The spi node of the led_ws2812 now includes the frame format
as defined by the dts bindings spi-device.yaml
SPI_FRAME_FORMAT_TI is selected with overlay for target boards.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
The STM32 single_wire example was merged in parallel to this sample
and ended up as a sub-folder of this one. Separate both into their
own folders.
Signed-off-by: Martin Jäger <martin@libre.solar>
Add optional user data argument to can_set_state_change_callback() to
comply with Zephyr API design guidelines.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This sample demonstrates the use of the UART driver. The data is
received using an ISR callback and a message queue. For sending data,
the polling API is used.
Signed-off-by: Martin Jäger <martin@libre.solar>
Rename a few CAN API functions for clarity and consistency with other
Zephyr RTOS APIs.
CAN_DEFINE_MSGQ() becomes CAN_MSGQ_DEFINE() to match K_MSGQ_DEFINE().
can_attach_isr() becomes can_add_rx_filter() since a filter callback
function is not an interrupt service routine (although it is called in
isr context). The word "attach" is replaced with "add" since filters are
added, not attached. This matches the terminology used is other Zephyr
APIs better.
can_detach() becomes can_remove_rx_filter() to pair with
can_add_rx_filter().
can_attach_msgq() becomes can_add_rx_filter_msgq() and documentation is
updated to mention its relationship with can_add_rx_filter().
can_register_state_change_isr() becomes can_set_state_change_callback()
since a state change callback function is not an interrupt service
routine (although it is called in isr context). The word "register" is
replaced with "set" since only one state change callback can be in
place.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Excluded due to conflicts with adafruit_2_8_tft_touch_v2.
Both boards got a touch controller.
Signed-off-by: Konstantinos Papadopoulos <kostas.papadopulos@gmail.com>
Change the can_tx_callback_t function signature to use an "int" (not an
uint32_t) for representing transmission errors.
The "error" callback function parameter is functionally equivalent to
the return value from can_send() and thus needs to use the same data
type and needs to be able to hold negative errno values.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Specify in the API that the callback must be registered before the
channel is enabled, fix the NRFX IPC driver to be compliant and change
the MBOX sample.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Convert the CAN sample from using can_attach_workq() to using
can_attach_msgq() and triggered work via k_work_poll_submit().
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Place the nodes to the proper place into the DT. The driver is calling
directly into the NRFX without using any direct memory addressing so
this is mostly a cosmetic fix.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Various obsolote and misnamed platfomrs in test filters theat went
undetected for a while.
Fixes#41222
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Added dts overlay and config to support using
samples/driver/apa201 with blueclover_plt_demo_v2_nrf52832.
Signed-off-by: Jeremy Wood <jeremy@bcdevices.com>
Search and replace `message(INFO " ` with `message(STATUS "`.
This would otherwise print "INFO <message"
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Sample should only be run if led is present on board.
Since, this is not the case on any of the in tree boards,
set the sample as build-only.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rework samples to use DEVICE_DT_GET and DT_CHOSEN
to get default display controller device.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Deprecate the use of CAN-specific error return values and replace them
with standard errno values.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
This adds an spi master mode driver via bitbanged gpio. Only syncronous
transfers are implemented. Clock signal timing is accomplished via busy
waits, the gpios are manipulated via the standard gpio interface; these
two factors limit the frequency at which it can operate - but here
a simple and generic implementation was chosen over performance.
The driver supports the various clock polarity and phase
configurations, and can also work with word sizes which are non
multiples of 8bits, currently up to 16 bits.
A sample program is also added demonstrating basic use of the driver
with 9bit data words.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Pinctrl is missing in i2c1 device description on stm32373c_eval
ovderlay file, besides using I2C1 this board (as mentioned in readme)
requires to remove 2 resistors on the board.
Make it simple and instead use a board with arduino_i2c port
available.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Since drivers implement a callback based on action and not the state,
we should be using the API based on the action instead of the one based
on the state.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Currently the IPM samples are hosted in the IPC sample location. Clean
this situation up by moving the IPM samples to a new location.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Rename the Zephyr chosen property for specifying the default CAN bus
controller from "zephyr,can-primary" to "zephyr,canbus".
The "zephyr,can-primary" property name was selected in antipation of
adding support for redundant CAN networks, which we have yet to
add. Meanwhile, the "primary" term causes confusion for non-redundant
CAN bus configurations (and the "can" term doesn't match the name of the
Zephyr CAN bus subsystem).
The CAN in Automation (CiA) 302-6, which deals with CANopen network
redundancy, uses the terms "default interface" and "redundant
interface". If/when we add support for redundant CAN networks, the
"zephyr,canbus" chosen property can be supplemented with a
"zephyr,canbus-redundant" chosen property.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
As the already existing macro K_MEM_SLAB_DEFINE results in
two variable definitions, the preceding static modifier leads to
a seemingly working solution, though linkage conflicts will occur
when the same memory slab name is used across multiple modules.
The new K_MEM_SLAB_DEFINE_STATIC macro duplicates the functionality of
K_MEM_SLAB_DEFINE with the difference that the static keywords are
internally prepended before both variable definitions.
The implementation has been tested on my Zephyr project (the build
issue faded out). The documentation has been updated altogether
with all incorrect occurences of static K_MEM_SLAB_DEFINE.
Signed-off-by: Pavel Hübner <pavel.hubner@hardwario.com>
Enable watchdog timer on RT1160 evk. This was tested using
the watchdog timer api test (tests/drivers/watchdog/wdt_basic_api)
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
ADC support verified with driver sample. LPADC1 channel 0 pin used,
which maps to pin 10 on J9 on the EVK.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
This commit adds the support to run the SPI NOR sample code on the
npcx7m6fb_evb and npcx9m6f_evb boards.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Change-Id: I780c5dfcf53f3ac537da946673fc03f5ee24e90c
Use a more precise Kconfig symbol name to avoid namespace conflicts when
more NRFX-dependent drivers will be added.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Convert remaining tests and samples to using find_package() instead of
literally including the CMake boilerplate code.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Enables ADC1 on the RT1020 evaluation board. Channels 10 and 11 of this
ADC are exposed as pins 1 and 2 of J18 on the evk.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Enables ADC on RT1015 evaluation board. Channels 1 and 13 are exposed as
pins 2 and 1 of J18 on the EVK.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Added ADC support to RT1010 evaluation board. ADC channels 1 and 2 are
exposed as pins 10 and 12 of J26.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Adds ADC support to RT1024 EVK. ADC channels 10 and 11 are enabled as
pins 2 and 4 on J18 of the evaluation board
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Enables the ADC on the RT1060 evaluation board. Channels 0 and 15 of
ADC1 are available on pins 1 and 0 of J23, respectively.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Make use of the new MBOX APIs to create a ping-pong sample application.
This sample is using the NRFX IPC peripheral to send and receive signals
on different channels
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Moves DAC driver configuration defaults from the application level to
the board level for the bl5340_dvk board.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Moves DAC dts node and driver configuration defaults from the
application level to the board level for the bl654_dvk board.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Moves DAC dts node and driver configuration defaults from the
application level to the board level for the bl653_dvk board.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Moves DAC dts node and driver configuration defaults from the
application level to the board level for the bl652_dvk board.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
