Instead of silently closing the link we should send a Link Close message
three times before resetting provisioning state.
From Mesh Profile Specification v1.0.1.:
```
5.3.1.4.3 Link Close message
The Link Close message is used to close a link.
```
```
5.3.2 Link Establishment procedure
The device shall start the link timer, set to 60 seconds, when the link
is open. When the link timer expires, then the device shall close the
link.
```
```
5.3.3 Generic Provisioning behavior
If the sender does not receive a Transaction Acknowledgment message
within 30 seconds after sending the first message in a transaction,
the sender shall cancel the transaction, cancel the provisioning
process and close the link.
```
From Mesh Profile Test Specification p6:
```
MESH/PVNR/PBADV/BV-01-C
Test Procedure:
[...]
6. The IUT is induced to send a Link Close message with the Reason field
set to 0x02 to terminate the link. The message is sent at least three
times to ensure the message is received by the Lower Tester.
```
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Adds support for extended advertiser commands in the mesh. This doubles
throughput for common packet sending, and significantly improves timing
accuracy for the Friend and Low Power features.
The proxy module's advertisement control has been moved inside the adv
module to abstract away the different advertiser modes.
The extended advertiser mode does not need an advertising thread to
operate, and ends up with a net reduction in RAM usage.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Wrong use of function `find_msb_set(~link.rx.seg)`,
uint8_t type is implicitly converted to uint32_t.
As a result, it always returns 32 instead of the
expected value, resulting in abnormal processing
of prov segment.
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
Currently all provisioning procedure into common source
files call `prov.c`, that will not compile separately.
Add `BT_MESH_NODE` to control whether nodes are supported
and device provisioning is supported, this will be used in
provisioner role.
Add more provisioner OOB authentication method.
Signed-off-by: Lingao Meng <mengabc1086@gmail.com>
Reset provisioning bearers when bt_mesh_reset() is called. Accept
another provisioning attempt after link close.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
This value was used quite often in the file so adding a
descriptive name should improve readability.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
The comparison of a current tx link transaction id caused
us to not send ack and in effect fail provisioning.
Signed-off-by: Michał Narajowski <michal.narajowski@codecoup.pl>
Convert bluetooth mesh to using k_timeout struct. Many of the mesh
modules uses timeout calculations, so it is most practical to keep
the s32_t type and only initialize a k_timeout_t struct when
calling the kernel.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Splits PB-ADV and PB-GATT into separate modules with a common interface
to modularize prov.c.
Additional trivial fixes from testing:
- Reduces warnings for normal occurances like repeated packets.
- Makes link ack a non-reliable packet to prevent it from being repeated
until prov invite.
- Provisioner does not send link fail, but closes the link (as per spec
section 5.4.4). This prevents lingering zombie links on both sides.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
