This patch removes sdhc_api references since such API
does not actually exist. SD card controller drivers
use disc driver interface. Accordingly, the SDHC documentation,
which actually describes how to connect a SD card via SPI
and has little to do with SD host controller (SDHC),
is also moved to disk access page and adapted.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Zephyr already has a directory for storage API relevant headers.
Move disk_access.h header to include/storage where it fits better
structurally.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Remove SPI_[0-8] and SPI_[0-8]_OP_MODES Kconfig symbols as no driver
uses them anymore. We also cleanup board and sample code to remove
use of these symbols.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The commit adds initializations of fs_dir_t variables in preparation
for fs_opendir function change that will require fs_dir_t object, passed
to the function, to be initialized before first usage.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
The commit adds initializations of fs_file_t variables in preparation
for fs_open function change that will require fs_file_t object, passed
to the function, to be initialized before first usage.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Extend the nrf52840dk_nrf52840 sample overlay with a fstab entry for a
littlefs file system on the storage partition.
This eliminates the need for application configuration of the file
system parameters and mount data.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Enables the fat_fs sample on the mm_swiftio board by adding a
board-specific Kconfig overlay, and adding sdhc to the list of
board-supported features.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The legacy macros were first deprecated in Zephyr v2.3. Now that
Zephyr v2.4 has been released, that makes two releases where these
macros have been deprecated, so it's OK to remove them.
This leaves support for legacy binding syntax in place. Removing that
is left to future work.
We need to update various pieces of documentation related to flash
partitions that never got updated when the new API was introduced.
Consolidate this information in the flash_map.h API reference page,
since that's really where users will run into it. This also gives us
the opportunity to improve this documentation.
Adjust a couple of kconfigfunctions.py and sanitycheck bits to use
non-legacy edtlib APIs.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The fs_open has been extended with support for open flags.
Currently supported flags are:
FS_O_READ -- open for read
FS_O_WRITE -- open for write
FS_O_CREATE -- create file if it does not exist
FS_O_APPEND -- move to the end of file before each write
The FAT FS and LittleFS front-ends within the Zephyr has also been
modified to utilize the flags.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
In fat_fs example, if we choose a large size SD card to connect with,
the result of memory size calculation coule be wrong due to the missing
brace for manipulating operator priority.
Fixes#26266.
Signed-off-by: Jui-Chou Chung <jui-chou.chung@nordicsemi.no>
This provides a better error message when building with CMake and
forgetting ZEPHYR_BASE or not registering Zephyr in the CMake package
registry. See parent commit for more details (split from parent for
better readability).
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Convert with a combo of scripts and by hand fixups:
git grep -l DT_FLASH_AREA_.*_ID | \
xargs sed -i -r 's/DT_FLASH_AREA_(.*)_ID/FLASH_AREA_ID(\L\1)/'
git grep -l DT_FLASH_AREA_.*_OFFSET | \
xargs sed -i -r 's/DT_FLASH_AREA_(.*)_OFFSET/FLASH_AREA_OFFSET(\L\1)/'
git grep -l DT_FLASH_AREA_.*_SIZE | \
xargs sed -i -r 's/DT_FLASH_AREA_(.*)_SIZE/FLASH_AREA_SIZE(\L\1)/'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Updates the fat_fs sample documentation to reflect that it can run on
multiple boards, not just the nrf52840_blip.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the fat_fs sample yaml to depend on a feature rather than
whitelisting specific boards. This implicitly extends the sample to
mimxrt10{60,64}_evk boards, since they already support the feature.
The only whitelist board remaining is the nrf52840_blip, which requires
a device tree overlay for this sample.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the fat_fs sample to move board-specific configurations to
separate files and support a shared prj.conf file.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The API call to close the flash area was only invoked when the flash
area was erased. It should be closed in all paths.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Using find_package to locate Zephyr.
Old behavior was to use $ENV{ZEPHYR_BASE} for inclusion of boiler plate
code.
Whenever an automatic run of CMake happend by the build system / IDE
then it was required that ZEPHYR_BASE was defined.
