Use a combination of fixed-clock and fixed-factor-clock devicetree
nodes for describing the clock dividers/multipliers of the NXP Kinetis
System Clock Generator (SCG) present in the KE1xF SoC series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Support single mode operation by enabling it and
making the driver to use the interrupt to findout
when the data is ready for fetch. The sample fetch
will be blocked for a specified maximum time untill
the interrupt happens.
* Make operation mode configurable in DTS file
* Make offset cancellation configurable in DTS file
* Use single common .yaml file for both i2c and spi
* Store above configurations in dev->config_info
Signed-off-by: Masoud Shiroei <masoud.shiroei@assaabloy.com>
This CL introduces the Power Switch Logic (PSL) pads which detect the
wake-up events and turn on/off core power supply (VCC1) for ultra-low
-power consumption in npcx device-tree file.
By adding PSL input-pad objects, psl_in1, psl_in2, and so on, into
'psl-in-pads' property and configuring their 'flag' properties, the
related driver will configure them via soc specific functions later.
For example, if PSL input 1 pad that is plan to detect a 'falling edge'
event, this property should be:
vsby-psl-in-list {
psl-in-pads = <&psl_in1>;
};
And the flag property in psl_in1 should change to
&psl_in1 {
flag = <NPCX_PSL_FALLING_EDGE>;
};
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Make sure that child bindings with their own compatibles are treated
as first-class bindings. Do this by making sure that nodes whose
bindings are defined via 'child-binding:' are picked up as bus nodes,
instead of a parent bus node of the same type.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The AN547 is a Soft Macro Model implementation of the SSE-300 subsystem
with Ethos-U55 and Cortex-M55 components targeting the MPS3 board.
The SoC support is based on the AN521 MPS2+ support that already exists
in Zephyr.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add initial support for the Cortex-M55 Core which is an implementation
of the Armv8.1-M mainline architecture and includes support for the
M‑profile Vector Extension (MVE).
The support is based on the Cortex-M33 support that already exists in
Zephyr.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
UARTs in Nordic devices only support a specified list of baud rates.
Choosing a different baud rate without this patch will cause a runtime
error, whereas with the constraint, this mistake is already found in
dts construction with a useful error message.
Signed-off-by: Peter Niebert <peter.niebert@univ-amu.fr>
This patch includes initial support for FT800 display driver.
It includes basic features. It can be easily extended with more
FT800 display list and co-processor features.
Signed-off-by: Hubert Miś <hubert.mis@gmail.com>
Add support to control DE/nRE RS-485 transceiver signals
over GPIO pins. Useful if the UART controller does not
support RS-485 mode.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Add MODBUS RTU (over serial line) subsystem.
MODBUS RTU implementation supports booth server and
client roles. Some components of the implementation are based
on the uC/Modbus stack, which was published under Apache license,
(https://github.com/SiliconLabs/uC-Modbus
fdd1218a28e313c1212fed5ed42e5c65d3056a2c).
Resolves: #2854
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
In NPCX chips, System Configuration module can configure not only
pinctrl but also misc. functionality such as glue and flash write
protection. This change moves the scfg driver from the pinctrl folder
to soc/arm/nuvoton_npcx/common and renames it to avoid confusion.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Adds support for the Texas Instruments FDC2X1X Capacitance-to-Digital
Converter for Proximity and Level Sensing Applications.
Signed-off-by: Igor Knippenberg <igor.knippenberg@gmail.com>
Introduce PSoC-6 pinctrl infraestructure and definitions. This add
files to handle devicetree entries and following modifications:
- add pinctrl bindings
- update gpio bindings with pin-cells
- add pinctrl node and move gpio nodes inside
- declare pinctrl for current uart entries
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Added file with common properties for cortex-m cores.
Added optional swo-ref-frequency property.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add GPIO definitions to QuickLogic EOS S3 devicetree.
Co-authored-by: Jan Kowalewski <jkowalewski@antmicro.com>
Signed-off-by: Wojciech Tatarski <wtatarski@antmicro.com>
Signed-off-by: Jan Kowalewski <jkowalewski@antmicro.com>
AArch64 has support for PSCI. This is especially useful for SMP because
PSCI is used to power on the secordary cores.
When the PSCI driver was introduced in Zephyr it was designed to rely on
a very PSCI-centric subsystem / interface.
There are two kinds of problems with this choice:
1. PSCI is only defined for the non-secure world and it is designed to
boot CPU cores into non-secure state (that means that PSCI is only
supposed to work if Zephyr is running in non-secure state)
2. There can be other ways or standards used to start / stop a core
different from PSCI
This patch is trying to fix the original wrong assumption by making the
interface / subsystem a generic one, called 'pm_cpu_ops', and using PSCI
only as an actual driver that is a user of this new interface /
subsystem.
