Add SPI driver for the Xilinx AXI Quad SPI IP. Despite the name, this IP
block supports both single, dual, and quad line widths.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Using SPIM_FREQUENCY_FREQUENCY_M32 to check if the device has HS-SPI and
able to use higher SPI clock than 8MHz.
Signed-off-by: Jui-Chou Chung <jui-chou.chung@nordicsemi.no>
Flexcomm's SPI SSEL (or CS) will be held until frame end.
FIFOWR[EOT] (kSPI_FrameAssert enum) is the register not set.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
To keep the bus fully loaded, the SAM0 has a fast path that recognises
special cases like TX only, RX only, or TX/RX of the same size.
Commit #ea2431f32f7 accidentally disabled this.
This increases the utilisation from around 30 % to around 90 % at 48
MHz.
Signed-off-by: Michael Hope <mlhx@google.com>
The SAM0 has a data register and a shift register. Data that is
written to the data register is transferred to the shift register by
the peripheral.
On the SAMD51, the CPU is fast enough that the first data write hasn't
been transferred to the shift register by the time the next data write
occurs, causing the second write to be dropped, causing the receiver
to wait forever.
Fix by spinning until the data register is empty.
Signed-off-by: Michael Hope <mlhx@google.com>
Adds optional device tree properties to set delays between spi chip
select assert/deassert and clock edges in the mcux dspi and lpspi
drivers. If these properties are not set, then the minimum supported
delays are used.
Verified that tests/drivers/spi/spi_loopback/ still passes on
mimxrt1050_evk (lpspi driver) and frdm_k64f (dspi driver).
Measured with a scope that the pcs-sck-delay and sck-pcs-delay times on
the first spi transaction in the test are reduced from 7.82 us to 20 ns
on mimxrt1050_evk.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add an additional option to the spi_cs_control struct that records how
the pin has been configured in devicetree. For drivers that are not
updated, the CS behaviour is the same as before (Push-Pull).
Use the devicetree knowledge with the GPIO subsystem so that the correct
physical pin levels for the CS pin are automatically selected.
Fixes#26267
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Initialize the dummy data transfer so spi transfer is defined even for
an undefined tx data buffer. This aligns the rv32m1 spi driver with the
mcux spi driver.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
The consequent and alternate expressions for COND_CODE_1 must be
enclosed in parentheses, like this:
COND_CODE_1(PREDICATE, (consequent), (alternate))
The parens are missing in exactly one place in the tree. Fix it.
Reported-by: Peter Bigot <peter.bigot@nordicsemi.no>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The power configuration is dependent on which SPI is physically used.
In order to allow DT_INST_FOREACH_STATUS_OKAY() to iterate through
instances without the assumption that index 0 corresponds to SPI0
(which would be incorrect in the case when only SPI1 is enabled),
we need to check the base address to identify which SPI is being dealt
with.
Fixes#25673
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Current dma struture code didn't allowed only rx channel removal,
disabling tx channel (in spi client node) was leading compilation
issue.
Fix this by moving conditional code inside SPI_DMA_CHANNEL macro and
get the part of code which is present or removed (SPI_DMA_CHANNEL_INIT)
outside of {}.
Additionally, fix indentation on '\' in whole instance init macros
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
With this change, the spi transceive with dma function
waits for the spi busy flag reset and for the dma transfer end.
Then it reloads the channels until all buffers are consumed.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This change avoids the reload of the dma channel
in the callback function, just sets the corresponding Tx, Rx flag.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Remove semicolon between instance invocations of DT_FOREACH_IMPL_ and
thus DT_INST_FOREACH. This provides more flexibility to the user. This
requires we fixup in tree users to add semicolon where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Attached Flexcomm SPI driver to the main clock used by the core.
This means setting the SPI clock the same value as the core clock.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Convert to using DT_INST_LABEL() in the dma driver and convert dma users
to use the DMA property macros to get the dma controller name. We make
the assumption in the drivers that there is a single DMA controller
instance.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Clean up as we wish to move away from using these Kconfig settings.
Also removing them from the boards' default config.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Make drivers multi-instance wherever possible using DT_INST_FOREACH.
This allows removing DT_HAS_DRV_INST in favor of making drivers just
do the right thing regardless of how many instances there are.
There are a few exceptions:
- SoC drivers which use CMake input files (like i2c_dw.c) or otherwise
would require more time to convert than I have at the moment. For the
sake of expediency, just inline the DT_HAS_DRV_INST expansion for
now in these cases.
- SoC drivers which are explicitly single-instance (like the nRF SAADC
driver). Again for the sake of expediency, drop a BUILD_ASSERT in
those cases to make sure the assumption that all supported SoCs have
at most one available instance is valid, failing fast otherwise.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Rename DT_HAS_NODE to DT_HAS_NODE_STATUS_OKAY so the semantics are
clear. As going forward DT_HAS_NODE will report if a NODE exists
regardless of its status.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The optimisation in `spi_sam0_fast_txrx()` is broken, loading
two bytes into the `DATA` register in rapid succession will lose
one byte.
