Change the drivers's compatible from atmel,sam-tc to atmel,sam-tc-qdec.
The atmel,sam-tc should be reserved for the future counter driver.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
STM32 internal temperature sensor driver.
This sensor can be used to measure the temperature of the CPU
and its surroundings.
Signed-off-by: Eug Krashtan <eug.krashtan@gmail.com>
The MAX17262 is an ultra-low power fuel-gauge IC which implements the
Maxim ModelGauge m5 algorithm. The IC monitors a single-cell battery
pack and supports internal current sensing for up to 3.1A pulse
current. The IC provides best performance for batteries with 100mAhr
to 6Ahr capacity.
Signed-off-by: Matija Tudan <mtudan@mobilisis.hr>
Take the int-pin information (i.e. what pin between INT1
and INT2 the drdy is attached to) directly from DT.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Create a common properties file that will be included by all bindings
(as i2c and spi) handled by lsm6dso driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Currently the MAX17055 driver assumes that a battery matching the
default characteristics is used.
This change allows battery characteristics to be specified in device
tree and writes them to the MAX17055 on initialization.
Existing default values are maintained for backwards compatibility.
Initialization routine taken from MAX17055 Software Implementation
Guide, document UG6365.
Signed-off-by: Hayden Ball <hayden@playerdata.co.uk>
Support single mode operation by enabling it and
making the driver to use the interrupt to findout
when the data is ready for fetch. The sample fetch
will be blocked for a specified maximum time untill
the interrupt happens.
* Make operation mode configurable in DTS file
* Make offset cancellation configurable in DTS file
* Use single common .yaml file for both i2c and spi
* Store above configurations in dev->config_info
Signed-off-by: Masoud Shiroei <masoud.shiroei@assaabloy.com>
Adds support for the Texas Instruments FDC2X1X Capacitance-to-Digital
Converter for Proximity and Level Sensing Applications.
Signed-off-by: Igor Knippenberg <igor.knippenberg@gmail.com>
Convert ism330dhcx INT_PIN attribute from Kconfigs to Device
Tree binding properties. Here int-pin has been defined as
enum with two possible values: 1 and 2.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Convert ism330dhcx accel and gyro odr attributes from Kconfigs to Device
Tree binding properties.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Converts ism330dhcx accel and gyro range attributes from Kconfigs to
Device Tree binding properties.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Create a common properties file that will be included by all bindings
(as i2c and spi) handled by ism330dhcx driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
During the driver init, the function will set the sensor resolution
based on the driver's dts variable "resolution"
The driver's device tree has been updated to include the value
"resolution".
The default is set to the highest resolution of 0.0625C.
Moved mcp9808_reg_write from mcp9808_trigger.c to mcp9808.c
This allows resue of the same function in both the trigger and
resolution functions.
Function name changed to xxx_16bit to distinquish it from the 8
bit write function that will added.
Signed-off-by: Steven Daglish <s.c.daglish@gmail.com>
Create a common binding file that will be included by all bindings
handled by iis2iclx driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Initial driver and sample application of
TDK Invensense ICM42605 6-axis motion sensor.
This driver provide DTS for nRF52 DK board DTS setting.
Providing features are below.
Sensor data streaming - Accel, gyro
Tap, Double tap triggering.
Set/Get FSR, ODR by set attr API
Support multi instance feature.
Signed-off-by: JuHyun Kim <jkim@invensense.com>
Move iis2dlpc trigger pulse configurations from Kconfigs to Device Tree.
Moreover the dts properties have been renamed as 'tap', which sounds a
better name to immediately catch the feature behind it. Since tap
threshold cannot be zero, this value (which is the default in dts
binding) is used to enable/disable the device feature per each axis.
The event can be generated on INT1 only.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The IIS2DLPC drdy interrupt can be routed to either INT1 or
INT2 pin. Currently the selection is done by Kconfig configuration.
This commit is instead moving it into Device Tree as 'drdy-int'.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add some details to help new users learn how to manage the nodes
for compatibles corresponding to IP blocks on Nordic SoCs.
The focus is on IP blocks where the pinmux is configured in
devicetree. These typically have individual properties for each pin,
like a SCK pin on a SPI peripheral, which correspond directly to a
PSEL register value. These violate the usual devicetree convention of
using a 'foo-gpios <&gpioX ...>' phandle property and work in ways
that only make sense if you understand the underlying register map, so
it's worth explaining them a bit more carefully.
Skip these two bindings, which have no drivers: nordic,nrf-i2s.yaml,
nordic,nrf-pdm.yaml.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Create a common binding file that will be included by all bindings
handled by iis2dlpc driver. For now this includes optional drdy-gpios
property and it is shared by the i2c and spi version of the driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Converts fxos8700 magnetic vector magnitude options from Kconfigs to
optional device tree properties.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converts fxos8700 power mode options (normal, low noise low power, high
resolution, low power) from Kconfigs to an optional device tree
property.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converts fxos8700 range options (2g, 4g, 8g mode) from Kconfigs to an
optional device tree property.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
LIS3DH and LIS2DH12 devices share the same driver with
LIS2DH device. So, the bindings are reusing the same
common structure (as LSM30AGR-ACCEL and LSM303DLHC-ACCEL
devices are already doing)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Make this driver multi-instance and use the new API.
Notes for sensorhub mode:
In case of multiples devices it is possible that some of them
has i2c slaves attached to it (sensorhub mode) but not the
others. Since the driver is configured in the same way for
all the instances (CONFIG_SENSORHUB=y), the routine that initialize
the sensorhub part does not fail anymore in case no slaves
are found for a particular instance. Instead, those non-sensorhub
driver instances will set the shub_inited flag to false and
will totally ignore the feature.
Notes for triggers:
In case of multiples devices the device pin the interrupt wire is
attached to can be different (INT1 or INT2 pin). So, this
information has been moved in DTS and then stored in the
specific instance config structure.
Currently the driver is able to handle a sngle interrupt line
at a time attached to either INT1 or INT2.
MOreover, the interrupt initialization for a driver instance proceed
only if the drdy has been configured in its DT, else it returns ok.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The IIS2ICLX is a high-accuracy. ultra-low noise, low-power
two-axis linear accelerometer which can be interfaced through
either I2C or SPI bus.
Its high accuracy, stability over temperature and repeatability
make IIS2ICLX particularly suitable for inclination measurement
for industrial applications (inclinometers).
https://www.st.com/resource/en/datasheet/iis2iclx.pdf
This driver is based on stmemsc i/f v1.03.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
* Add comments about the default settings
* Change proximity-trigger default to match POR of 'disabled'
* Added reference to datasheet
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Generalize io-channels and io-channel-names devicetree node properties
and move their definitions to base.yaml. Keep binding specific
description where relevant.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for wsen-itds 3-axis accel sensor, provides acceleration,
temperature data reading and supports configuring of output data rate,
operating mode and scale.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
The parameters for this fuel gauge depend on the hardware design and
the expected battery. These should not be defaulted to a value that
may be inappropriate. Require that they be explicitly provided.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add support to STM IIS2DH the ultra-low-power highperformance
three-axis linear accelerometer.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The IIS2MDC is a 3D digital magnetometer ultra-low power sensor
for industrial applications, which can be interfaced through
either I2C or SPI bus.
https://www.st.com/resource/en/datasheet/iis2mdc.pdf
This driver is based on stmemsc i/f v1.02.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
