In this commit, a config.h header file is added to support the case
when the NET_CONFIG_SETTINGS is not used. main.c is also modified to
enable platforms that do not support IPv6. These changes are necessary
in order to allow cc3220sf_launchxl support.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Sample code for AMS (Austria Micro Systems) ENS210 temperature and
relative humidity sensor.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Sample code for AMS (Austria Micro Systems) Indoor Air Quality Sensor
reading VOC and equivalent CO2 values.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
In order to generalize the currently specialized nRF51 IC setup hook,
make the following changes:
- Generalize the hook to bt_ic_setup()
- Use a weak NOP version by default
- Move the currently existing one to the board folder
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Enable the GPIO reset pin feature of nrf52840_pca10090
on pin P1.02 and the wait NOP feature of the controller.
These are used to let nrf9160_pca10090 synchronize the
HCI communication with nrf52840_pca10090 controllers.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
The patch provides flash offsets appropriate for running
this sample on nrf9160_pac10090 targets.
As that sample is small one, it is done with assumption that image_1
flash partition is empty.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Write protection was not disabled prior erase call.
It used to work before only because nrf driver had not check
the protection before erase execution. This behavior was changed in
order to align to zephyr - which implied requirement for this test fix.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
To support mass storage over USB in RAM we need a board with
sufficient RAM. Fix failing tests for boards with low memory.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Enable harness so we can execute smoke tests on the hardware with
command line:
sanitycheck --device-testing --device-serial /dev/ttyACM0 -p <BOARD>
-T samples/subsys/usb/hid
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Fixed using chipselect with seperate chipselect GPIOs and how they were
referenced from/in DeviceTree.
Also configure the device during initialization so it's ready to go
after init.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
Project configuration to run the CAN sample with the MCP2515 attached
via SPI as the CAN controller.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
This commit enable Bluetooth SMP Service which will help
us to do Device Firmware Upgrade over thr air. By default
it is not enable.
Reference: $zephyr/samples/subsys/mgmt/mcumgr/smp_svr
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
Add config overlay for cdc_acm+dfu composite configuration.
Manual configuration over menuconfig may be error-prone for
the user because then FLASH_LOAD_OFFSET and FLASH_LOAD_SIZE
should also to be set to appropriate values.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
In order to fit in SRAM, reduce the CONFIG_BT_MAX_CONN from 20 to 16 in
the configuration used for the BBC micro:bit.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Implement the Controller counterpart to CONFIG_BT_WAIT_NOP so that it
issues a NOP Command Complete event after booting up, to signal to the
Host that it is ready to receive HCI traffic.
Fixes#15333
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Currently coverage is enabled only in platforms which dont have
multiple memory regions. This sample was designed to emulate
different memory regions. This in conjunction with gcov which
might instrument data in different memory regions will not work
as expected. Therefore disabling gcov for this sample.
Fixes: GH-15107
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
We have actual tests now under tests/kernel/mem_protect/userspace
and tests/kernel/mem_protect/mem_protect that exercise all the
memory domain APIs. This old test is superfluous.
Fixes: #15178
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Unlike CONFIG_HW_STACK_PROTECTION, which greatly helps
expose stack overflows in test code, activating
userspace without putting threads in user mode is of
very limited value.
Now CONFIG_TEST_USERSPACE is off by default. Any test
which puts threads in user mode will need to set
CONFIG_TEST_USERSPACE.
This should greatly increase sanitycheck build times
as there is non-trivial build time overhead to
enabling this feature. This also allows some tests
which failed the build on RAM-constrained platforms
to compile properly.
tests/drivers/build_all is a special case; it doesn't
put threads in user mode, but we want to ensure all
the syscall handlers compile properly.
Fixes: #15103 (and probably others)
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
More buffers are need to build for sam_e70_xplained board
to work out of the box. Added board specific conf file.
Fixes#15096
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Patch 8af3df3519 changed logic and did not take into account 2 extra
bytes.
...
Precise data bus error
BFAR Address: 0x766e4900
***** Hardware exception *****
Current thread ID = 0x200004e8
Faulting instruction address = 0xddf4
Fatal fault in thread 0x200004e8! Aborting.
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Merge cb_usb_status_composite and cb_usb_status and use common
forward_status_cb for both composite and normal devices.
Fixes#14882
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
telnet_console driver is not compatible with new shell module, hence is
not working. Switch the telnet sample to use new TELNET shell backend.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
net_pkt_sendto uses size_t as parameter for len so the value would be
treat as unsigned which may cause and invalid memory to be read.
Fixes#14950#14955
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch enables the GPIO driver by default on all boards equipped
with an nRF SoC (all boards having `CONFIG_SOC_FAMILY_NRF=y` in their
`_defconfig` file).
In vast majority of cases the driver is needed, so it is more
convenient to enable it at board level than in particular
applications.
And if the driver is undesired for some reason, it can be still
disabled in the application config.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
There are two sensor samples be modified for a more explicit log when
no sensor connected or not connected correctly. Rather than a horrible
hardware fault, which may misleading beginner.
1. bme280
2. sx9500
Signed-off-by: Aaron Tsui <aaron.tsui@outlook.com>
Updated test harness to check for a second instance of
"Watchdog sample application". This is to confirm the
board did reset itself.
Signed-off-by: Cinly Ooi <cinly.ooi@intel.com>
The IV Index is always a 32-bit value, so using u16_t for it was
confusing. Create a define for it, similar to other constant values,
to get rid of this confusion.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
