The board name for the Thingy:52, so far known as nrf52_pca20020, is
renamed to thingy52_nrf52832. Its documentation and all references to
its name in the tree are updated accordingly. Overlay and configuration
files specific to this board are also renamed, to match the new board
name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Additionally remove udoo_neo_full_m4.conf from gpio_basic_api test since
the Kconfig symbols don't need to be set anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
- Updates gpio driver and device tree files to the new GPIO Config flags
- Implements the new port_* APIs
- Update I2C and PWM Drivers to use new GPIO config
- Add esp32.overlay to gpio_basic_api test
- refactor convert_int_type, regs struct
- remove config_polarity
- add kConfig notes
Tests:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_basic_api
- tests/drivers/gpio/gpio_api_1pin
Board:
- esp32 DevKitC V4
Note about interrupts:
The ESP32 requires specifying a CPU interrupt to be used for GPIO
interrupt signals. CPU interrupts can be either level or edge (or
special) triggered, but not both.
Please check gpio/Kconfig.esp32 for more info.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
Enables the 2-pin gpio test on the rv32m1_vega_ri5cy board by adding a
dts overlay and configuring pinmuxes on the arduino header.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
LPC54114 to use D0 and D1 pinout.
LPC55S69 to use A0 and A1 pinout.
2 pin test gpio_basic_api uses pins set up in boars' pinmux.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Added configuration for the udoo_neo_full_m4 board and
the initialization of its GPIO test pins via IOMUX controller.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Enables the 2-pin gpio test on the mimxrt1050_evk board by adding a dts
overlay and configuring pinmuxes on the arduino header.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adding overlays so that users can run this test on the following
boards:
- cc3220sf_launchxl
- cc3235sf_launchxl
- cc1352r1_launchxl
Instructions on pins to connect are included in the overlay files.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API.
Tested on external SX1509B breakout board and Thingy:52.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Test that the new port API functions all behave as expected, including
physical vs logical level for input and output as well as masked and
set-based output operations. Also tests the new pin API functions.
For running on real hardware this test now uses a local test-specific
devicetree binding. For build-only tests any platform with a GPIO
alias should be tested.
The new code increases flash requirements so add a filter to exclude
platforms that won't link.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