Using ZEPHYR_BASE only to locate the Zephyr package allows CMake to
cache the base variable and thus allowing subsequent invocation even
if ZEPHYR_BASE is not set in the environment.
It also removes the risk of strange build results if a user switchs
between different Zephyr based project folders and forgetting to reset
ZEPHYR_BASE before running ninja / make.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This is joint work with Kumar Gala (see signed-off-by).
Document the changes to the generated node macros in macros.bnf,
moving the old file to legacy-macros.bnf and putting it in its own
section.
The actual generated macros are now a low-level detail, so rewrite the
foregoing sections as examples in terms of the new <devicetree.h> APIs.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Name all subsystem reference consistently with an '_api' postfix and
clean up naming and folder structure in some cases.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Converts the sdhc spi driver to the new gpio api. Updates device trees
for the olimexino_stm32 and nrf52840_blip boards to set appropriate
active high/low polarity for the spi chip select pin.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adjust the configuration file, disable the SPI
driver and enable the QSPI driver and flash node.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Signed-off-by: Kamil Lazowski <Kamil.Lazowski@nordicsemi.no>
A configuration file attempted to select the external flash memory for
this platform, but there was no overlay that redefined the storage
partition to be on that device rather than the SOC flash.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The $srctree environment variable is already set to point to the Zephyr
root, so no need to do
source "$(ZEPHYR_BASE)/Kconfig.zephyr"
in samples. Just
source "Kconfig.zephyr"
works.
(Things would break if $srctree was set to anything else, because every
'source' in the Kconfig files will be relative to it.)
Also add a 'mainmenu' title to the littlefs sample. It shows up at the
top of menuconfig/guiconfig. Source Kconfig.zephyr instead of Kconfig to
avoid overriding it.
As a sidenote, $(FOO) is better $FOO in Kconfig. $FOO is legacy syntax
that Kconfiglib only supports to be compatible with old Linux kernels.
$(FOO) uses the Kconfig preprocessor.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The seasonal overhaul of test identifiers aligning the terms being used
and creating a structure. This is hopefully the last time we do this,
plan is to document the identifiers and enforce syntax.
The end-goal is to be able to generate a testsuite description from the
existing tests and sync it frequently with the testsuite in Testrail.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Configures the default instance of the sdhc driver for the
mimxrt1050_evk board so applications don't have to configure it
explicitly. Similarly, enables the gpio instance required by the sdhc
driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Configures the default sdhc driver for the imx rt soc series so
applications don't have to configure it explicitly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Configures the default sdhc disk volume name to "SD" when fatfs is
enabled. This prevents applications from having to configure it
explicitly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Re-run with updated script to convert integer literal delay arguments to
k_sleep to use the standard timeout macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Application board.overlay files tend to be paired with
boards/board.conf files that extend the functionality of a board.
Move the overlay files to the same location as the config files that
they work with.
A few overlay files that are paired with a prj_board.conf file in the
application root directory are left in place.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
There's desire to be able to customize parameters on a per-filesystem
basis, which means we need a way to override the Kconfig defaults which
are global. This also means the littlefs data structure cannot own the
cache and lookahead buffers.
Switch to using a macro to define the littlefs data structure. The
default version uses the Kconfig constants. A custom one takes
arguments providing the most likely partition-specific parameters.
Finally the user is free to bypass the helper macros and set any
parameters desired, though validation is limited and only present when
CONFIG_DEBUG is enabled.
Extend the test suite with a performance module, which confirms that
these settings have an impact proportional to the log of changes to the
cache or IO sizes.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The name disk_access_sdhc.c is ambiguous,
actually this driver depends on SPI,
rename this file.
In addition, move the generic sdhc stuff from C file
to head file for other sdhc drivers to use.
1) disk_access_sdhc.c->disk_access_spi_sdhc.c.
2) create .h and move sdhc specifications from .c to .h.
Signed-off-by: Jun Yang <jun.yang@nxp.com>
