The context parameter used across device power management is
actually the power state. Just use it and avoid a lot of
unnecessary casts.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
First version of a driver for the st773r LCD controller.
Based on st7789v
Signed-off-by: Kim Bøndergaard <kim@fam-boendergaard.dk>
Signed-off-by: Kim Bøndergaard <kibo@prevas.dk>
Add a new display-inversion property to ili9xxx based display drivers to
send a "Display Inversion ON (0x21)" command during initialization.
This seems to be required for some ILI9xxx based displays to work
correctly, such as BuyDisplay ER-TFT028A2-4 (ILI9341 basd IPS display).
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Convert driver(s) to DEVICE_DEFINE instead of DEVICE_AND_API_INIT
so we can deprecate DEVICE_AND_API_INIT in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- Remove SYS_ prefix
- shorten POWER_MANAGEMENT to just PM
- DEVICE_POWER_MANAGEMENT -> PM_DEVICE
and use PM_ as the prefix for all PM related Kconfigs
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Use the core k_heap API pervasively within our tree instead of the
z_mem_pool wrapper that provided compatibility with the older mempool
implementation.
Almost all of this is straightforward swapping of one alloc/free call
for another. In a few cases where code was holding onto an old-style
"mem_block" a local compatibility struct with a single field has been
swapped in to keep the invasiveness of the changes down.
Note that not all the relevant changes in this patch have in-tree test
coverage, though I validated that it all builds.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Make driver generic for multiple ILI displays. The adopted strategy is
to share all driver code except register initialization, which has been
found to have some specific registers/values depending on the
controller.
The driver has been adjusted to support multiple compatibles.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
For drivers that support CONFIG_DEVICE_POWER_MANAGEMENT there are some
cases that look like:
#ifdef CONFIG_DEVICE_POWER_MANAGEMENT
DEVICE_DEFINE()
#else
DEVICE_AND_API_INIT()
#endif
There is no need to special case this as the pm_control_fn argument to
DEVICE_DEFINE will just be ignored in the
!CONFIG_DEVICE_POWER_MANAGEMENT case. So we can cleanup the code a
little and remove the #else cases for the drivers that do this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Align register names with the ones found in the datasheet. It is easier
to follow datasheet if names are the same.
Some other minor enhancements have also been introduced (comments, use
BIT for bit fields...).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Remove two operation flags in the SPI configuration
instance, which disturb software controlled chip select
lines (CS never gets released).
Signed-off-by: Marco Peter <marco@peter-net.ch>
This change allows to use SSD1306 based displays to be used on the
SPI bus as well.
Adding SPI shield.
Tested on SSD1306 and SSD1309 based displays using I2C.
Tested on SSD1309 based display using SPI.
Signed-off-by: Marco Peter <marco@peter-net.ch>
This change removes the interleaving control
frames.
Additionally all I2C accesses are centralized in
one single function.
Signed-off-by: Marco Peter <marco@peter-net.ch>
Remove Adafruit/Seeed TFT hardcoded settings. Note that undocumented
ILI9340/1 settings have been removed (maybe Seeed is using another ILI
variant?).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Move pixel format setting (RGB565/RGB888) to DeviceTree. Add support for
changing pixel format at runtime.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Multiple enhancements towards better code readability and consistency:
- sorted headers
- define and reference magic constants
- adjust some names
- add U suffix to unsigned constants
- move hw reset to a function
- remove non-needed initialization code from seeed tft
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Added extra asserts to write function of SDL display driver to check if
write is within bounds.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
The gd7965 driver still called ksleep with unsigned integers.
Use the K_MSEC makro instead.
Signed-off-by: Tobias Schaffner <tobiasschaffner87@outlook.com>
Appropriate WS can be loaded automatically if
the display controller has integrated temperature
sensor or an external sensor is connected.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
The driver-specific config_info structure referenced from the device
structure is marked const. Some drivers fail to preserve that
qualifier when casting the pointer to the driver-specific structure,
violating MISRA 11.8.
Changes produced by scripts/coccinelle/const_config_info.cocci.
Some changes proposed by the script are not included because they
reveal mutation of state through the const pointer, though the
code works as long as the driver-specific object is defined without
the const qualifier.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