For now the new subsystem is only exposing two methods: cpu_on and
cpu_off, others will probably follow according to the needs.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
The DMA bindings had duplicate description: keys. Merge the two
descriptions into one to fix the issue.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Many data items that are represented in a pin configuration node are
common and generic. Pin control bindings should use the properties
defined on a standard way when are applicable; not all of these
properties are relevant or useful for all hardware or binding
structures. Each individual binding document should state which of
these generic properties, if any, are used, and the structure of the
DT nodes that contain these properties.
This is based on Linux, documentation:
https://www.kernel.org/doc/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Conver the NIOS-II mSGDMA driver to be devicetree based. Add node for
dma controller into nios2f.dtsi.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Deprecate the scl-pin and sda-pin properties in the devicetree.
Provide new scl-gpios and sda-gpios properties instead.
This lets the user specify SCL and SDA like this:
&i2c0 {
scl-gpios = <&gpio0 1 0>;
sda-gpios = <&gpio1 4 0>;
};
Instead of having to use:
&i2c0 {
scl-pin = <1>;
sda-pin = <36>;
};
Provide error checking and understandable error messages for invalid
configurations.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Convert ism330dhcx INT_PIN attribute from Kconfigs to Device
Tree binding properties. Here int-pin has been defined as
enum with two possible values: 1 and 2.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert ism330dhcx accel and gyro odr attributes from Kconfigs to Device
Tree binding properties.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Converts ism330dhcx accel and gyro range attributes from Kconfigs to
Device Tree binding properties.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Create a common properties file that will be included by all bindings
(as i2c and spi) handled by ism330dhcx driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Change dfe-ant-num propert name to dfe-antenna-num.
The change is conde to keep the same naming style
for all properies, like dfe-pdu-antenna property.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
Add initialization of GPIOs that are used for antenna switching.
GPIOs provided to DFE extension in Radio peripheral, to drive
antenna switching, should be initialized in GPIO peripheral beforehand.
The initialization is optional and may be disabled by Kconfig.
Signed-off-by: Piotr Pryga <piotr.pryga@nordicsemi.no>
In NPCX7 series, it contains two tachometer (TACH) modules that contains
two Independent timers (counter 1 and 2). They are used to capture a
counter value when an event is detected via the external pads (TA or
TB).
The CL also includes:
— Add npcx tachometer device tree declarations.
— Zephyr sensor api implementation for tachometer.
— Enable "tach1" device in npcx7m6fb.dts for testing.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL introduces a kernel device driver implemented by the internal
64/32-bit timers in Nuvoton NPCX series. Via these two kinds of timer,
the driver provides an standard "system clock driver" interface.
It includes:
- A system timer based on an ITIM64 (Internal 64-bit timer) instance,
clocked by APB2 which freq is CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC.
- Its prescaler is set to 1 and provide the kernel cycles reading
without handling overflow mechanism.
- A event timer based on an ITIM32 (Internal 32-bit timer) instance,
clocked by LCLK which frequency is 32KHz and still activated when ec
entered "idle/deep idle" power state for better power consumption.
- Its prescaler is set to 1 and provide timeout event mechansim.
- Compensate system timer which clock is gating for better power
consumption after ec left"idle/deep idle" power state.
This CL passed starve, timer_api, and timer_monotonic test suites.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Modifications to incorporate latest write to new flash area
Modification to avoid writing garbage to new flash area when compactor
is called during init.
Modifications to allow erase at partition size instead of eeprom
pagesize.
Modifications to better separate rambuf usage from flash usage.
Corrected some errors in compactor
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
This driver emulates a EEPROM device in flash.
Reworked implementation with modified flash layout.
The emulation represents the EEPROM in flash as a region that is a
direct map of the eeprom data followed by a region where changes to
the eeprom data is stored. Changes are written as address-data
combinations. The size of such a combination is determined by the
flash write block size and the size of the eeprom (required address
space), with a minimum of 4 byte.
The eeprom page needs to be a multiple of the flash page. Multiple
eeprom pages is also so supported and increases the number of writes
that can be performed.
The eeprom size, pagesize and the flash partition used for the eeprom
are defined in the dts. The flash partition should allow at least two
eeprom pages. For fast read access a rambuffer can be enabled for the
eeprom (by setting the option rambuf in the dts).
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
We've removed the need for label properties from the pinmux devicetree
nodes on all other controllers and its not required for the TI one, so
remove it from the .dts and drop label being required in the binding.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Switch to use DEVICE_DT_GET instead of device_get_binding for pinmux
device. As part of this change drop the "label" property from
the pinmux devicetree node and update the binding and dts files to
reflect that.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
