into account where
there are more clocks and current approach would lead to create
multiple devices - mess.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Adds board-specific configurations for the lpcxpresso54114 and
lpcxpresso55s69 to the spi_loopback test.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Some tests assume that the counters are always counting up
without regard to their capabilitiy bits. So fix the tests
if those counters are counting down.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The seasonal overhaul of test identifiers aligning the terms being used
and creating a structure. This is hopefully the last time we do this,
plan is to document the identifiers and enforce syntax.
The end-goal is to be able to generate a testsuite description from the
existing tests and sync it frequently with the testsuite in Testrail.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Also replace some
config
prompt "foo"
bool/int
with the more common shorthand
config
bool/int "foo"
See the 'Style recommendations and shorthands' section in
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
On watchdog-triggered reboot, the SAM platforms
reset RAM, so the wdt_basic_api cannot be completed
successfully, as it relies on RAM retention (relies
on variables stored in RAM retaining their values
across different boot cycles). Exclude the platforms
with the SAM Watchdog from this test.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Commit 555936f771 ("dts/Kconfig: Remove unused HAS_DTS_SPI")
accidentally removed the wrong #endif, meaning the second part of
dts_fixup.h depended on DT_ADXL372_DEV_NAME not being defined.
Discovered through the reference to the undefined HAS_DTS_SPI symbol in
the comment after the #endif at the end of the file. Adding detection of
unused symbols in samples and tests to CI.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit converts the existing hcm5883l 3-axis magnetometer
driver to use device tree for the I2C and GPIO selection.
It also adds a basic sample application for this sensor, using the
frdm-k64f development board to demonstrate how the interrupt
GPIO pin and I2C bus can be selected.
Signed-off-by: Kevin Townsend <kevin@ktownsend.com>
Update calls to nrfx HAL functions to reflect API changes introduced in
nrfx 2.0.0. All these functions are now called with the first parameter
pointing to the structure of registers of the relevant peripheral.
Also a few functions got renamed:
- nrf_gpiote_int_is_enabled to nrf_gpiote_int_enable_check
- nrf_gpiote_event_is_set to nrf_gpiote_event_check
- nrf_rng_event_get to nrf_rng_event_check
- nrf_rng_int_get to nrf_rng_int_enable_check
- nrf_rtc_event_pending to nrf_rtc_event_check
- nrf_rtc_int_is_enabled to nrf_rtc_int_enable_check
- nrf_timer_cc_read to nrf_timer_cc_get
- nrf_timer_cc_write to nrf_timer_cc_set
Default configuration values were removed from nrfx_config files,
so the drivers pwm_nrfx and spi_nrfx_spis no longer can use those.
Function nrfx_pwm_init() now takes one more parameter - context pointer
that is passed to the event handler, not used in the pwm_nrfx driver.
HALs for UART and UARTE now allow configuration of the parity type
and the number of stop bits, for SoCs that provide the corresponding
registers.
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert bmg160 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert bmm150 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert max44009 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert mcp9808 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert sx9500 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert tmp112 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert th02 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adding a Kconfig option for this test to configure the SPI in LOOP
mode. This saves physical wiring for hardware that support it.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Making CONFIG_SPI_ASYNC optional allows the test to be run on devices
where the feature is not yet supported in the driver.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Add EEPROM API test suite.
The test suite is written to run in userspace but it is currently only
whitelisted for native_posix and native_posix_64 boards which do not
support userspace.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Update the board overlays used in the i2c_slave_api tests to match the
new device tree bindings for atmel,at24 I2C EEPROMs.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This commit limits the data length code to eight.
DLC > 8 returns a newly introduced CAN_TX_EINVAL error code.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Replace CONFIG_WDT_0_NAME with DT_ALIAS_WATCHDOG_0_LABEL in samples and
test code. Now that all drivers are DT aware we don't ever set the
Kconfig option.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update lis3mdl-magn dts binding to include GPIO interrupt pin and change
driver code to get the GPIO pin and controller info from DT instead of
Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Previous defconfig for dma is DMA_STM32F4X in this board, while the new
generic driver uses DMA_STM32 to enable DMA support, and also dma driver
of stm32 now needs HEAP_MEM_POOL_SIZE to be big enough to hold dma
stream instances.