This can be observed by running `tests/drivers/spi/spi_loopback`.
The test will get stuck in `spi_sam0_fast_txrx()` forever waiting
for the final byte.
Undo this small optimisation and only load the next byte into the
`DATA` register after the response has been received.
This fixes `tests/drivers/spi/spi_loopback`.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
The DMA callback function now controls the tx or rx buffers
and reload dma in case of multiple trnasfer before the transfer ends
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Enable dma operations with or w/o a dmamux on STM32
for SPI periph/memory operations.
Use the pi dma client with dma macros
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Convert driver to use instance macro's instead of dts_fixup.h based
macros. This moves us closer to removing both dts_fixup.h and per
instance Kconfig symbols.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Rework the devicetree to utilize new DT_INST macros and extract per
instance data for clocks and dma from devicetree. We update the
atmel,sam0-spi binding for dma to replace the rxdma and txdma
properties with proper 'dmas' property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Reworked spi_sam driver to utilize new DT_INST macros as part of
this rework we also now get pin ctrl/mux configuration information
from the device tree instead of via Kconfig and defines in soc_pinmap.h
We remove defines from dts_fixup.h and soc_pinmap.h and associated
Kconfig symbols that are no longer needed due to getting all that
information from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace DT_CPU_CLOCK_FREQUENCY with a PATH based reference to cpu@0
(DT_PATH(cpus, cpu_0)) and than getting the clock_frequency property:
DT_CPU_CLOCK_FREQUENCY -> DT_PROP(DT_PATH(cpus, cpu_0), clock_frequency)
This lets us remove DT_CPU_CLOCK_FREQUENCY from dts_fixup.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use DT_INST_FOREACH macro to combine code used for multiple instances.
Remove unnecessary Kconfig options for UART instances.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
The check of the SF_TXDATA_FULL flag is only done on the register
address and not on the actual register content.
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
The SPIM driver has been converted already. Convert the SPI and SPIS
drivers too. Leave existing Kconfigs in place.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Sets the "dummy data" value to send when the transmit buffer is null.
Fixes the spi_null_tx_buf test in tests/drivers/spi/spi_loopback on the
lpcxpresso54114 board.
Tested on frdm_k64f, mimxrt1050_evk, and lpcxpresso54114_m4 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Make I2C and SPI drivers for nRF SoCs no longer dependent on Kconfig
options that enable instances (i.e. I2C_x and SPI_x). Now these drivers
enable hardware instances when corresponding nodes in devicetree are
enabled (have status "okay").
For I2C, SPI, and UART drivers, instead of using Kconfig dependencies
to prevent enabling of hardware instances that cannot be used together
(e.g. SPIM1 and TWIM1), a file that signals invalid configurations with
build assertions is added to compilation.
Also dependencies on HAS_HW_NRF_* options are removed from Kconfigs
of I2C, SPI, and UART drivers, as for hidden options that activate
proper type of driver such dependencies are not actually helpful.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `SPI_x_NRF_SPI*` that select the
type of nrfx driver (for SPI, SPIM, or SPIS peripheral) to be used
for a given instance. This prevents the options from being modified
in configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding SPI node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between SPI, SPIM, and SPIS for a given instance.
Since all `SPI_x_NRF_SPI*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert drivers that have the following pattern:
#if DT_INST_NODE_HAS_PROP(0, label)
INIT_MACRO(0)
#endif
...
#if DT_INST_NODE_HAS_PROP(n, label)
INIT_MACRO(n)
#endif
to use DT_INST_FOREACH(INIT_MACRO) instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use of macros such as SYS_POWER_STATE_SLEEP_2 needs to be guarded by
making sure CONFIG_SYS_POWER_SLEEP_STATES is defined.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Convert older DT_INST_ macro use in litex drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in sifive drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in STM32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in silab drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in cc13xx_cc26xx drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This allows us to start using DT_NODELABEL() to access SPIMs that way,
instead of via an alias.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This reverts commit 8739517107.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Towards cleaning up (and hopefully removing dts_fixup.h in the near
future). We need to move the handling of different names for the irq
flag propety into the driver and out of dts_fixup.h.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
On stm32 spi devices, there are 2 main IP variants, with and w/o
fifo. Fifo is not really used today, but still there is some
additional code handling fifo. Today this code is protected under
Kconfig symbol SPI_STM32_HAS_FIFO.
This code carries redundant information vs dedicated compatible
"st,stm32-spi-fifo", which is provided as unique driver compatible
for devices supporting this IP as opposed to use of "st,stm32-spi"
when fifo is not supported.
Having these 2 compatibles defined exclusively is not convenient for
migration to DT_INST as DT_INST macros contain compatible string and
hence it cannot be used to provide common compatible code for devices
defining different compatibles.
