uart_async test and spi_loopback test require UART and SPI
with an ASYNC option.
The SAM0 UART/SPI driver requires configuring DMA support.
Arduino MKRZero is not DMA configured like other SAM0 boards.
We exclude it from the tests.
ea36f9b and f4c5bdf already exclude other SAM0 boards from these tests.
Arduino MKRZero also followed these PR policies.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@fujitsu.com>
This PR adds support for the RT1060_EVKB as a variant of the RT1060 EVK.
Blinky app tested locally on RT1060_EVKB.
Signed-off-by: Nickolas Lapp <nickolaslapp@gmail.com>
This sets the dts of dma for using the uart 6 asynch api.
The stm32f746 has a dma V1 with request 5 for Tx/Rx usart6
The Tx&Rx pins (PG14, PG9) of the usart6 are connected
on the nucleo_f746zg board to pass the test
The CONFIG_DCACHE=n must also be set to disable Dcache.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This sets the dts of dma for using the uart 6 asynch api.
The stm32f767 has a dma V1 with request 5 for Tx/Rx usart6
The Tx&Rx pins (PG14, PG9) of the usart6 are connected
on the nucleo_f767zi board to pass the test
The CONFIG_DCACHE=n must also be set to disable Dcache.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
As now the CONFIG_NOCACHE_MEMORY is not responsible for controlling the
data cache on STM32H7 SoC, the CONFIG_DCACHE=n must be set explicitly
to preserve previous behavior as UART driver is not using no-cache
buffers.
Considering the above comment, the CONFIG_NOCACHE_MEMORY can be safely
removed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
In order to bring consistency in-tree, migrate all tests to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
if DMA support is not present, LPUART driver will not compile when async
API support is required. Skip test cases when dma support is not present
and LPUART driver is enabled.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
add nxp,loopback mode to boards with LPUART. This will enable testing
the UART async api without a physical loopback connection.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
define uart peripheral that can be connected as a loopback using
external jumper for all boards this test can be run against.
Additionally, all RT boards require DMA memory to be noncacheable. Move
SRAM to DTCM for all RT10xx series boards, and to noncacheable OCRAM for
RT11xx series.
Signed-off-by: Daniel DeGrasse <daniel.degrasse@nxp.com>
Some names of the test cases are duplicated within the project.
This commit contains the proposed names of the test scenarios.
Signed-off-by: Katarzyna Giadla <katarzyna.giadla@nordicsemi.no>
This update Atmel sam serial drivers to use pinctrl driver and API. It
updates all boards with new pinctrl groups format.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Intention of the test is to abort rx few bytes after start of
transmission (before it is completed). Previously, thread was busy
waiting after start of TX and aborted RX from that context. However,
it may happen that CPU is busy handling UART transfer and
k_busy_wait prolongs beyond full transfer which results in test
failure.
Move rx_abort to k_timer timeout which is run in interrupt
context.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add a test case that ensures that uart_rx_enable() can be successfully
called after RX is disabled with uart_rx_disable() and also when it is
disabled automatically after the provided RX buffer is filled up.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add the pinctrl state name (default) for the UART/USART/LPUART
peripherals. Changes performed using the following Python script run
from the repository root:
```
from pathlib import Path
import re
for fpath in Path(".").glob("boards/arm/**/*.dts"):
lines = open(fpath).readlines()
is_stm32 = False
for line in lines:
if "stm32" in line:
is_stm32 = True
break
if not is_stm32:
continue
with open(fpath, "w") as f:
for line in lines:
f.write(line)
m = re.match(r"(\s+)pinctrl-0.*us?art.*", line)
if m:
f.write(m.group(1) + "pinctrl-names = \"default\";\n")
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Updated uart_rx_enable() and uart_tx() to use timeout given
in microseconds. Previously argument was given in milliseconds.
However, there are cases when milliseconds granularity is not
enough and can significantly reduce a throughput, e.g. 1ms is
100 bytes at 1Mb.
Updated 4 drivers which implement asynchronous API. Updated
places where API was used.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This commit corrects the DMA channels for the asynchronous
UART API testing support on the SAM R21 Xplained Pro board.
Signed-off-by: Ron Smith <rockyowl171@gmail.com>
It enables the usart6 to run the testcase with a DMA
tests/drivers/uart/uart_async_api. DMA2 (of type V1)
is configured on channel 5 (request) streams 7 & 2.
USART Tx and Rx PG14 - PG9 pins (14 & 16 of CN10)
are connected to PASS the test.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This sets the dts of DMA for using pn the uart 2 i.