Additional .conf files are added for also adding HEAP_MEM_POOL_SIZE
configuration to two test cases.
Signed-off-by: Song Qiang <songqiang1304521@gmail.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
convert sample and test yaml filters that utilize a DT_ define to
instead use a dt_ function. The intent is to remove the Kconfig
generated DT defines and just make directy queries into the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Unused since commit f3f8f96842 ("tests: i2c_slave_spi: update to
proposed DT compatible naming").
Found with a script.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
According to the comment in #20008 I found out that some test cases
for different tests have same names.
To get rid of it, I decided to change test cases names.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Work in topic-gpio to convert drivers to properly use devicetree flag
settings requires that these be defined so sanitycheck can find them.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Re-run with updated script to convert integer literal delay arguments
to k_thread_create and K_THREAD_DEFINE to use the standard timeout
macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Re-run with updated script to convert integer literal delay arguments to
k_sleep to use the standard timeout macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Added test suite which performs sanity check on instances with
fixed-top feature enabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Added tests which verifies that:
- driver will detect when absolute alarm is set too late.
- short relative alarm is supported
- canceled alarm is not triggering user callback
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Implemented latest extensions to the counter API related to
detection of alarms being set too late and short relative alarms.
Implementation could not be realized on nrfx_rtc driver thus
driver has been reimplemented based on nrf_rtc hal.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Added test suite for clock control driver. It covers latest API update
for starting clock asynchronously and getting status.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Use the int_literal_to_timeout Coccinelle script to convert literal
integer arguments for kernel API timeout parameters to the standard
timeout value representations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Application board.overlay files tend to be paired with
boards/board.conf files that extend the functionality of a board.
Move the overlay files to the same location as the config files that
they work with.
A few overlay files that are paired with a prj_board.conf file in the
application root directory are left in place.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Removed unused peripheral tag and add drivers to
include test to drivers sanity check run.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Port the lis2mdl sensor driver on top of the lis2mdl_StdC
HAL interface (in modules/hal/st/sensor/stmemsc/).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
No users of this driver after dropping quark platforms.
COUNTER_0_NAME was only defined by the QMSI driver and was defined but
not used in DTS fixup files of ateml_sam0 SoCs. Removing those leftover
defines as well.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add support to STM IIS3DHHC the ultra-low noise, high-stability
three-axis linear accelerometer.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The LIS2MDL is not a combo device, but pure magnotemeter.
Hence, '-magn' extension is not adding information and can
be removed from dts compatible name as well as binding filename.
Instead specify '-i2c' or '-spi' to distinguish between the names.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
After the window watchdog introduction, the boards that support it over
independent watchdog fail to pass this test. This patch adds specific
tests for the nucleo_{f401re, l496zg} boards supporting WWDG.
Signed-off-by: Ioannis Konstantelias <ikonstadel@gmail.com>
This has been subsumed by the new implementation in drivers/pcie.
We remove the legacy subsystem, related tests, shell module, and
outdated documentation/config references.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
this case isn't designed for SMP, setting CONFIG_MP_NUM_CPUS=1 to
run the full SMP kernel config, but with only one CPU available.
Fixes: #12478.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
No test verifies a TX callback for successful transfers.
This commit adds a test for those callbacks.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
The mcux pwm drivers use period cycles as a divisor to calculate the pwm
frequency in hertz. This operation can underflow easily with large
values of period cycles relative to the pwm clock source, causing the
driver to return an error code and the pwm_api test to fail.
Updates the test to use the smaller set of period and pulse cycles on
k64-based boards, fixing the test for frdm_k64f and hexiwear_k64 boards.
