Only 1 TX buffer is sub-optimal for performance since the controller
would always have to wait for the host TX thread to give it another
buffer. Increase the value to 2 so the controller can keep
transmitting data without waiting for the host.
Change-Id: I4841a6c5010f294996d6fe0fe63260b848a6a437
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since this presents a risk of public Bluetooth address duplication in
the wild by compiling once with a particular address and then flashing
the same image to multiple devices, a decision has been taken to remove
that config option and replace it later with another mechanism.
Change-Id: I068db25b2996c2409630554b1819b6adc48226cd
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In preparation for future hardware implementations of the BLE
Link Layer, this patch introduces the BLUETOOTH_LL_SW
configuration option to specify that the default software
LL is to be built.
Change-Id: I8b9d5b5e0d2926d18f9e8c8f042a74326895bf95
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Bluetooth device address is 48-bit, added Kconfig range
field to restrict input to 48-bit hexadecimal value.
Change-id: I650343eab5809535137e164e783c9dd4f3e2a6f2
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add Kconfig option to set the Controller's company id and
subversion number.
Change-id: I3508aba18bf0b79fd423c7b4142b6fc57eaf55d7
Signed-off-by: Matthias Ringwald <matthias@bluekitchen-gmbh.com>
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add a Controller event that indicates everytime
advertisement event has been transmitted on air.
Change-id: I4722488bbfeca987e66983faf5b26467407a89c9
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Added Kconfig option to be able set public address. Seems
conformance testers look for valid public address.
Change-Id: I2c4f702117f99a42c9eef0133b46556a1c6d1496
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
A new Kconfig debug option now controls the usage of pin toggling to
debug the BLE controller.
Change-Id: I24c5c13ca71e3395e10f14e27ad4bca9f2e94687
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
For the host to be able to block on the recv_thread while waiting for a
number of completed packets HCI event, those are pulled from the radio
in a new, higher priority thread that also schedules the execution of
the lower priority event/ACL data recv_thread.
Change-id: I9d356bd297d0504cb16a032fb5fe5530693546e2
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Since the controller already uses a thread for receiving data it makes
sense to enable the BLUETOOTH_RECV_IS_RX_THREAD option.
Change-Id: I927b20c1a0afaea8d000df28cc220a69ae817d59
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Enable connection encryption setup in 3 connection
intervals. Peripheral will respond to Encryption Request
with Encryption Response in the same connection interval,
and also, will respond with Start Encryption Response PDU in
the 3rd connection interval, hence completing encryption
setup in 3 connection intervals. Encrypted data would be
transmitted as fast as in 3rd connection interval from the
connection establishment. Maximum CPU time in Radio ISR will
increase if this feature is selected.
Change-id: I16f2863fc2aaed624826505739519d4de1ac44c5
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add Kconfig configuration to select Tx buffer size, this
value will be returned in the HCI LE Read Buffer Size
command response.
This configuration will allow lower Tx RAM usage when
larger PDU sizes are desired in Rx direction only.
Change-Id: I5106a448d78a0754c4b0f6fa61fd5dcacd87a67c
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add Kconfig configuration and conditional compilation of
RSSI measurement during a connection.
Change-id: I5a2f23f76a7cbbd9569d53d31899a472bf39d3ee
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
Add Kconfig configuration to conditionally enable Data
Length Update procedure support in the Controller.
This will save CPU time, flash and RAM, if this feature is
not desired.
Change-id: I4515c0c7cf9aeb333a289397ae3c9bac04a08e4e
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The following readings were obtained after running the peripheral and
central_hr apps in qemu combined with the controller (hci_uart) on nRF51
and nRF52:
Main Stack 380
Idle Stack: 68
ISR stack: 532
Controller RX Stack: 388
HCI TX Stack: 516
The numbers set in this change provide a safety margin from the ones
measured empirically.
Change-id: Ice7ad7f081502e0ea1accf856a7937c0bf0783b2
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add Kconfig configuration to conditionally enable LE Ping
feature in the Controller.
This will save CPU time, flash and RAM, if this feature is
not desired.
Change-id: I5fbbdbe8f45ac01c9b0d7b11e002a0d1db4d272e
Signed-off-by: Vinayak Chettimada <vinayak.kariappa.chettimada@nordicsemi.no>
The conditional defaults must come last in order to be properly
processed.
Change-Id: Id7a152ca1a1584935029e212d0dd8f37494d1cf4
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Switch from fiber_start() to k_thread_spawn() and from NANOKERNEL to
POST_KERNEL init level.
Change-Id: I34fb11cbe20216c8646ebacb07be304a67e3cd0a
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Currently the ideal buffer counts for a controller-only build are 6 RX
buffers and 7 TX buffers: ATT_MTU of 158 bytes can be sent in one
connection interval of 6 tx/rx -es wherein connection interval is
7.5ms
Change-Id: I64b4620c5e8e7db8d7ed72fa1db82e266e121f27
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Restructure the Bluetooth options more logically.
- Both host and controller are now behind the same high level
CONFIG_BLUETOOTH.
- Selecting controller support disables other HCI driver selection, so
the controller isn't in the same list as HCI drivers any more.
- Under the top-level there's a "Custom stack" option, which when
enabled opens up the option of choosing CONFIG_NBLE.
There are various other cleanups and simplifications in this patch as
well, since splitting these up would have been fairly tricky while
making sure all test cases still build.
Change-Id: I5bb715cb9d20201cb8b72fbd149c8a09a4b2d7d2
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When building Zephyr in the controller-only configuration,
assertions that happen in the Link Layer code are not visible
to the Host which is running on another HCI and connected via
UART or USB to it. This patch allows the Controller code
to output the assertion line number when in such a configuration,
allowing the Host to view the event to help debugging.
The event format used is temporary and will be replaced by a
standardized Vendor Specific specification to come at a later
time.
Change-Id: I013ca6783a3fdedc47b171132919dd4798c66285
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The right convention for help text is tab + 2 spaces.
Change-Id: I2722a8b33f5f74be110dc43fbcecc12841f0db84
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Move controller code from drivers/controller to
subsys/bluetooth/controller.
Change-Id: I73f675188485aa3267507bad7647796e593a3da0
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
