Most APIs have the default synchronous and an asynchronous version
with the sufix _async because that is the most common use.
All devices in tree right now are using the synchronous version, so
just change it to be consistent with the rest of the system.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Since we are using mutex to protect critical sections and mutexes are
reentrant, it is possible to get rid of atomic for the state because
we can lock the mutex in device_pm_callback.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Changing from spinlock to mutex makes the running thread be preempted
and the workqueue ran. This changed the prints order in this sample.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
File prj.mcp2515.conf was previously removed from project as it was
made redundant.
Paths containing uppercase CAN were changed to lowercase.
Signed-off-by: Nick Ward <nick.ward@setec.com.au>
When a WIFI driver is slow to get interface up the system not connect
to WIFI access point. This add some tries to let driver be proper
initialize to allow accept connection request.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Similar to commit c6ff61220e, use a
harness config to limit execution of the adafruit_2_8_tft_touch_v2
sample variant to boards that have this shield attached.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
USB audio class samples are generic and can be built for any
board that supports USB device and isochronous endpoints.
Add app.overlay that uses aliases and remove board specific overlays.
Note: USB audio is still experimental and even though the sample can
be built for specific platform, it does not mean that it can be run
on it without issues.
Fixes: #25313
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Converts the display driver and lvgl sample.yaml to select boards for
the adafruit_2_8_tft_touch_v2 shield configuration by depending on the
arduino_{gpio,i2c,spi} features instead of using an explicit
platform_allow list. This will enable twister to automatically select
new boards that add support for Arduino ports.
The reel_board and reel_board_v2 are excluded due to a conflict between
display drivers (onboard display vs. shield display).
The ubx_evkannab1_nrf52832 board is excluded due to a conflict between
the arduino_spi and arduino_i2c ports, which cannot be used
simultaneously.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes sample execution ending early with error, as it attempted
to mount the LittleFS partition second time, after it has already
been mounted by the auto-mount feature.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
"child resuming" text is printed when dummy_device_pm_ctrl is
called. The driver is using the async api, this means that this call
will happen only when the worqueue runs what will happen only when
this thread blocks waiting on the conditional variable.
The last thing is, the dummy driver was putting the parent driver
asynchronously consequently the "parent suspending" message would just
print after "Device PM sample app complete". Just use the sync API to
get these messages printed in the expected order.
Fixes#35336
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Remove this intrusive tracing feature in favor of the new object tracing
using the main tracing feature in zephyr. See #33603 for the new tracing
coverage for all objects.
This will allow for support in more tools and less reliance on GDB for
tracing objects.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add support for new tracing macros in test backend. Move header from
sample into the subsystem and make it available for general testing with
any application.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The sync API was using k_poll_signal and in certain conditions is
possible multiple threads waiting on a signal leading to an undefined
behavior.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The context parameter used across device power management is
actually the power state. Just use it and avoid a lot of
unnecessary casts.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add mimxrt685_evk_cm33 board to the platform_allow list
for the littlefs sample application.
Signed-off-by: Saurabh Jagdhane <saurabh.jagdhane@nxp.com>
The Kconfig option SHELL_BACKEND_SERIAL had been defaulting to y,
causing shell to block mcumgr from processing serial input.
Fixes: #34670
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
With the change to use GPIO_DT_SPEC_GET_OR a number of platforms
failed to build these samples. This was due to the GPIO drivers not
being enabled by default. Add CONFIG_GPIO=y to the prj.conf to fix
the issue.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Refactor and simplify the bluetooth buffer configurations to improve the
easy of configurations and eliminate invalid ones.
By moving configurations out of host and controller specific
configurations and into a common one it becomes easier to configure
the host and controller separately as the same configurations can be
used as would be for a combined build.
All HCI configurations are now given exluding the matching HCI header,
which eases the configuration as the application don't have to know the
different header sizes.
The BT_RX_BUF_LEN is split into ACL and Event, as well as the suprising
use of Command size.
