Move the BOARD.dts files for Nordic-based boards to use the new I2C
devicetree properties for specifying the SDA and SCL pins.
This was done with a script.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
In the flash partition definitions for ARM boards,
the link to the legacy partition macros does not
exist any more. The commit cleans up the partition
definition by removing this link.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The SoC node has compatibles for the specific SoC in place, having the
same compatible at the top level is technically a conflict and the
top-level one should really just be about the board. Remove the SoC
related compatibles at the top-level.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the new pin and interrupt configuration API. Update all
devicetree bindings to add INT signal active level. Document active
level.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the GPIO_ACTIVE_LOW to signal that the button pins are active low,
instead of the deprecated GPIO_INT_ACTIVE_LOW.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Converts the fxos8700 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on frdm_k64f and rv32m1_vega_ri5cy boards. The latter verifies
that the reset output works correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The original v1.3 had MMA8653+MAG3110, but v1.5 has verified LSM303AGR
and theoretical FXOS8700. Add the v1.5 variant 1 nodes in disabled
form; they can be enabled through overlays.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use Device Tree,and in particular a new 'bt-c2h-uart' to select which
UART is being used to communicate with an external BLE Host when acting
as a Controller.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add the bt-mon-uart chosen node to all the nRF-based boards so that they
can all use CONFIG_BT_DEBUG_MONITOR without additional changes.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
As we want to remove dts dependency on Kconfig, we had a case based on
CONFIG_BOOTLOADER_MCUBOOT. From a DTS point of view that was just
getting the chosen property 'zephyr,code-partition' set. We can easily
move this to the actual dts files and remove the mcuboot.overlay.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Remove the ifdef related to CONFIG_FS_FLASH_STORAGE_PARTITION. There
shouldn't be any harm in always having the partition around as we'll
just generate the defines related to and most applications will ignore
them.
Helps get one step closer to have DTS not depend on Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the GPIO info for the buttons into the dts, this lets us match what
all other boards are doing. Update some sample & test code to use the
dts generated SW0_GPIO_CONTROLLER define instead of SW0_GPIO_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_NRF51822_QFAA
CONFIG_SOC_NRF51822_QFAB
CONFIG_SOC_NRF51822_QFAC
CONFIG_SOC_NRF52810_QFAA
CONFIG_SOC_NRF52832_QFAA
CONFIG_SOC_NRF52832_CIAA
CONFIG_SOC_NRF52832_QFAB
CONFIG_SOC_NRF52840_QIAA
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
UART pins (TX, RX, RTS, CTS) are now configured in DTS files.
RTS and CTS definitions are optional. If flow control is enabled
and RTS/CTS pins are not defined, then compiler will issue
an error message.
Signed-off-by: Paweł Zadrożniak <pawel.zadrozniak@nordicsemi.no>
This commit selects HAS_DTS_I2C in bbc_microbit board definition.
It fixes issues similar to issue #8511 for bbc_microbit board
Signed-off-by: Mandar Chandrakant Thorat <mandar.chandrakant.thorat@intel.com>
SDA and SCL pins can now be configured through DTS.
Pins on development kits have been assigned according to arduino
headers.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
FS_FLASH_MAP_STORAGE keyword enables the storage partition,
but it was depend on flash_map module which is unused by
NFFS. This patch makes it independent thanks
to it is possible to enable the storage partition
without flash_map module.
FS_FLASH_MAP_STORAGE was renamed to
CONFIG_FS_FLASH_STORAGE_PARTITION
as it is independent for flash_map.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
These are a direct copy from the nrf51_pca10028 board, since it's also
an nRF51 and has the same size flash.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The i2c controller nodes are enabled in the board specific dts files
on boards where the controller was enabled in the board Kconfig.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Move the dts files into the board dir so that board ports can be more
standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
