Some device may need to be put up on CS high logic. The active low logic
is the default as usual, but it is now possible to request the active
high logic.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
EEPROM mode can be, in fact, asserted from tx_bufs/rx_bufs thus removing
it.
Fixes#5839
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Instead of using CONFIG_POLL, which is not directly related to SPI and
is a kernel option, let's have SPI_ASYNC instead. When enabled, it will
select POLL automatically.
Fixes#5839
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
tx_bufs/tx_count and rx_bufs/rx_count can be hold in another dedicated
structure, thus reducing the number of parameters to transceive. This
permits to avoid using the stack when calling transceive.
Since we saved parameters, we can expose back the struct device pointer,
to stay consistent with other device driver APIs.
Fixes#5839
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As the content of this struct will not be modified by drivers, it's
better to pass it as constant. Also, if someday struct device can be
made contant too, this change will make spi ready for registering the
spi_config into ROM directly.
Fixes#5839
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Some device include a temperature sensor, usually used as a
companion for helping in drift compensation, that measure the
die temperature. This temperature IS NOT related to the the
ambient temperature, hence a clean separation between the two
is required.
This commit introduces a clean separation between the two
types of temperature leaving the old deprecated definition
still there.
The list of current drivers that read the die (and not the ambient)
temperature is the following:
- adxl362
- bma280
- bmg160
- bmi160
- fxos8700
- lis3mdl
- lsm6ds0
- lsm6dsl
- lsm9ds0
- mpu6050
Signed-off-by: Armando Visconti <armando.visconti@st.com>
For posix layer implementation of message queue, we need to fetch
basic attributes of message queue. Currently this routine is not
present in Zephyr. So adding this routing into message queue.
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
User mode shouldn't be able to read/write to this memory directly,
needs to be done on its behalf by driver system calls.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The __net_if_align was removed in earlier commits but it needs
to come back as in some arch the alignment of net_if section
will be wrong.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Adapt the MyNewt non-volatile configuration system to become a settings
system in Zephyr.
The original code was modifed in the following ways:
* Renamed from config to settings
* Use the zephyr FCB, FS API, and base64 subsystems
* lltoa like function was added to sources as it was required but not
included in Zephyr itself.
* The original code was modified to use Zephyr's slist.h as single
linked list implementation.
* Reworked code which was using strtok_r, added function
for decoding a string to a s64_t value.
* Thank to the above the settings subsys doesn't require newlibc anymore.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
__packed allows the struct to be linked at a non-word size boundrary
which causes an unaligned access fault on the Cortex-M0+.
Signed-off-by: Michael Hope <mlhx@google.com>
There can be lot of traffic class threads and each will have
their own stacks. This can trigger issue when traversing the
stacks list in "net stacks" shell command. To overcome this issue,
we need to align each net_stack_info struct by 32 bytes. This is
the same issue that happened with net_if earlier.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add statistics for number of packets and bytes to each traffic
class. Print this information in net-shell.
Also make sure that we do not calculate total packet length many
times. So calculate network packet total length once and then use
that value instead of calculating it many times in a row.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
With this commit it is possible to add priority to sent or received
network packets. So user is able to send or receive higher priority
packets faster than lower level packets.
The traffic class support is activated by CONFIG_NET_TC_COUNT option.
The TC support uses work queues to separate the traffic. The
priority of the work queue thread specifies the ordering of the
network traffic. Each work queue thread handles traffic to one specific
work queue. Note that you should not enable traffic classes unless
you really need them by your application. Each TC thread needs
stack so this feature requires more memory.
It is possible to disable transmit traffic class support and keep the
receive traffic class support, or vice versa. If both RX and TX traffic
classes are enabled, then both will use the same number of queues
defined by CONFIG_NET_TC_COUNT option.
Fixes#6588
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Allow caller to create array of thread stacks using
NET_STACK_ARRAY_DEFINE() macro. This allows more debug information
to be printed by "net stacks" command.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add context option support and implement PRIORITY option that
can be used to classify the network traffic to different trafic
classes according to said priority value.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of always allocating both IPv6 and IPv4 address information
to every network interface, allow more fine grained address
configuration. So it is possible to have IPv6 or IPv4 only network
interfaces.
