Add minimum harness and to get the sample passed when run using
twister.
Adding console validates uart init with DEVICE_RUTIME=y.
Additionally, clarify comment about DEBUG activation.
Fixes#35033
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This sample turn on/off the LED every two seconds and then sleeps. When
the LED is on we don't want the system putting it down when goes to
sleep. So, just setting this device as busy.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Restrict sample execution in CI to boards that have
"st,stm32-lptim" enabled so we're sure it is a STM32 target.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Refactor and simplify the bluetooth buffer configurations to improve the
easy of configurations and eliminate invalid ones.
By moving configurations out of host and controller specific
configurations and into a common one it becomes easier to configure
the host and controller separately as the same configurations can be
used as would be for a combined build.
All HCI configurations are now given exluding the matching HCI header,
which eases the configuration as the application don't have to know the
different header sizes.
The BT_RX_BUF_LEN is split into ACL and Event, as well as the suprising
use of Command size.
BT_L2CAP_RX_MTU is removed as the stack does not support reassembling of
HCI ACL data to larger L2CAP PDUs. The application will have to set
ACL RX size and account for the L2CAP PDU header itself.
BT_EATT_RX_MTU was removed as it is only used for setting a different
default value for another option which leads to the stuck kconfig symbol
problem.
The configurations can be updated according to the table below:
** New configuration | ** Old configuration
All configurations
BT_BUF_ACL_RX_SIZE | BT_L2CAP_RX_MTU + 4
BT_BUF_ACL_RX_SIZE | BT_RX_BUF_LEN - 4
BT_BUF_EVT_RX_SIZE | BT_RX_BUF_LEN - 2
BT_BUF_CMD_TX_SIZE | BT_RX_BUF_LEN - 3
BT_BUF_CMD_TX_COUNT | BT_HCI_CMD_COUNT
BT_BUF_EVT_RX_COUNT | BT_RX_BUF_COUNT
BT_BUF_ACL_RX_COUNT | BT_RX_BUF_COUNT
BT_BUF_ACL_RX_COUNT | BT_ACL_RX_COUNT
BT_BUF_EVT_DISCARDABLE_SIZE | BT_DISCARDABLE_BUF_SIZE - 2
BT_BUF_EVT_DISCARDABLE_COUNT | BT_DISCARDABLE_BUF_COUNT
Controller-build
BT_BUF_ACL_TX_SIZE | BT_CTLR_TX_BUFFERS_SIZE
BT_BUF_ACL_TX_COUNT | BT_CTLR_TX_BUFFER
HCI-bridge
BT_BUF_ACL_TX_SIZE | BT_HCI_ACL_DATA_SIZE
BT_BUF_ACL_TX_COUNT | 6
Fixed invalid configurations setting either BT_L2CAP_RX_MTU or
BT_CTLR_DATA_LENGTH_MAX larger than BT_RX_BUF_LEN could lead to buffer
overruns.
Fix advertising report max data length calculation.
This always used the BT_DISCARDABLE_BUF_SIZE macro but this feature
can be turned off and advertising reports will be allocated from the RX
buffer in that case. Also controller-build does not have this buffer
(in hci_raw.c). Also the wrong HCI header was used in the calculation,
HCI event header should have been used instead of HCI ACL header.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
There is a choice to log btmon logs over UART or RTT.
You can choose number of RTT buffer, set its name and size.
Replaced CONFIG_BT_DEBUG_MONITOR with CONFIG_BT_DEBUG_MONITOR_UART
for UART usage and CONFIG_BT_DEBUG_MONITOR_RTT for RTT.
Signed-off-by: Magdalena Kasenberg <magdalena.kasenberg@codecoup.pl>
pm_power_state_force no longer requires the idle thread to run.
Just removing the following k_sleep for two reasons, first it is
not necessary, second it tests that pm_power_state_force works
as it should.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
pm_power_state_force no longer requires the idle thread to run. Just
removing the following k_sleep for two reasons, first it is not
necessary, second it tests that pm_power_state_force works as it
should.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Replace all existing deprecated API with the recommended alternative.
Be aware that this does not address architectural errors in the use
of the work API.
Fixes#34097
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
This sample has implemented USB HID class callbacks that
actually have no function and should not return 0.
Remove unused and wrong implemented callbacks.
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
The sample showed the error between the two clocks, but did not show
how to use the skew to reconstruct one clock from the other and the
resulting error.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Change to use the BT_ATT_FIRST_ATTTRIBUTE_HANDLE and
BT_ATT_LAST_ATTTRIBUTE_HANDLE instead of the literal values where
applicable.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Take the int-pin information (i.e. what pin between INT1
and INT2 the drdy is attached to) directly from DT.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Don't allow user to choose CPU_ARCEM / CPU_ARCHS options
but select them when exact CPU type (i.e. EM4 / EM6 / HS3X/ etc)
is chosen.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Use the reschedule solution as there may be cases where a newer
deadline should supersede an older one.
The implementation has no locking and so has data races between the
handler and external events. Emit a console diagnostic in one case
where the race can be detected.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
All dma drivers are devicetree based now so we can remove the last
bits of Kconfig associated with the old driver style.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace device_get_binding with DEVICE_DT_GET for getting access
to the io-channels/adc controller device.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add an object to retain data across both reboots and entry to
SYSTEM_OFF. This only works on nRF52, since nRF51 and nRF53 require
different low-level operations to configure RAM retention.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Enable PECI and KSCAN drivers to evaluate any side-effect
in LPM entry/exit and power consumption.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
This commit adds the nRF IEEE 802.15.4 Service Layer Fault Handler
to the 802154_rpmsg sample.
Signed-off-by: Czeslaw Makarski <Czeslaw.Makarski@nordicsemi.no>
Simplify pm subsystem removing PM_STATE_LOCK option. Constraints API is
small and is a key component of power subsystem.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The sample was failing twister test with a timeout because there was
no pass/fail criteria for it (nothing was tested). The fix adds
harness on consolse and some output that can be verified.
Signed-off-by: Maciej Perkowski <Maciej.Perkowski@nordicsemi.no>
In the last step of the example, the system should go into soft off
state in order to match the original intent in the example to go
into the hardware's SHUTDOWN mode.
Fixes#31727
Signed-off-by: Vincent Wan <vanti.coder@gmail.com>
Change subsystem to use struct pm_state with substate-id instead of
using only the power state category.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Migrate the whole pm subsystem to use new power states information
from power_state.h and get states and residency properties from
device tree.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Provide a demonstration of using the timeutil skew infrastructure to
measure the relative error of the two clock sources on Nordic boards.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Conditionally use either DPPI or PPI channel in the sample so that
it can be built for all nRF SoCs. Update documentation accordingly.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Get rid of weak functions adding a new API to register an object to
receive notifications when the system changes power state.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
some tests configured with CONFIG_NEWLIB_LIBC=y,
it's better to add a filter filter: TOOLCHAIN_HAS_NEWLIB == 1
in those tests yaml file.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
- Remove SYS_ prefix
- shorten POWER_MANAGEMENT to just PM
- DEVICE_POWER_MANAGEMENT -> PM_DEVICE
and use PM_ as the prefix for all PM related Kconfigs
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The sample referenced the ADC through an alias that either never
existed or (more likely) has since been removed. Use the node label
instead.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
