This test is failing on platforms requiring a bigger stack size. This
issue is fixed by adding the missing CONFIG_TEST_EXTRA_STACKSIZE to
tweak the thread stack size.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Fix scanning so that we always use active scanning in case the UUID we
are looking for is in the scan response, and disable duplicate filtering
to handle devices that modify their advertising data at runtime, such as
smartphones reacting to apps being opened and closed.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Update the sample to indicate which device it was using, which helps
mitigate the existing problems identifyin Arduino I2C buses. Also
output a summary of results so cases where no devices are found
provide output after the Starting... line.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
It is important to clarify when to launch audio capture command in
order to avoid that initial boot characters enter into the audio
file leading to bad initial data.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
As noted in the issue #20666 discussion, though the console is not used
by this sample app, it can't really be "disabled" using this Kconfig
option, so remove the CONFIG_SERIAL=n line.
Fixes: #20666
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Some architectures require more space on the stack when running samples
and tests. Use the CONFIG_TEST_EXTRA_STACKSIZE also on the philosophers
sample to deal with such cases.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
A reference to CONFIG_CAN_AUTO_BOFF_RECOVERY was added in commit
1b88658f9f ("samples: driver: Extend CAN sample"), but it's never been
defined as a Kconfig symbol.
Should have been CONFIG_CAN_AUTO_BUS_OFF_RECOVERY according to
alexanderwachter, so change it to that.
Adding detection of unused symbols in samples and tests to CI.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Corrected spellings in printk messages plus removed
unnecessary blank lines.
In case of Gen. Move client's message to Server, reduced
values of delta & transition time to improve demonstration.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
The device address can only be 0x18 through 0x1F. C6 is connected to
the FXOS870 and is not exposed on a header: switch to Arduino D0.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The i2c_msg API details do not work correctly with Nordic TWI. Switch
to the higher-level and simpler API for register read and write. Also
add a tree configuration on a Nordic-based board.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Commit 16d8ce519c introduced changes
that caused this sample to no longer behave according to documentation
and for some hardware to no longer work at all.
On nRF51 SoCs for instance, the reported number of cycles per second
is 16M, what makes the calculated max_period and min_period to be 16
and 0 microseconds, respectively, what effectively makes it impossible
for the sample to return to the initial blinking frequency. Moreover,
with such short PWM periods, the blinking is not even noticeable.
This patch partially reverts the changes mentioned above, and instead
of calculating max_period and min_period basing on the reported clock
rate, it tries to only decrease the max_period if needed, accordingly
to what the used hardware can handle.
Documentation is also updated to mention the possible change in
observed behavior of the sample on some hardware.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Name convention for nordic USB driver changed
Kconfig files for custom boards have to be udapted accordingly.
Changes affect only name convention change.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
By adding new SoC to Zephyr drivers has to be updated.
Commit affects:
- USB driver
- support for nRF52833 added.
- support for USB_DEVICE_REMOTE_WAKEUP in hid-mouse added.
- SPI
- IEEE 802.15.4
- CLOCK CONTROL
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
There are compiler error about the entry functions of two threads
not returning anything. So add return statement to fix it.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Removed unnecessary global variable & replaced them with different
variable defined in struct light_ctl_state.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
Removed redundant coding which was related to old implementation.
Now Server will publish the new state information to the model’s Publish
Address only when there is mismatch between target & current values.
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
Fix build reply function. The sample uses return value
from net_pkt_read() to determine data length,
but the return value is 0 on success.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add internal API to enter and exit deep power-down mode. Add Kconfig
option to return to DPD whenever device is not active.
When device power management becomes more mature it should be possible
to implement it, which would allow use of DPD without having to enter
and exit DPD between consecutive transactions.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This commit converts the existing hcm5883l 3-axis magnetometer
driver to use device tree for the I2C and GPIO selection.
It also adds a basic sample application for this sensor, using the
frdm-k64f development board to demonstrate how the interrupt
GPIO pin and I2C bus can be selected.
Signed-off-by: Kevin Townsend <kevin@ktownsend.com>
Add a special target that's marked build_only so the BLE SW LL
implementation on VEGABoard is built daily. This helps ensuring
that it doesn't get inadvertedly broken by subsequent updates.
The name of the target is peripheral_hr_rv32m1_vega_ri5cy
and it can be run with the following command:
sanitycheck -v --all -p rv32m1_vega_ri5cy \
-x=CMAKE_REQUIRED_FLAGS=-Wl,-dT=/dev/null \
--test samples/bluetooth/peripheral_hr/\
sample.bluetooth.peripheral_hr_rv32m1_vega_ri5cy
Note: The extra CMake flags are required if running with the official
VEGABoard compiler, due to this linker issue:
https://github.com/pulp-platform/pulpino/issues/240
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Add the required specific HW configuration for SW defined
BLE LL on RV32M1 SoC, by means of DTS overlays:
- enable INTMUX0 channels 2 & 3
- route Generic FSK RF0 interrupt to INTMUX channel 3
- route LPTMR1 interrupt to INTMUX channel 2
This change is done for all Bluetooth samples that are intended to
run on RV32M1 using BLE SW LL.
Signed-off-by: George Stefan <george.stefan@nxp.com>
Signed-off-by: Radu Alexe <radu.alexe@nxp.com>
Signed-off-by: Ionut Ursescu <ionut.ursescu@nxp.com>
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Complement GPIOTE HAL function calls with the NRF_GPIOTE parameter.
Update nrfx_gpiote_init() function call with the newly introduced
parameter.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Convert bmg160 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert bmm150 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert max44009 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert mcp9808 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert sx9500 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert tmp112 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert th02 sensor driver and sample app to utilize device tree.
Introduce a dts board overlay on the frdm_k64f board to ensure we at
least have a single platform in which the sample gets built.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Mark the old time conversion APIs deprecated, leave compatibility
macros in place, and replace all usage with the new API.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Several macros were documented as deprecated but lacked the
infrastructure to produce deprecation warnings. Add the deprecation
marker, and fix the in-tree references to the deprecated spellings.
Note that one non-deprecated macro should have been deprecated, and
is, referring to a newly added line control bit.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Adds the model extension concept to the access layer, as described in
the Mesh Profile Specification, Section 2.3.6. Extensions are
implemented as a tree, using two pointers in each model:
The extends pointer points to the first extended model, and the next
pointer points to the next sibling or (if the NEXT_IS_PARENT flag is
set) the parent model in the tree, forming a cyclical "Left-child
right-sibling" (LCRS) tree. The tree root can be obtained by calling
bt_mesh_model_root_get(), and the extended models can be walked by
calling bt_mesh_model_tree_walk().
According to the Mesh Profile Specification Section 4.2.3, all models in
the same extension tree share one subscription list per element. This is
implemented by walking the model's extension tree, and pooling the
subscription lists of all models in the same element into one. If the
config server adds a subscription to a model, it may be stored in any of
the model tree's models' subscription lists. No two models in the same
extension tree and element will have duplicate groups listed. This
allows us to increase extended models' capacity for subscriptions
significantly.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Replace CONFIG_WDT_0_NAME with DT_ALIAS_WATCHDOG_0_LABEL in samples and
test code. Now that all drivers are DT aware we don't ever set the
Kconfig option.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
