OpenThread UART tx callback has been processed even if it was not
triggered by OpenThread otPlatUartSend function.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
Uses of k_work_pending are to be replaced by k_work_is_pending which
conforms to current proposed naming guidelines.
Switch to the new function.
Also initialize the private work structure at build time, rather than
on each iteration (it is not permitted to invoke work API on an
uninitialized work item).
The implementation here is racy: that a work item is pending does not
mean changes since it was first submitted are guaranteed to be seen
when the work item begins (began) executing.
A better solution would be to have transmit_message be able to
determine whether there is unprocessed work. Then the work item can
be submitted unconditionally.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Avoid splitting lines when possible while keeping length below 100
chars. Some other minor style corrections.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
The use of a single error variable for RX and TX operations has
shown the OpenThread code to be asserting in some conditions.
This commit splits tx_rx_result into rx_result and tx_result
to avoid such cases.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
* Added implementations of otPlatCAlloc and otPlatFree methods
necessary for the OpenThread in case of using EXTERNAL_HEAP.
* Added CONFIG_OPENTHREAD_DNSSD_SERVER option to allow enabling
OT_DNSS_SERVER feature.
Signed-off-by: Kamil Kasperczyk <kamil.kasperczyk@nordicsemi.no>
Remove `OPENTHREAD_CONFIG_NCP_BUFFER_SIZE` define since it does not
exist in OpenThread.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
During recent upmerge OPENTHREAD_CONFIG_PLAT_LOG_FUNCTION__COUNT_ARGS
macro was renamed to OPENTHREAD_CONFIG_PLAT_LOG_MACRO_NAME__COUNT_ARGS
but the code wasn't updated where the macro is actually used.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Add option to enable software CSMA backoff in the OpenThread MAC layer.
This allows to run CSMA procedure correctly in radios that do not
support hardware CSMA backoff, and use them as RCP, where this feature
is required.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This commit adds a missing otPlatSettingsDeinit function
to the Zephyr OpenThread platform implementation.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
If networking pre-emptive thread priorities are enabled,
then use the proper macro to enable them.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
* Add RCP library.
* Conditionally remove non required libraries not required for RCP.
* Drop :option: marker for CONFIG_OPENTHREAD_NCP_SPINEL_ON_UART_ACM
Signed-off-by: Markus Becker <markus.becker@tridonic.com>
These defines are leftover of old platform settings implementation
and are not used any more.
Signed-off-by: Lukasz Maciejonczyk <lukasz.maciejonczyk@nordicsemi.no>
Another team reported that current default values for number of allowed
IP addresses per child (4) and and max number of children (10) are too
small for some customers.
Increased the values allowed configuring child count.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
OpenThread mac counters require rx failed notification to work properly.
Made use of previously implemented notification.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
This commit adds additional Kconfigs that allow for changing
configuration values for the Zephyr port in OpenThread.
Those values are:
- number of the internal OT message buffers
- number of the state change callbacks
- number of the EID-to-RLOC cache entries
- size of the NCP buffer
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
Since commit b3a1ede830 OpenThread uses the Zepyhr settings submodule
instead of writing to the flash directly. The flash.c file is not
compiled anymore, so let's just remove it. Also remove the
OT_PLAT_FLASH_PAGES_COUNT Kconfig option which was solely used by that
file.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
OT_RADIO_CAPS_SLEEP_TO_TX was added as a radio capability
for ieee802154 radio. Waiting on RX state before transmission
is alternative condition to OT_RADIO_CAPS_SLEEP_TO_TX support
as it was a result of OpenThread architecture and is actually
not needed in the Zephyr. Such change lets to start transmission
faster and lower SED device power consumption in active state
about 30%.
Signed-off-by: Kamil Kasperczyk <kamil.kasperczyk@nordicsemi.no>
Zephyr platform does not support MAC retransmissions on its own,
so OT_RADIO_CAPS_TRANSMIT_RETRIES capability was removed.
It should not be enabled basing on IEEE802154_HW_CSMA support,
as these are quite seperate features. Current implementation
assumes that platform performs retransmissions on its own,
what is not provided and leads to lack of MAC retransmissions.
Signed-off-by: Kamil Kasperczyk <kamil.kasperczyk@nordicsemi.no>
Currently, OpenThread builds produce warning from the OT logger module,
because we don't use one of the parameters provided by logger macro.
Explicitly mark the parameter as unused to prevent warnings being
thrown.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Putting data to local buffer before transmission was removed
to optimize operation. Local buffering was not needed, as passed
buffer cannot be modified until sending is finished.
Signed-off-by: Kamil Kasperczyk <kamil.kasperczyk@nordicsemi.no>
Fix compilation error when the DIAG module is enabled.
All core functionalities are provided.
Signed-off-by: Piotr Szkotak <piotr.szkotak@nordicsemi.no>
Unit tests were failing to build because random header was included by
kernel_includes.h. The problem is that rand32.h includes a generated
file that is either not generated or not included when building unit
tests. Also, it is better to limit the scope of this file to where it is
used.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
OpenThread API is not thread-safe.
Moved creation of otMessage to the Thread task and created api
for passing it properly.
This way it should be less possible for an issue to occure eg.
during message buffer allocation.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
Added automatic strdup for RAM %s parameters. Postponed format
processing to idle time. Automatic parameters counting during
compilation. Very fast execution for up to three parameters.
Signed-off-by: Tomasz Konieczny <tomasz.konieczny@nordicsemi.no>
This PR enables the user to configure the maximum command length for
OpenThread's CLI using Zephyr's shell, which is currently fixed to
256 characteres. This limitation was not enough for certain allowed
OpenThread commands, like some variants of 'ot dataset mgmtsetcommand'.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
OpenThread moved from 4 to 5 debug levels and it was not possible
to configure all of them with Kconfig.
Signed-off-by: Eduardo Montoya <eduardo.montoya@nordicsemi.no>
Replace:
DT_FLASH_ERASE_BLOCK_SIZE ->
DT_PROP(DT_CHOSEN(zephyr_flash), erase_block_size)
DT_FLASH_WRITE_BLOCK_SIZE ->
DT_PROP(DT_CHOSEN(zephyr_flash), write_block_size)
As this allows us to phase out the old generator.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace DT_FLASH_DEV_NAME with DT_CHOSEN_ZEPHYR_FLASH_CONTROLLER_LABEL.
We now set zephyr,flash-controller in the chosen node of the device
tree to the flash controller device.
NOTE: For a SoCs with on die flash, this points to the controller and
not the 'soc-nv-flash' node. Typically the controller is the
parent of the 'soc-nv-flash' node).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Set information about Frame Pending Bit from the ACK response in the
frame passed to OpenThread.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Replace CONFIG_ENTROPY_NAME with DT_CHOSEN_ZEPHYR_ENTROPY_LABEL. We now
set zephyr,entropy in the chosen node of the device tree to the entropy
device.
This allows us to remove CONFIG_ENTROPY_NAME from dts_fixup.h. Also
remove any other stale ENTROPY related defines in dts_fixup.h files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fill the mTimestamp filed in OpenThread frame based on the net_pkt
timestamp value (only if NET_PKT_TIMESTAMP is enabled).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Received frames shall be handled in the OpenThread thread, not in
the receiver thread.
Passed received frame to the function that will handle it in a proper
thread instead of calling otPlatRadioReceiveDone directly.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
OpenThread received frame handling shall be done in the OpenThread
thread.
Created API to pass net packets to the proper thread and handle them
there.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