This commit introduces two new config options:
CONFIG_NET_IF_MAX_IPV4_COUNT and CONFIG_NET_IF_MAX_IPV6_COUNT
which tell how many IP address information structs are allocated
statically. At runtime when network interface is setup, it is then
possible to attach this IP address info struct to a specific
network interface. This can save considerable amount of memory
as the IP address information struct can be quite large (depends
on how many IP addresses user configures in the system).
Note that the value of CONFIG_NET_IF_MAX_IPV4_COUNT and
CONFIG_NET_IF_MAX_IPV6_COUNT should reflect the estimated number of
network interfaces in the system. So if if CONFIG_NET_IF_MAX_IPV6_COUNT
is set to 1 and there are two network interfaces that need IPv6
addresses, then the system will not be able to setup IPv6 addresses to
the second network interface in this case. This scenario might be
just fine if the second network interface is IPv4 only. The net_if.c
will print a warning during startup if mismatch about the counts and
the actual number of network interface is detected.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Move IP address settings from net_if to separate structs.
This is needed for VLAN support.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The ifdef'ing is re-ordering things so that the documentation is
either to far away from the implementation, or in the wrong
order (implementation and then documentation).
This commit reorders the macros and documentation so that we avoid
long-spanning #ifdef's and we keep the documentation at the head of
the implementation.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
As per the Apache v2 License, state changes made to the original code in
the modified version of the files.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Since base64 is such a simple and commonly used feature it makes no
sense to build the whole of mbedTLS for it. Instead take the
implementation that comes with mbedTLS and import it as a native library
outside of ext/ for all to use directly.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Create infrastructure that allows ethernet device driver to tell
if it supports network packet checksum offloading. This applies only
to IPv4, UDP or TCP checksums. The driver can enable/disable checksum
offloading separately for Tx and Rx network packets.
If the device (ethernet in this case) can calculate the network
packet checksum for IPv4, UDP or TCP, then do not calculate the
corresponding checksum by the stack itself.
Fixes#2987
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Modifies several functions that are causing wrong
behaviour.
* semaphore.h: add missing restrict keyword.
* sem_destroy(): check that nobody is waiting
before destroying the object.
* sem_timedwait(): simpify function logic and
fix a bug when abstime > currtime, that passed
ticks instead of ms to k_sem_take().
* sem_wait(): avoid unnecessary checks.
* sem_init(): add pshared value assertion.
Signed-off-by: Juan Manuel Torres Palma <j.m.torrespalma@gmail.com>
This was originally added as a work-around to avoid the heavy stack
consumption of the TinyCrypt PRNG when generating NRPAs. This is
no-longer an issue, and there are in fact no (in-tree) users of this.
Remove it before it gains any wider users, since it was in many ways a
hack/work-around to begin with.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In some cases the app may want to force using the identity address
regardless of privacy support or what type of advertising is done.
Provide such an option in bt_le_adv_param.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add freeaddrinfo() to complement getaddrinfo().
Existing applications using getaddrinfo() will usually free
allocated memory using freeaddrinfo(). Even if nothing is allocated
the function should exist to avoid having to change the application
when porting.
Signed-off-by: Stig Bjørlykke <stig.bjorlykke@nordicsemi.no>
Avoid listing internal function in the public API documentation. After
enabling those doxygen configs, we go lots of errors and bad refs that
were fixed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The k_mem_partition structs need to be placed in the kernel memory.
This patch ensures that these structs are placed correctly.
Also when a struct k_mem_domain is declared it is advised to add
__kernel.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
If CONFIG_NET_DEBUG_NET_PKT was enabled, then a call to
net_pkt_get_reserve_data() was calling wrong debug function
which caused compile error.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add support for MSG_PEEK flag in recv and recvfrom.
This flag is needed when using non-zephyr embedded applications with
Zephyr's socket API.
Signed-off-by: Stig Bjørlykke <stig.bjorlykke@nordicsemi.no>
