The pga enum internal reference voltage and gain values
were fixed in the code, but a comment was forgotten to be
updated. Correct the comment to match how the code uses
the enum.
Signed-off-by: Ryan McClelland <ryanmcclelland@meta.com>
Add a property to the ADC channels which allows the configuration
of the current source pin.
Signed-off-by: Benedikt Schmidt <benedikt.schmidt@embedded-solutions.at>
Define two macros for calibration and oversampling for STM32 series that
possess these features, and use these macros instead of a list of series.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Rework oversampling by creating a const table containing possible
oversampling values and using this table instead of switch case.
Also disable ADC for all series before setting oversampling.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Renesas Renesas SmartBond(tm) have two ADC blocks:
GPADC and SDADC.
This change adds drivers for both.
Each ADC supports only one channel setup, drivers allow
to have multiply channels in sequence. Switching
between ADC sources in done in software.
GPADC has 10 bit resolution (accuracy can be increase
with oversampling). Values up to 3.6V can be measured
on selected pins. V30 and VBAT1 can also be measured.
SDADC has 14 bit resolution and can take measurements
from 8 pins (single of differential) and VBAT.
Signed-off-by: Jerzy Kasenberg <jerzy.kasenberg@codecoup.pl>
Several sections of the STM32 ADC driver are #ifdef by a combination of the
same SOC defines that share similar IPs. These are F2/F4/F7/L1, and
F1/F37x.
Each of these combinations is now replaced by a specific compatible, which
makes the code a bit lighter and more succinct.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Add ifdef around some functions that don't exist for STM32F37x (ADC_V2_5)
like it is done for STM32F1x.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Inverts the logic of some #ifdef, replacing lists of newer series by a
list of NOT older series. This makes it shorter, and more future-proof as
future series are more likely to work out of the box, without need to
manually add a new define in each place.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Some STM32 families that need to check the ADRDY flag after enabling the
ADC were not doing it. The #ifdef has been updated to fix that.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Use the new dts properties for sampling time in the STM32 ADC driver:
- Get the sampling time from dts
- Remove all sampling time macro concatenation.
- Simplify/refactor setting of sampling time
- Check that sampling time is the same for all series using common channel
This also fixes a few cases where wrong sampling times were used for an
ADC instance (like ADC4 on U5, or ADC3 on STM32H723).
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
Renamed CONFIG_ADC_GECKO to CONFIG_IADC_GECKO to eliminate confusion
between the Incremental ADC found on series 2 silabs gecko MCUs, and the
ADC found on earlier gecko series.
Signed-off-by: Jared Baumann <jared.baumann8@t-mobile.com>
Make use of positive status values in the DMA callback to pass
info to the DMA client after a successful DMA operation.
A completed DMA transfer uses the status 0 while a reached
water mark uses the status 1.
Signed-off-by: Cyril Fougeray <cyril.fougeray@worldcoin.org>
SPI configuration did not set bit ordering or more importantly the clock
polarity which seemed to be misconfigured. Setting this corrects one more
quirk when working with this part on the TDK Robokit1
Signed-off-by: Tom Burdick <thomas.burdick@intel.com>
To be consistent with the current NXP clocking scheme,
move the LPADC clocking code to the SOC files where
all of the other peripheral clocking is done.
Also remove any other SOC-specific code to the
respective SOC file and out of this driver.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Code for power level property was accidentally
removed by accident from driver in commit 9921c59f40
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
- This includes the driver, test app, and sample app
- Only the boards\arm\cy8cproto_062_4343w board is supported for now
Signed-off-by: Bill Waters <bill.waters@infineon.com>
Simplify the STM32 ADC driver code by using the new ADC resolutions
property in dtsi files.
Signed-off-by: Guillaume Gautier <guillaume.gautier-ext@st.com>
- Remove build asserts in favor of DT enums
- Remove power level property since it is unused by SDK
- Correct voltage ref value in DT to correspond to
chip specific values documented in reference manuals
instead of corresponding to SDK enum names.
- Fix SOC devicetrees affected by these changes.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
port commit f7f47dc to stm32h5
Without this fix, ADC driver will hang when reading internal channels.
Signed-off-by: Brian Juel Folkmann <bju@trackunit.com>
The MCUX platform always uses pinctrl, there's no need to keep extra
macrology around pinctrl. Also updated driver's Kconfig options to
`select PINCTRL` (note that some already did).
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This commit adds the Gecko IADC driver and support for it to the
efr32bg_sltb010a board.
Signed-off-by: Mateusz Sierszulski <msierszulski@antmicro.com>
Signed-off-by: Roman Dobrodii <rdobrodii@antmicro.com>
Move semicolon from end of DT_INST_FOREACH to DEVICE_DT_INST_DEFINE
to make multi-instancing possible. This caused some problems with
CI after adding adc node to native_posix dts.
Signed-off-by: Benjamin Björnsson <benjamin.bjornsson@gmail.com>
Remove all init functions that do nothing, and provide a `NULL` to
*DEVICE*DEFINE* macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The below is the unit test result for the driver and kernel of
it82xx2_evb board.