The test is not changed for i.mx rt boards because the pwm clock source
on these boards is much faster than on k64 boards, and thus the same pwm
frequency operation does not underflow.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add SPI support for stm32mp157c_dk2 board. If SPI is selected, SPI4
(Arduino connector compatible SPI) and SPI5 (on front 2x20 GPIO
expander) will be enable by default on stm32mp157c_dk2 board.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
We generated a define for each instance to convey its existance of the
form:
#define DT_<COMPAT>_<INSTANCE> 1
However we renamed all other instance defines to be of the form
DT_INST_<INSTANCE>_<FOO>. To make things consistent we now generate a
define of the form:
#define DT_INST_<INSTANCE>_<COMPAT> 1
We also now deprecate the DT_<COMPAT>_<INSTANCE> form and fixup all uses
to use the new form.
Fixes: #17650
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
These additional configs should have been put in prj.conf
and not here. Makes the tests simpler to build correctly
outside of sanitycheck.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Flash size calculation was don with assumption that flash page size
is always 1 KB and flash size was parameterized with such granularity.
This patch correct this bug.
Flash pages number under statistic can't be calculated via preprocessor
anymore - thus are parameterized via Kconfig.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
It Need to start using DT_FLASH_SIM_xxx labels after sim_flash was
un-chosen as zephyr,flash.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Remove whitelisting and make the test more generic. This test was only
building on 1 board basically, now with the new filters it builds on 24.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Remove whitelisting and enable broader testing on all boards with needed
features.
Add pwm to board yaml where it applies.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
uint8_array values are now generated as structure initializers. Update
the code accordingly. The implementation assumes that existing
devicetree source does not provide the correct OUI so preserves the
in-driver override of the value provided by devicetree.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Flags in alarm configuration structure will allow further extention
without breaking API. Initially, existing absolute flag was added
as the only flag.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add support to STM LSM6DSO 6-axis IMU sensor driver.
This driver supports communication with device though both
I2C and SPI bus and both polling and drdy trigger mode.
This driver supports also the sensorhub mode with the possibility
to connect a maximum of two external devices, typically a
magnetometer and an environmental sensor, currently selected among
following devices: lis2mdl magnetometer, lps22hh or lps22hb
pressure and temperature sensors, HTS221 humidity sensor.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add support to STM LPS22HH pressure and temperature sensor.
The driver support I2C and SPI bus communication and both
polling and drdy trigger mode.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Tick rate is becoming a platform tunable in the tickless world. Some
apps were setting it due to requirements of drivers or subsystems (or
sometimes for reasons that don't make much sense), but the dependency
goes the other way around now: board/soc/arch level code is
responsible for setting tick rates that work with their devices.
A few tests still use hard-configured tick rates, as they have
baked-in assumptions (like e.g. "a tick will be longer than a
millisecond") that need to be addressed first.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/printk.h to sys/printk.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move uart.h to drivers/uart.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move spi.h to drivers/spi.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move rtc.h to drivers/rtc.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move pwm.h to drivers/pwm.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move pinmux.h to drivers/pinmux.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move ipm.h to drivers/ipm.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move i2s.h to drivers/i2s.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move i2c.h to drivers/i2c.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move hwinfo.h to drivers/hwinfo.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move flash.h to drivers/flash.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move entropy.h to drivers/entropy.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move dma.h to drivers/dma.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move counter.h to drivers/counter.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move clock_control.h to drivers/clock_control.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move can.h to drivers/can.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move aio_comparator.h to drivers/aio_comparator.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move adc.h to drivers/adc.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move watchdog.h to drivers/watchdog.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert DT_.*_GPIO_{CONTROLLER,PIN,FLAGS} ->
DT_.*_GPIOS_{CONTROLLER,PIN,FLAGS)
Used the following commands to make these conversions:
git grep -l DT_.*_GPIO_CONTROLLER | xargs sed -i 's/DT_\(.*\)_GPIO_CONTROLLER/DT_\1_GPIOS_CONTROLLER/g'
git grep -l DT_.*_GPIO_PIN | xargs sed -i 's/DT_\(.*\)_GPIO_PIN/DT_\1_GPIOS_PIN/g'
git grep -l DT_.*_GPIO_FLAGS | xargs sed -i 's/DT_\(.*\)_GPIO_FLAGS/DT_\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Port the lis2dw12 sensor driver on top of the lis2dw12_StdC
HAL interface (in modules/hal/st/sensor/stmemsc/).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