Based on these observations, review stm32 spi devices compatible
declarations. Devices supporting fifo will now declare both
compatibles, as proposed by dt spec: "[compatible] property value
consists of a concatenated list of null terminated strings,
from most specific to most general". Hence field will now be:
"st,stm32-spi-fifo", "st,stm32-spi"
This way, fifo enabled stm32 spi devices will generate both:
DT_INST_STM32_SPI_FOO and DT_INST_STM32_SPI_FIFO_FOO
As well as:
DT_COMPAT_ST_STM32_SPI and DT_COMPAT_ST_STM32_SPI_FIFO
So, DT_INST_STM32_SPI_FOO could be used for device initialization.
Also DT_COMPAT_ST_STM32_SPI_FIFO could be used for FIFO handling
code inside driver. Hence use it to replace Kconfig symbol
SPI_STM32_HAS_FIFO.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Attempt to deinitialize an nrfx driver that is not initialized results
in an assertion failure reported by the driver. And such attempt could
happen in SPI shims when the power state was switched between states
other than ACTIVE.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update hal_nordic's revision, so that NRFX_ASSERT uses __ASSERT_NO_MSG
directly, not through the assert macro that comes from from libc,
as the definition of the latter might be different when some specific
libc version is used, and this could generate troubles.
Replace also uses of assert() with __ASSERT_NO_MSG() in nrfx driver
shims that use this macro without including the corresponding header
file (i.e. that implicitly rely on assert.h being included from
nrfx_glue.h, which is no longer the case).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Same deal as in commit eddd98f811 ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for the remaining cases outside defconfig
files. See that commit for an explanation.
Will do the defconfigs separately in case there are any complaints
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Error codes from DSPI_MasterTransferNonBlocking are now handled in
tranceive to ensure that the context is unlocked when an busy bus
is detected.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
The current sam spi driver uses soc dependent name which duplicate
configuration to enable other platforms. This refactor current
definitions to a generic way to reuse symbols by multi soc definitions.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
spi_context_lock() & spi_context_release() are called in transceive()
function for a better readability.
Signed-off-by: Ismael Fillonneau <ismael.fillonneau@stimio.fr>
Update the hal_nordic module revision, to switch to nrfx 2.1.0.
Because the list of peripherals for nRF5340 has changed as follows:
- SPIM2 has been renamed to SPIM4
- SPIM2-3, SPIS2-3, TWIM2-3, TWIS2-3, and UARTE2-3 have been added
a couple of related corrections needed to be applied in dts and Kconfig
files, plus the spi_nrfx_spim driver has been extended with the support
for SPIM4.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Same deal as in commit 677f1e6 ("config: Turn pointless/confusing
'menuconfig's into 'config's"), for a newly-introduced stuff.
Also clean up headers to be consistent with recent cleanups.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Create new instances of SPI using single STM32_SPI_INIT() macro
invocation, similar as it is done for STM32 UART driver. Add also
implicit '#ifdef CONFIG_SPI_id' check, so it further reduces required
lines of code for each SPI instance definition.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Refactors the mcux dspi driver to use generated device tree macros
directly. Removes now unused dts fixup macros from kinetis socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Need to set device busy when enter into transceive function
in SPI DW driver.
In current SPI DW driver the transceive function don't set busy state,
but that is important for PM busy state.
This will lead to unexpected behaviors when system calls this
function and enter into idle state.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit adds SPI driver and its bindings using the USART peripheral
for Silicon Labs EFM32 and EFR32 MCUs.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Same deal as in commit 677f1e6 ("config: Turn pointless/confusing
'menuconfig's into 'config's"), for a newly-introduced SPI_MCUX_FLEXCOMM
symbol.
Also clean up the header to be consistent with recent cleanups.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The SPI SERCOM peripheral found on the SAMD5x/SAME5x is very much alike
the one found in previous SAM0 MCUs.
Only the clock setup is different.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
If possible, allow sending 16bits at once instead of 8bits. I found
large delays (up to 3us) between sending bytes due to Zephyr SPI
overhead, so allowing 16bits at a time if possible helps save that
time.
Signed-off-by: Pushpal Sidhu <psidhu.devel@gmail.com>
Cleanup around COND_CODE_1 usage and replacing with
IF_ENABLED if applicable.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Adds a shim layer around the mcux lpc flexcomm driver to adapt it to the
zephyr spi interface. It leverages heavily from the existing mcux dspi
shim driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Also replace some
config
prompt "foo"
bool/int
with the more common shorthand
config
bool/int "foo"
See the 'Style recommendations and shorthands' section in
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
After switching to nrfx 2.0.0, the Kconfig choice options that allowed
enabling of pull-up or pull-down for MISO lines in SPIs and SPIMs are
not properly supported, they are simply ignored. This commit restores
the possibility of applying pull configuration for MISO lines.
In earlier nrfx versions, the MISO pull configuration could be only
set globally, in nrfx_config files, for all SPI and SPIM instances
together. Since nrfx 2.0.0, this configuration can be applied per
instance. This commit takes advantage of this possibility and instead
of using a common Kconfig option as a global setting for all instances,
allows applying individual instance settings via devicetree.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