The stm32h723 has a DMAMUX and request are 44 and 43 for usart2
The Tx&Rx pins PD5 and PD6 of the usart2 are connected
on the nucleo_h723zg board to pass the test
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Move to CMake 3.20.0.
At the Toolchain WG it was decided to move to CMake 3.20.0.
The main reason for increasing CMake version is better toolchain
support.
Better toolchain support is added in the following CMake versions:
- armclang, CMake 3.15
- Intel oneAPI, CMake 3.20
- IAR, CMake 3.15 and 3.20
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
Add configuration for testing the usart3 through the dma1
on the nucleo_l152re target.This test requires the Tx pin
to be connected to the RX pin on the board.
Pin definition is added for this usart instance.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Based on the new bindings for the stm32 dma feature,
the overlay for enabling the dma on uart client is modified.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit configures usart3 to use dma in uart_async_api test
on nucleo_l552ze_q platform.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
This commit configures usart3 to use dma in uart_async_api test
on stm32l562e_dk platform. Short pin2(PC10) & pin 3 (PC11) of usart3
in CN4 connector on stm32l562e_dk platform.
Signed-off-by: Krishna Mohan Dani <krishnamohan.d@hcl.com>
Adds nucleo_g071rb board to the uart_async_api test.
Therefore additionally add usart1 in board definitions.
Signed-off-by: Thomas Stranger <thomas.stranger@outlook.com>
The SAM0 uart driver requires dma configured for async support and
the uart async support assumes all UARTs support async. None of the
atmel SAM0 boards are configured this way and thus the tests will
not currently build for these boards.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This sets the dts of dma for using the uart asynch api.
The stm32l475 has a dmamux with request 2 for Tx/Rx usart4
The Tx&Rx pins (PA0, PA1) of the usart4 are connected
on the disco_l475_iot1 board to pass the test.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit adds the asynchronous UART API testing support on the
nucleo_l4r5zi board.
The usart3 module is used as the secondary loop-back UART, which is
required to run this test.
Signed-off-by: Shlomi Vaknin <shlomi.39sd@gmail.com>
After finish transmitting some bytes might be in the
peripheral receive register, since the transmition
is still happening after reception disabled.
This patch ensures that the peripheral has no
bytes in its internal state.
Signed-off-by: Shlomi Vaknin <shlomi.39sd@gmail.com>
Added gpio_loopback to indicate that test requires pins to be
shorten. This allows to filter out tests on setup which does
not have pin setup.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Extend the test_single_read test case to catch RX_RDY events that are
not expected to appear.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The cached device pointer must be placed in memory that allows user
mode invocation of the test functions to access it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a build only test to validate correct compilation of the uart_rtt
driver. No harness that connects to RTT is defined, and therefore the
test can't be run by CI.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The device pointer is now provided to the callback, there is no need to
call uart_callback_set() with the device being set a user data.
Fixes#26923
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
... because it is (required).
This makes a difference when building with CMake and forgetting
ZEPHYR_BASE or not registering Zephyr in the CMake package registry.
In this particular case, REQUIRED turns this harmless looking log
statement:
-- Could NOT find Zephyr (missing: Zephyr_DIR)
-- The C compiler identification is GNU 9.3.0
-- The CXX compiler identification is GNU 9.3.0
-- Check for working C compiler: /usr/bin/cc
-- ...
-- ...
-- ...
-- Detecting CXX compile features
-- Detecting CXX compile features - done
CMake Error at CMakeLists.txt:8 (target_sources):
Cannot specify sources for target "app" which is not built by
this project.
... into this louder, clearer, faster and (last but not least) final
error:
CMake Error at CMakeLists.txt:5 (find_package):
Could not find a package configuration file provided by "Zephyr" with
any of the following names:
ZephyrConfig.cmake
zephyr-config.cmake
Add the installation prefix of "Zephyr" to CMAKE_PREFIX_PATH or set
"Zephyr_DIR" to a directory containing one of the above files. If
"Zephyr" provides a separate development package or SDK, be sure it
has been installed.
-- Configuring incomplete, errors occurred!
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
This commit adds the asynchronous UART API testing support on the SAM
E54 Xplained Pro board.
The SERCOM1 module is used as the secondary loop-back UART, which is
required to run this test.
Note that no external UART loop-back connection is necessary to run
this test, because the SERCOM1 UART TX and RX pads are configured to be
internally connected; it is, however, still necessary to configure the
pinmux because the module pads are not connected until the pinmux is
configured.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Convert DT_UART_{0,1}_NAME to DT_NODELABEL() references as the cases are
board specific and this allows us to remove DT_UART_{0,1}_NAME defines
in dts_fixup.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
