This commit enables test_spi_loopback sample application for
Nucleo_F207zg. test_spi_loopback was executed under the following case
sceanarios on SPI-1:
a. With DMA
b. No DMA - No Interrrupts
c. No DMA - Interrupts Enabled
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
Enable by default the use of RAM buffers in the spi_nrfx_spim.c
driver for copying TX data located in flash (as SPIM peripherals
cannot transfer directly form flash). Without this patch, users can
get confused, especially when SPI transaction is used by an upper
level driver which does not check all error codes.
For size of the buffer, use the value used so far in the reel_board
default configuration and in the SPI loopback test, i.e. 8 bytes.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for running the SPI loopback driver test on the ARM
Cortex-M1 DesignStart FPGA reference design.
Since Xilinx AXI Quad SPI IP only supports loopback mode when configured
for single line SPI width, we utilise the (normally disabled) single SPI
instance going to the optional V2C DAPLINK shield SD card slot for
testing purposes.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Now that the patches have landed, enable more of the peripherals on
the board.
In particular:
* Enable PWM on the LED
* Enable the SPI, USB, and DMA
* Enable the bootloader support
* Add to the PWM and SPI tests
* Call these out in supported.yaml
Signed-off-by: Michael Hope <mlhx@google.com>
Due to issue #20589 DEBUG_OPTIMIZATIONS were enabled for the rv32m1 vega
ri5cy vega config. This is now resolved after making sure the spi tx
buffer is always initialized and the rv32m1 ri5cy core stack properly
initialized, so this workaround can be removed.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
Plus corresponding configuration file for the spi_loopback test that
will be activated for that board by this added capability.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This configures the nucleo_wb55rg board for testing
the SPI loopback with DMA MUX transfer.
This test requires pin SPI_A_MISO (D12) to be connected
to pin SPI_A_MOSI (D11) on the nucleo_wb55rg board
Signed-off-by: Francois Ramu <francois.ramu@st.com>
After increasing SPI speeds on LPC family SoCs, the slow clock
speeds have been removed and default clock speeds are in use now.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
This commit adds the SPI testing support with an internal MOSI to MISO
loopback for the Atmel SAM R21 Xplained Pro board.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the SPI testing support with an internal MOSI to MISO
loopback for the Atmel SAM E54 Xplained Pro board.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The STM32 and CC13xx/CC26xx SPI drivers don't utilize the Kconfig
symbols for per instance SPI anymore so we don't need to set them on the
conf files for this test.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This configures the nucleo_f411re board for testing the SPI loopback
with DMA V1 transfer. DMA instance 2 is used.
This test requires pin SPI_A_MISO (D12) to be connected
to pin SPI_A_MOSI (D11) on the nucleo_wb55rg boardtest dma_V1
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This configures the nucleo_l476rg board for testing the SPI loopback
when with DMA transfer.
It requires pin MOSI to be connected to pin MISO of the SPI1
SPI tx/rx are assigned to the request ID 1 of dma1 channels 3 and 2
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Don't assume in the soc level device trees that flexcomm nodes will
always be configured as spi. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The board name for the nRF52 DK, so far known as nrf52_pca10040, is
renamed to nrf52dk_nrf52832. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to
match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Kconfig options that enable I2C and SPI instances are no longer used
in nRF drivers. Remove all assignments done to these options in related
board definitions, samples, and tests.
For nrf52_pca20020, also no longer needed setting of default values
for GPIO_SX1509B* options is removed (now the gpio_sx1509b driver is
enabled by default when a corresponding devicetree node is enabled).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
We rename the nRF51 Dev Kit board target (nrf51_pca10028)
to nrf51dk_nrf51422. We update all associated references
in the supportive documentation and all nRF51-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Since commit 22326f6d99 got in, this test
requires that so-called NOP frames (bytes of value 0) are sent when no
TX data is provided. For nRF SoCs, the over-read character (ORC) that
is sent in such case is by default configured to the value of 0xFF.
Alter configurations for nRF boards so that 0x00 is used instead.
On the occasion, remove redundant selections of driver type in those
configurations (CONFIG_SPI_x_NRF_SPI[M]=y), as such selections must
be aligned with the value of "compatible" property in corresponding
nodes in dts, so there's no much sense in having them separately here.
Correct also the SPI instance to be used for nrf51_pca10028.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Adds a board-specific configuration for the rv32m1 VEGAboard to the
spi_loopback test.
Enabled slave number 2, and turned on debug configurations to debug
effectively and from excess code being optimized out.
Signed-off-by: Jose Manuel Pacheco Luna <manuel.pacheco@nxp.com>
This patch enables SPI4 on the 96Boards STM32 Sensors Mezzanine.
SPI4 has been broken out to a Grove Connector on the board.
Changes:
- Updated board dts to enable spi4
- Updated board Kconfig
- Updated board documentation
- Update board pinmux
- Updated stm32f4 pinmux header file
- Updated stm32f401 dtsi
- Updated stm32f4 defconfig to enable PORTE GPIO
- Added board to spi_loopback test
Test: spi_loopback test passed
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Adds board-specific configurations for the lpcxpresso54114 and
lpcxpresso55s69 to the spi_loopback test.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add SPI support for stm32mp157c_dk2 board. If SPI is selected, SPI4
(Arduino connector compatible SPI) and SPI5 (on front 2x20 GPIO
expander) will be enable by default on stm32mp157c_dk2 board.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add the Atmel SAM R21 Xplained Pro Evaluation Kit to zephyr.
So far, UART, SPI, I2C (depends on #14128), debug LED and user button
have been tested.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
The options selecting nRF drivers are now enabled by default when
an nRF SoC is selected as the build target.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
