The way the nRF21540 device is configured makes sense once you
understand it, but it's quite unusual: a single peripheral is
configured with two separate devicetree nodes linked by a phandle.
Since this risks entering "exploding head" territory for beginners, it
deserves a thorough example. Add one to the binding's description.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This is a helper binding for radio front-end modules that have a
two-pin control interface, where one pin is used to turn on an power
amplifier (PA) for TX, and another is used to turn on a low-noise
amplifier (LNA) for RX.
Such hardware is already supported by the Bluetooth subsystem, but via
PA/LNA Kconfig settings. Since this is hardware configuration, it is
better to move this to devicetree instead.
Add a binding that makes it possible to define nodes which contain the
same information, along with a bit of extra information related to the
gain in dB of each amplifier not currently available from Kconfig.
This is similar to the existing binding for the nordic,nrf21540-fem
compatible.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Signed-off-by: Andrzej Kuros <andrzej.kuros@nordicsemi.no>
Clean up multi-line strings so they will show up properly in the
bindings index in the HTML documentation.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This is to support upcoming external radio coexistence implementations,
see binding documentation for more info.
Signed-off-by: Jonathan Rico <jonathan.rico@nordicsemi.no>
add ledc to board dtsi file,
change compatible and device define in pwm driver,
add yaml for board ledc support,
fix missing include for board in gpio include
Signed-off-by: Andrei-Edward Popa <andrei_edward.popa@upb.ro>
Use i2c_hal functions to enable support for
multiple SoCs.
Use DT compat to enable I2C from device
tree configuration
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
This joins all clock control handling to same source
by using hal clock functions. It also brings ESP32C3
clock support.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
In order to have Espressif SoCs working with
the same uart drivers, all low level functions
are now replaced to hal_espressif HAL calls.
This also changes pinmux, gpio and uart
init order to meet its dependencies.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
STM32WL could be either single core (stm32wlex) or
dual core (stm32wl5/4x).
Make CPU2 prescaler an optional property (while it will
be required if inherited from st,stm32wb-rcc.yaml.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Now that Kconfig option for STM32 clocks configuration has been
removed, set rcc properties as required.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Added watchdog implementation which is using counter device
to implement watchdog driver API. Watchdog timeout is called from
counter interrupt context. Some counter implementations support
using ZLI interrupt level which can be use here as well. Watchdog
like this can be used along hardware watchdog to cover for its
limitations, i.e. Nordic watchdog resets unconditionally after
62uS after triggering watchdog interrupt. It is not enough time
to dump logging data.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The FIU/UMA module in the NPCX chip provides an dedicated SPI interface
to access the SPI flash. This commit adds the driver support for it.
With this commit, the application can call the flash APIs
(via spi_nor.c) to access the internal flash of NPCX EC chips.
Signed-off-by: Jun Lin <CHLin56@nuvoton.com>
Change-Id: I32bbf09f6e014b728ff8e4692e48151ae759e188
Rewrite the NRFX IPC driver to properly support multi-channel addressing
leveraging the newly introduced MBOX APIs.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
One limitation of the current IPM API is that it is assuming that the
hardware is only exporting one single channel through which the data can
be sent or signalling can happen.
If the hardware supports multiple channels, the IPM device must be
instantiated (possibly in the DT) several times, one for each channel to
be able to send data through multiple channels using the same hw
peripheral. Also in the current IPM API only one callback can be
registered, that means that only one driver is controlling all the
signalling happening on all the channels.
This patch is introducing a new MBOX API that is supporting
multi-channel signalling and data exachange leveraging and extending the
previous (and outdated) IPM API.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
This is a driver for the Synopsys DesignWare MAC. It should work
with the "DesignWare Cores Ethernet Quality-of-Service" versions 4.x
and 5.x.
This driver uses a zero-copy strategy, meaning that the hardware
reads and writes data directly from/to packet fragment buffers
provided by the network subsystem without first copying the data into
a dedicated DMA bounce buffer.
Platform specific setup is necessary for the hardware to work.
Currently, only the STM32H7X series is implemented and tested.
While this part needs refinement, this driver performs better and uses
far less code space than the HAL-based alternative.
Not yet implemented:
- MDIO (it is WIP, currently relying on default PHY config)
- PTP support
- VLAN support
- various hardware offloads (when available)
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
MEC172x eSPI driver, eSPI pin programming, interrupt updates related
to eSPI and other updates for MEC172x eSPI driver.
Signed-off-by: Jay Vasanth <jay.vasanth@microchip.com>
Add a set of tests to check the API behavior. The API tests can only run
on a platform that does not have an actual pinctrl driver, e.g.
native_posix. The test itself implements a pinctrl mock driver and
provides the required "pinctrl_soc.h" header with required types/macros.
The implementation is used in the tests to verify the behavior of the
API or Devicetree macros.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
When using group based representation on pinctrl nodes, the pin
configuration properties end up being at the grand-children level, so
the `pincfg-node.yaml` file can't be used.
Having a common file that can be used for both cases would require
tooling changes, so for now a copy that operated at the grand-children
level has been created.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Initial skeleton for pinctrl drivers. This patch includes common
infrastructure and API definitions for pinctrl drivers.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move odr options from Kconfigs to Device Tree. Moreover add
in DT a power-mode option to select among 4 possible values
(PD, LP, HR, HF). The power mode cannot be currently set from
sensor APIs.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Create a common properties file that will be included by all DT
bindings (as i2c and spi) handled by lis2ds12 driver.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add a dedicated compatible for STM32MP1 clock control node.
Since, on such platform, clock configuration is done on A9
side, only the clock-frequency property is available.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add general mboxes, mbox-names to base.yaml to be utilized by any
clients that use mailboxes.
Additionally add mailbox-controller.yaml for common properties shared
by all mailbox controller devices.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Currently all the *-names and *-cells properties are derived from the
name of the base <name>s property. This is a limitation because:
- It forces the base property name to be plural ending in -s
- It doesn't allow the english exception of plural words ending in -es
With this patch we add one additional property 'specifier-space' that
can be used to explicitly specify the base property name.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Suggested-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The shared multi-heap memory pool manager uses the multi-heap allocator
to manage a set of reserved memory regions with different capabilities /
attributes (cacheable, non-cacheable, etc...) defined in the DT.
The user can request allocation from the shared pool specifying the
capability / attribute of interest for the memory (cacheable /
non-cacheable memory, etc...)
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Add specific properties to enable remap for PA11/PA12, which is a
possibility on STM32G0/F0 SoCs.
These properties only have effect when defined.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This name should be the same as cpus node in dtsi. After the power
policy is added, the cpu-power-states in the CPU properties can
be used.
Signed-off-by: Tim Lin <tim2.lin@ite.corp-partner.google.com>
AHB prescaler is a value which divides the SYSCLOCK
to provide the HCLK. The HCLK supplies the core, AHB bus, memory.
On the stm32wb and stm32wl, the HCLK for CPU1 is HCLK1
with cpu1-prescaler.
By default the value is 1, else the HCLK must be correctly set.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
interrupt controller, also places its relevant
peripheral sources allowing drivers to use the
DT macros instead of espressif headers.
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
This reverts commit d3a558591f.
We shouldn't be adding vendor prefixes for things we don't have
upstream bindings for unless we've inherited them from Linux.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
If supported by the SPI instance and soc, this property will
configure the frame-format to be compliant with the TI mode.
By default, if supported, the frame-format is Motorola mode.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add DT bindings for the optional Interrupt Translation Service module
of the ARM GICv3 Interrupt Controller.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
