Use gpio_pin_t uniformly when passing pin indexes to the driver. Use
gpio_flags_t uniformly when passing flags to the driver. Change name
of pin configuration function in API function table to be consistent
with other API functions.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
There is a typedef used to store pin indexes in configuration
structures. For consistency it should also be used to identify pin
indexes in function prototypes.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The only remaining port operations have dedicated API function table
entries. Remove the defines for access op (mode), and remove support
for access op from all implementations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The last external reference to these was removed when the pin
write/read functions were deprecated. Remove the syscall support, API
function table entries, and implementation from all drivers.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
These have been replaced by the appropriate call to
gpio_pin_interrupt_configure(). While the disable function could be
implemented using the new functionality, the enable function cannot
because the interrupt mode is not available. Consequently we cannot
replace these with equivalent functionality using the legacy API.
Clean up the internal implementation by removing the inaccessible
port-based enable/disable feature, leaving the pin-based capability in
place.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This API will be deprecated in favor of the new API that clearly
specifies whether it works on logical or physical levels.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure. This driver uses fixups to define a common name
based on the SOC series; until aliases for the new properties are
added the code assumes all pins are supported.
Since pin ordinal validation is now done directly in gpio API,
remove checks inside the driver itself.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the hard-coded device-specific pin count to
initialize it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it. Not all aliases appear to be present, but using instances breaks
because the ports used by different boards do not always start with
the first.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure. The devicetree binding does not inherit from
gpio-controller, so the required property is not available there. A
hard-coded value of 32 pins has been implemented to make the driver
function.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure. This driver uses fixups to define a common name
based on the SOC; until aliases for the new properties are added the
code assumes all pins are supported.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a config structure for each port and use the devicetree GPIO pin
count to initialize it. Simplify device initialization by using
instance number as only variation point.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the common data structure with the common config structure as
a prefix of the driver-specific config structure and use the
devicetree GPIO pin counts to initialize it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Extend the driver data structure with a field that identifies the pins
supported by the device. Document the fields and who is responsible
for maintaining them.
Update all configuration functions for specific pins to return an
error if the pin is not supported.
Update all set/get functions for specific pins to assert if the pin is
not supported.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This breaks down the GPIO controller definition in DTS into
multiple entries. This allows these controllers to be
referenced by other DTS, and test board overlay files.
And also we can remove the entries in the dts fixup file.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Update driver code to use new GPIO configuration flags such as
GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The public API for GPIO flags should use unsigned values, and for
MISRA compliance the size should not be platform-dependent. Add a
typedef for generic flags.
Also add typedefs for pin indexes and devicetree flags so these can
be safely recorded from devicetree property values without risking
loss of information if more flags are added in the future.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This commits adds GPIO driver for LiteX SoC builder.
Due to the fact that GPIO in LiteX is unidirectional and can be
configured with different pins amount per port, additional entries
were added to the dts file.
Signed-off-by: Robert Winkler <rwinkler@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
IO extenders may provide input signals to LEDs or sensors where
leaving the signal undriven may result in increased power consumption
or misbehavior. The SX1509B powers up with all signals configured as
inputs. Provide a way to indicate which pins should be set as output,
and their initial signal level, when the device is configured.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The cached state of the output must be managed under mutex, but the
original toggle implementation read the current state outside the
mutex and used it to update the state. Rework the internal API so
that toggle is done within the mutex, distinct from masked set.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This factors the common bits of device declaration into macros
so it would be easier to add new instances.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Remove support for GPIO_ACCESS_BY_PORT in the config function
as configuration by port is going away.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Since the GPIO expander is a I2C device, any read/write to
the registers has high latency. Therefore, semaphore is
introduced to prevent multiple threads to manipulate
the GPIOs at the same time.
Also make sure that we are not doing I2C transactions
within ISRs.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Only update the internal register cache after successful write,
or else it would get out of sync with hardware.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The register pair for each port in the GPIO expander are
port 0 first then port 1. This would not work for big
endian systems with the u16_t port value. So need to
swap the byte ordering on such system.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The structures defined in the header file are only used by
the driver source file, and should not be used by others.
So roll the header file into the source file so it won't
get #include.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Use I2C burst write to write 2 bytes to each pair of registers
instead of 2 separate transactions of writing 1 byte.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
