Move the common tunnel setup code to samples/net/common directory
so that other network samples can utilize that too.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Now that nRF70 by default uses zero-copy fine-tune the configuration to
get optimal memory while getting peak throughputs.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Enable wifi node in all procpu dts, so Wi-Fi could be enabled simply by
enabling the CONFIG_WIFI. In turn some sample code overlay files can be
dismissed.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
It is easier to separate a sample application Kconfig
values from ones that configure something inside Zephyr.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Add support for running LwM2M client on nRF52840 chip
using nRF9160 as a modem through serial port.
nRF9160 should run Serial LTE Modem application build
from nRF Connect SDK.
nRF9160DK board has two MCU, nRF9160 and nRF52840.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
OVERLAY_CONFIG has been deprecated and replaced by
EXTRA_CONF_FILE. Update samples to reflect that.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add support for DICONNECT message specified in MQTT 5.0.
As with MQTT 5.0, the disconnect can now also be initiated by the
broker, it was needed to add decoder support for the message.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Allow configuring MTU for CMUX.
Some AT manual and specification define this as a
frame size. Linux ldattach default to 127 bytes,
3GPP TS 27.010 defaults to 31.
We should limit our CMUX frames to a size that
remote end is capable of handling.
Linux silently drops oversized frames.
Also, remove MODEM_CELLULAR_CMUX_MAX_FRAME_SIZE as
this was only limiting a buffer sizes, and resulted
CMUX frames to be capped to same value.
Use MODEM_CMUX_WORK_BUFFER_SIZE and MODEM_CMUX_MTU instead.
Also rename CONFIG_MODEM_CELLULAR_CHAT_BUFFER_SIZES to
CONFIG_MODEM_CELLULAR_CHAT_BUFFER_SIZE as it is now
only used as a Chat module. DLCI pipes use
CONFIG_MODEM_CMUX_WORK_BUFFER_SIZE.
Signed-off-by: Seppo Takalo <seppo.takalo@nordicsemi.no>
Add ULP Coprocessor board support for C6.
This requires a change in the board qualifier depending on the build
target.
Update esp32c6 overlay and configuration files to the proper name.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
TLS_CREDENTIAL_SERVER_CERTIFICATE credential type is misleading, as in
fact it just represents a public certificate, it does not matter if the
certificate belongs to a server or a client. And actually, it was
already used in-tree for clients as well, for example in LwM2M.
Therefore rename the credential type to a more generic
TLS_CREDENTIAL_PUBLIC_CERTIFICATE and deprecate the old one.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
nRF70 driver now uses a separate heap, so, no need to explicitly
configure the kernel heap.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Move the common VLAN setup code to samples/net/common directory
so that other network samples can utilize that too.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Move the common VLAN setup code to samples/net/common directory
so that other network samples can utilize that too.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Move the common VLAN setup code to samples/net/common directory
so that other network samples can utilize that too.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Move the common VLAN setup code to samples/net/common directory
so that other network samples can utilize that too.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Move the common VLAN setup code to samples/net/common directory
so that other network samples can utilize that too.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Add `overlay-dhcpv4.conf` for using this sample with DHCPv4.
When the DHCPv4 client is enabled, we must have a large number
for `CONFIG_ZVFS_EVENTFD_MAX`.
This sample may be frequently used with the DHCPv4 client,
so we'll add the extra config file.
Signed-off-by: TOKITA Hiroshi <tokita.hiroshi@gmail.com>
Clarify the documentation in the README.rst file. Also remove the
obsolete comment from main.c as it is no longer correct.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
Expect that networking is properly setup, by expecting
NET_EVENT_L4_CONNECTED event and listening for TCP/UDP incoming traffic on
both IPv4 and IPv6.
Signed-off-by: Marcin Niestroj <m.niestroj@emb.dev>
Previously the net_linkaddr struct had pointers to the link address.
This is error prone and difficult to handle if cloning the packet as
those pointers can point to wrong place. Mitigate this issue by
allocating the space for link address in net_linkaddr struct. This will
increase the size of the net_pkt by 4 octets for IEEE 802.15.4 where the
link address length is 8, but there no increase in size if link address
is 6 bytes like in Ethernet/Wi-Fi.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
CONFIG_ETH_NATIVE_POSIX is deprecated in favor of
CONFIG_ETH_NATIVE_TAP, let's replace it.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This should allow an issue such as #86681 to be found earlier for a not
widely used config.
Signed-off-by: Etienne de Maricourt <edmecomemail@gmail.com>
Rename the driver from uart_native_posix to uart_native_pty.
Including renaming the DTS compatible, and kconfig options, deprecating
the old ones.
And refactor the driver, generalizing it, so we can have any number of
instances.
Note that, unfortunately generalizing to N instances cannot be done
without a degree of backwards compatibility breakage: This driver was
born with all its configuration and selection of the instances based on
kconfig.
When the driver was made to use DT, it was done in a way that required
both DT and kconfig needing to manually coherently enable the 2nd UART.
This has now been fixed, which it means only DT is used to decide how
many instances are avaliable, and UART_NATIVE_POSIX_PORT_1_ENABLE is
just ignored.
Including:
* Deprecate UART_NATIVE_WAIT_PTS_READY_ENABLE: the options is always on
now as it has no practical drawbacks.
* Deprecate UART_NATIVE_POSIX_PORT_1_ENABLE: DTS intanciation defines it
being available now.
* Rename a few functions and in general shorten pseudo-tty/pseudo-
terminal to PTY instead of PTTY.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Replace a few references to native_posix / the native_posix ethernet
driver with native_sim, or native_tap.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Rename this driver to eth_native_tap, including renaming all its
options.
The old options remain until v4.4, but as deprecated.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Lookup the address of the SNTP server through DNS instead of requiring
a server to be running locally.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Networking events may have been triggered before `wait_for_network` was
called. Resend the status events after the callbacks have been
registered.
Signed-off-by: Jordan Yates <jordan@embeint.com>
native_posix is being removed as it has reached its end of life in 4.2,
after being deprecated since 4.0.
So these overlays will not serve any purpose anymore.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
native_posix is being removed as it has reached its end of life in 4.2,
after being deprecated since 4.0.
Remove the twister support for native_posix[//64] and therefore all
references to them from the testcases and samples yamls, so twister
does not error out.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
This driver was deprecated and must be removed by Zephyr version
4.1 according to lifecycle/release guidelines.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Call coap_client_cancel_requests() before closing the client socket so
that all activities on that socket are ceased before close. This
prevents POLLNVAL error from being thrown by the coap_client thread and
error being printed in the sample output.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
In the above file, Building,Flashing and Running section is using
:zephyr-app: as samples/boards/espressif/deep_sleep.
But it should be samples/net/wifi/apsta_mode.
Fixes: #85505
Signed-off-by: Ram Mahesh <rammaheshram1234@gmail.com>
Add frdm_mcxw7 board conf and overlay files for echo_client and
echo_server sample applications.
Signed-off-by: Andrei Menzopol <andrei.menzopol@nxp.com>
Decouple dependency of CONFIG_NXP_WIFI_SOFTAP_SUPPORT.
Add wifi defconfig to set default kconfig options when soft AP
enabled.
Signed-off-by: Fengming Ye <frank.ye@nxp.com>
