Removed get_report_cb as it was an incorrect implementation
of Get_Report request. Correct response would be returning
current report value, not report descriptor.
Signed-off-by: Marcin Szymczyk <Marcin.Szymczyk@nordicsemi.no>
Currently there is a mixed approach in prefixes from mbedTLS
configuration (MBEDTLS_ and TLS_). The latter was used in generic config
file and could bring up confusion that it can only be used with TLS
subsystem. Hence unify the approach to MBEDTLS_ prefix to avoid such
confusion.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
STM32 uart Kconfig instance flags were not following
same naming scheme than other drivers (i2c, spi, ..)
Update driver to use UART_X instead of UART_STM32_PORT_X
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Added right button, X and Y axis movement to HID mouse example.
Enabled only if board has enough buttons.
Added LED toggling notification when report is sent.
Signed-off-by: Marcin Szymczyk <Marcin.Szymczyk@nordicsemi.no>
Check result of fcntl() to catch any regressions in fcntl() handling
in Zephyr. To facilitate this, also merge block() and nonblock()
functions into single setblocking().
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Current application data size in echo_client sample does not fit into a
single datagram with DTLS enbled for default IPv6 MTU (1280 bytes). This
caused abrupt failure of the sample with DTLS enabled over 802.15.4 L2.
Decreasing the application data size allows it to fit into a single UDP
datagram after encapsulating it into DTLS record.
Additionally, finetune DTLS timeout on echo_server to match UDP
application timeout on echo_client (so that a single datagram loss
does not cauase DTLS session to end).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Now if Server receives re-transmitted messages from client then
it will not get completely ignored but respective GET & Publish
message will get release from Server side.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
As per Mesh Model Specification,
when a Server receives a Set message or a Set Unacknowledged message,
it shall set the state to the target field of the message,
unless the message has the same values for the SRC, DST, and TID
fields as the previous message received within the last 6 seconds.
This commit take care of this requirement.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
POSIX doesn't mandate such a header, only <fcntl.h>. <sys/fnctl.h>
is just an internal implementation detail of Newlib on which we should
not rely.
This makes it possible to build this sample against minimal libc.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Considering that IP can be set dynamically by DHCP
or statically before test previously, we could have
alternative way by supporting both setting IP and
existing IP.
Signed-off-by: Bub Wei <bub.wei@unisoc.com>
Since the Arduino 101 and the Quark SE C1000 are not actively developed
boards, default to other boards that are maintained and used.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit's implementation update Vendor Model dummy response
value in vnd_get() instead of vnd_set_unack().
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
Removed bug which get introduced by PR:9521. Because of it
not able to save App's variable on SoC flash.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
The OpenAVNU gPTP daemon repository has changed so the compile
instructions were not working.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Do not limit to whitelisted boards, instead make it build/run for any
board that defines required DTS macros.
Simplified documentation and made it more generic. Remove HW setup and
made sample work with built-in LEDs and buttons.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Do not limit to whitelisted boards, instead make it build/run for any
board that defines required DTS macros.
Remove QMSI kconfigs and depend on DTS only.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Do not limit to whitelisted boards, instead make it build/run for any
board that defines required DTS macros.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Do not limit to whitelisted boards, instead make it build/run for any
board that defines required DTS macros.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
1. Modified fade_led PWM example to include
nRF HW PWM option.
2. Added fade_led nrf52_pca10040.overlay
in order to enable PWM node and choose
output PWM GPIO for channel 0. Channel 1
GPIO enable but not used in sample src.
Signed-off-by: Gaute Gamnes <gaute.gamnes@nordicsemi.no>
The Code need to be align after introduction of stream codec to
setting serialization subsystem.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Remove QEMU instructions as those do not work. Add native_posix
board instructions for running gPTP with linuxptp daemon.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This sample was creating objects from header file in the bss.
Fixed it by moving the objects to appropriate object files.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
This sample provides an example for using the code relocation
feature. This example will place text,data,bss from 3 files to
various parts in the SRAM. For this a custom linker file is used
which is derived from include/arch/arm/cortex_m/scripts/linker.ld.
Signed-off-by: Varun Sharma <varun.sharma@intel.com>
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
We get an intermittent fail when running on qemu_xtensa. Disable this
sample for now on that platform to allow sanitycheck / CI to pass for
other PRs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Use generic logging macros LOG_*() instead of NET_*() as the
latter are mostly meant for internal networking stack use.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove network specific default and max log level setting
and start to use the zephyr logging values for those.
Remove LOG_MODULE_REGISTER() from net_core.h and place the
calls into .c files. This is done in order to avoid weird
compiler errors in some cases and to make the code look similar
as other subsystems.
Fixes#11343Fixes#11659
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add Bluetooth, 802.15.4 and OpenThread overlay configurations to socket
echo_client and echo_server samples.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Sample application to demonstrate usage of cmsis_rtos_v1 APIs
with dining philosopher's problem implementation.
This covers semaphores, mutex and thread APIs of CMSIS RTOS V1.
Signed-off-by: Spoorthi K <spoorthi.k@intel.com>
Corrected state binding. With this commit Light Lightness
actual state would not cross its upper & lower limit.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
