After i2c_reset, there is still no external pull-up I2C bus,
and finishing off the rest of loop causes the code to hang
indefinitely.
This patch fixes that if I2C bus is not available(No external
pull-up), dropping the transaction.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
The context parameter used across device power management is
actually the power state. Just use it and avoid a lot of
unnecessary casts.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Previously to this commit, nothing was done to restore the bus to an
healthy level.
However, I2C devices sometimes needs help to recover from an aborted
transaction.
Therefore, we now add a call to nrfx_{twi, twim}_bus_recover().
Signed-off-by: Xavier Chapron <xavier.chapron@stimio.fr>
nrfx 2.5.0 release includes the patch in the nrfx_twim driver that
fixes the driver behavior for zero-length transfers. No need to keep
the same fix in the shim layer.
This effectively reverts cb86a2b306.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
For a zero-length transfer, the STOP task is not triggered
automatically by the shortcut with the event that signals
the transfer end because such event is not generated.
Trigger this task "manually" to prevent the driver getting
stuck after the address byte is acknowledged.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Move emul.h out of the top level include/ dir into
include/drivers/emul.h and deprecated the old location.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
With some additional macro-magic we can remove the CMake-based header
file template feature, and instead take advantage of the usual
DT_INST_FOREACH_STATUS_OKAY() macro.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are no boards that need hard-coded interrupts so just remove this
build-time conditional branch. The way going forward is that all PCIe
devices should always use PCIE_IRQ_DETECT.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
These changes turn out to have been incompatible with the way pinctrl
drivers are going to work, so we need to go back to what we had before
until we can agree on a better approach.
Squash of the following reverts:
Revert "boards: nrf: fix deprecated I2C properties"
This reverts commit 2a4ac9ac02.
Revert "samples: switch nrf overlays to sda-gpios, scl-gpios"
This reverts commit 01bb08e7d8.
Revert "boards: nrf: switch to sda-gpios, scl-gpios"
This reverts commit 17a66304c4.
Revert "i2c: nordic: switch to phandle arrays for pinmux"
This reverts commit 821c03a14a.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
When, due to EMC, a spike happens on the SCL line the driver stay in
BUSY state. It could be reproduced by forcing the SCL temporarily to
ground. It's probably a behavior relating to the operation of
multi-master.
By adding a timeout to the msg_read and msg_write function we can
detect that something went wrong, and when that happens we force the
end of communication.
Signed-off-by: Julien D'Ascenzio <julien.dascenzio@paratronic.fr>
Ported commit 49a3ce5881
Transfer locking is required if multiple devices use the same i2c bus.
Signed-off-by: Pieter De Gendt <pieter.degendt@basalte.be>
RX/TX buffer depth are configurable parameters of DW_apb_i2c.
Change code from using fixed value I2C_DW_FIFO_DEPTH to using
register ic_comp_param_1 for RX/TX buffer depth.
Signed-off-by: Satoshi Ikawa <ikawa.satoshi@socionext.com>
Current DW I2C driver uses 32 bit access for some registers and
16 bit access for others. So if DW I2C IP is connected via bus
which doesn't support 16 bit access we will get bus error.
Fix that by switching to 32 bit access only instead of 16
and 32 bit mix.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
Currently there is no way to distinguish between a caller
explicitly asking for a semaphore with a limit that
happens to be `UINT_MAX` and a semaphore that just
has a limit "as large as possible".
Add `K_SEM_MAX_LIMIT`, currently defined to `UINT_MAX`, and akin
to `K_FOREVER` versus just passing some very large wait time.
In addition, the `k_sem_*` APIs were type-confused, where
the internal data structure was `uint32_t`, but the APIs took
and returned `unsigned int`. This changes the underlying data
structure to also use `unsigned int`, as changing the APIs
would be a (potentially) breaking change.
These changes are backwards-compatible, but it is strongly suggested
to take a quick scan for `k_sem_init` and `K_SEM_DEFINE` calls with
`UINT_MAX` (or `UINT32_MAX`) and replace them with `K_SEM_MAX_LIMIT`
where appropriate.
Signed-off-by: James Harris <james.harris@intel.com>
Deprecate the scl-pin and sda-pin properties in the devicetree.
Provide new scl-gpios and sda-gpios properties instead.
This lets the user specify SCL and SDA like this:
&i2c0 {
scl-gpios = <&gpio0 1 0>;
sda-gpios = <&gpio1 4 0>;
};
Instead of having to use:
&i2c0 {
scl-pin = <1>;
sda-pin = <36>;
};
Provide error checking and understandable error messages for invalid
configurations.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
We will need this to be able to DEVICE_DT_GET() bus devices from
tests/drivers/build_all in an upcoming commit.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
In the npcx i2c FIFO mechanism, the hardware will release SCL bus
immediately after the driver reads data from FIFO. That's why we need
to hold SCL bus before configuring the next transaction. Once it was
done, the driver release the bus for the next transaction.
But during the last transaction, the driver releases SCL first then
starts a STOP condition. At this moment, the SCL is pulled high by PU
resistance and driven to low for generating STOP condition later. This
additional clock might influence some i2c devices if they don't reset
their state machine after receiving STOP.
This CL fixes this issue by two steps:
1. Distinguish that it's the last read transaction with STOP condition?
2. If so, issue STOP condition before reading FIFO instead of holding
SCL bus. Then the hardware will generate it immediately after reading
FIFO.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Convert from device_get_binding to DEVICE_DT_GET. In doing this we
no longer need the label in the devicetree node so we remove that.
Removed all __ASSERT_NO_MSG(clk) since we'll get a build error if
DEVICE_DT_GET cant be satisfied, and the clock control api's will
handle reporting if the device_is_ready.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A recent patch removed use of the cfg structure, but left a pointer to
it defined which causes build failures.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add some simple depends so we limit various I2C drivers to the SoC
families that the drivers are relevant to.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
On I2C V1 parts, LL_I2C_EnableIT_TX() translates to EVT and BUF
IRQ enabling.
In stm32_i2c_msg_write function, LL_I2C_EnableIT_TX is called right
after stm32_i2c_enable_transfer_interrupts which already enables BUF
IRQ, which starts the transfer.
As a consequence it could happen that transfer is already complete
at the time LL_I2C_EnableIT_TX is called. This case is not expected
by remaining part of the code which loops forever waiting for BUF IRQ
to be raised.
Remove the superfluous LL_I2C_EnableIT_TX call.
Fixes: #32265
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The callback pointers for uninitiated operations are implicitly null;
making them explicit only confuses maintainers searching for drivers
that implement the API.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This CL prevents the transaction result overwritten by the recovery
function. Even if the recovery mechanism succeeds, the upper layer still
needs to know why the transaction failed.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Since all fields' type in SMBST is R/W1C and RO, setting a single bit to
clear a specified event is a more suitable solution. Or we might clear
the other pending bits that occurred at the same moment unexpectedly.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
This CL reset i2c event-completed semaphore before starting
transactions. Some interrupt events such as BUS_ERROR might change its
counter when i2c bus is idle. It causes that the driver cannot wait
for the event completed and return immediately.
Signed-off-by: Mulin Chao <mlchao@nuvoton.com>
Remove conditionals (PM_DEEP_SLEEP_STATES and PM_SLEEP_STATES) from
power management code. Now these features are always available when
power management is enabled.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Migrate the whole pm subsystem to use new power states information
from power_state.h and get states and residency properties from
device tree.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The default configuration is made to be "master" at
"standard speed". This makes it possible to use the
driver without having to configure it.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