GPIO/gpio_basic_api: PASS
I2C/i2c_api: PASS
Flash: PASS
UART/uart_basic_api: PASS
PWM/pwm_api: PASS
WDT/wdt_basic_api: PASS
KSCAN/kscan_api: PASS
kernel/sched/schedule_api: PASS
kernel/sched/preempt: PASS
kernel/timer/timer_api: PASS
kernel/sleep: PASS
ADC/adc_api: PASS.
ADC note: conversion time~=61.6us
sample time delay~=60us
wait voltage stable time~=202.8us
Set sampling time to 500us will pass for ADC test.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
MISRA Rule 5.7 requires uniqueness of tag identifiers. Shell is
frequently problematic because many code uses `const struct shell
*shell`. This causes CI noise every time one of these shell files is
edited, so let's update all of them with `const struct shell *sh`
instead.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
add support for async call and repeat sample test
1. change the DMA req to 2 byte each
2. increase the buffer pre-dma
3. add protection on invalid buffer
depends on: PR #56104
fixing: issue #56070
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Removes a workaround that was required while there was a bug in
upstream STM32 HAL drivers where the oversampling was not set
correctly in all cases. This has since been fixed, and also
added to the Zephyr STM32 HAL.
The upstream issue:
https://github.com/STMicroelectronics/STM32CubeH7/issues/177
Signed-off-by: Hein Wessels <heinwessels93@gmail.com>
The init infrastructure, found in `init.h`, is currently used by:
- `SYS_INIT`: to call functions before `main`
- `DEVICE_*`: to initialize devices
They are all sorted according to an initialization level + a priority.
`SYS_INIT` calls are really orthogonal to devices, however, the required
function signature requires a `const struct device *dev` as a first
argument. The only reason for that is because the same init machinery is
used by devices, so we have something like:
```c
struct init_entry {
int (*init)(const struct device *dev);
/* only set by DEVICE_*, otherwise NULL */
const struct device *dev;
}
```
As a result, we end up with such weird/ugly pattern:
```c
static int my_init(const struct device *dev)
{
/* always NULL! add ARG_UNUSED to avoid compiler warning */
ARG_UNUSED(dev);
...
}
```
This is really a result of poor internals isolation. This patch proposes
a to make init entries more flexible so that they can accept sytem
initialization calls like this:
```c
static int my_init(void)
{
...
}
```
This is achieved using a union:
```c
union init_function {
/* for SYS_INIT, used when init_entry.dev == NULL */
int (*sys)(void);
/* for DEVICE*, used when init_entry.dev != NULL */
int (*dev)(const struct device *dev);
};
struct init_entry {
/* stores init function (either for SYS_INIT or DEVICE*)
union init_function init_fn;
/* stores device pointer for DEVICE*, NULL for SYS_INIT. Allows
* to know which union entry to call.
*/
const struct device *dev;
}
```
This solution **does not increase ROM usage**, and allows to offer clean
public APIs for both SYS_INIT and DEVICE*. Note that however, init
machinery keeps a coupling with devices.
**NOTE**: This is a breaking change! All `SYS_INIT` functions will need
to be converted to the new signature. See the script offered in the
following commit.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
init: convert SYS_INIT functions to the new signature
Conversion scripted using scripts/utils/migrate_sys_init.py.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
manifest: update projects for SYS_INIT changes
Update modules with updated SYS_INIT calls:
- hal_ti
- lvgl
- sof
- TraceRecorderSource
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
tests: devicetree: devices: adjust test
Adjust test according to the recently introduced SYS_INIT
infrastructure.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
tests: kernel: threads: adjust SYS_INIT call
Adjust to the new signature: int (*init_fn)(void);
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
We get compile warnings of the form:
error: converting the result of
'<<' to a boolean; did you mean
'((__aeabi_ctype_table_ + 1)[(byte)] << 28) != 0'?
[-Werror,-Wint-in-bool-context]
if (!isprint(byte)) {
^
Since isprint (and the other is* functions) return an int, change check
to an explicit test against the return value.
Signed-off-by: Kumar Gala <kumar.gala@intel.com>
Add the support of the new stm32h5 to the stm32 ADC driver
Note : LL_ADC_CLOCK_ASYNC_DIV6 is the value for getting the
expected results of ADC.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Replace pointer construction macro with value from config struct.
Fixes what appears to be an oversight from #55522.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Unify the drivers/*/Kconfig menuconfig title strings to the format
"<class> [(acronym)] [bus] drivers".
Including both the full name of the driver class and an acronym makes
menuconfig more user friendly as some of the acronyms are less well-known
than others. It also improves Kconfig search, both via menuconfig and via
the generated Kconfig documentation.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
After enabling the ADC, the peripheral has a certain delay (about 1ms)
to set its ADC Ready flag in the ADC ISR register.
In between, the ADRDY is still 0 and the ADEN is 1 in the CR.
The ADC can be used for conversion, only when the ADRDY bit is set
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Microchip XEC ADC and ADC V2 driver were merged into one
That PR did not change the ADC API test and ADC shell resulting
in twister build failures. Fixed both ADC API test and ADC shell.
Signed-off-by: scott worley <scott.worley@microchip.com>
Deleted adc_mchp_xec.c and microchip,xec-adc.yaml file.
DTSI, yaml, CMakeLists.txt and Kconfig.xec files are
updated for compatible.
Signed-off-by: Manimaran A <manimaran.a@microchip.com>