BT_L2CAP_RX_MTU is removed as the stack does not support reassembling of
HCI ACL data to larger L2CAP PDUs. The application will have to set
ACL RX size and account for the L2CAP PDU header itself.
BT_EATT_RX_MTU was removed as it is only used for setting a different
default value for another option which leads to the stuck kconfig symbol
problem.
The configurations can be updated according to the table below:
** New configuration | ** Old configuration
All configurations
BT_BUF_ACL_RX_SIZE | BT_L2CAP_RX_MTU + 4
BT_BUF_ACL_RX_SIZE | BT_RX_BUF_LEN - 4
BT_BUF_EVT_RX_SIZE | BT_RX_BUF_LEN - 2
BT_BUF_CMD_TX_SIZE | BT_RX_BUF_LEN - 3
BT_BUF_CMD_TX_COUNT | BT_HCI_CMD_COUNT
BT_BUF_EVT_RX_COUNT | BT_RX_BUF_COUNT
BT_BUF_ACL_RX_COUNT | BT_RX_BUF_COUNT
BT_BUF_ACL_RX_COUNT | BT_ACL_RX_COUNT
BT_BUF_EVT_DISCARDABLE_SIZE | BT_DISCARDABLE_BUF_SIZE - 2
BT_BUF_EVT_DISCARDABLE_COUNT | BT_DISCARDABLE_BUF_COUNT
Controller-build
BT_BUF_ACL_TX_SIZE | BT_CTLR_TX_BUFFERS_SIZE
BT_BUF_ACL_TX_COUNT | BT_CTLR_TX_BUFFER
HCI-bridge
BT_BUF_ACL_TX_SIZE | BT_HCI_ACL_DATA_SIZE
BT_BUF_ACL_TX_COUNT | 6
Fixed invalid configurations setting either BT_L2CAP_RX_MTU or
BT_CTLR_DATA_LENGTH_MAX larger than BT_RX_BUF_LEN could lead to buffer
overruns.
Fix advertising report max data length calculation.
This always used the BT_DISCARDABLE_BUF_SIZE macro but this feature
can be turned off and advertising reports will be allocated from the RX
buffer in that case. Also controller-build does not have this buffer
(in hci_raw.c). Also the wrong HCI header was used in the calculation,
HCI event header should have been used instead of HCI ACL header.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Use `pm_device_*` prefix for the device runtime PM API. This adds the
API to the `pm` namespace, making it clear part of the PM subsystem.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Get the correct flash device from the storage partition node.
The current code is relying on the invalid assumption that the
chosen zephyr,flash-controller node is the device which contains
the storage partition.
Reported-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Replace device_get_binding with DEVICE_DT_GET(). Fix and clean up
error handling and debug printing during initialization.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Use the new GPIO_DT_SPEC_GET_OR() macro to clean up the node detection
code by eliminating conditional compilation. This increases code
coverage on platforms where not all the devicetree nodes are
available.
Clean up some whitespace while we're at it.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Adds mimxrt1060_evk and mimxrt1064_evk boards to the platform_allow list
for the smp_svr sample application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
In this example, python test case get the running directory by handling
the "--cmdopt" option passed by pytest.
Signed-off-by: YouhuaX Zhu <youhuax.zhu@intel.com>
The cbprintf packaging needs CONFIG_CBPRINTF_PACKAGE_LONGDOUBLE
to be enabled to work with long double. So #ifdef that inside
CONFIG_FPU.
Also add to the sample.yaml to enable testing with FPU and
long doubles.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Allow SMP processing for SOF on ADSP. Note, that after this
SOF will build with SMP support enabled on all cAVS versions,
but secondary cores will remain disabled unless an SMP
topology is loaded by the host.
Signed-off-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Reboot functionality has nothing to do with PM, so move it out to the
subsys/os folder.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This adds a sample application on dictionary-based logging.
The README file includes instruction on how to run the log parser
to generate human readable log messages.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
