This adds to the usual qemu_x86_64 and qemu_cortex_a53 to
the entries for Sys-T catalog message in sample.yaml.
As the Sys-T backend has been updated to support 64-bit
for catalog messages.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The BT tiny configuration has been removed some time ago,
but documentation has been still referencing it.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Recently OpenAMP introduced the possibility to set the sizes for TX and
RX buffers per created instance. Expose this also to Zephyr users by
using a DT property "zephyr,buffer-size".
For the sake of simplicity use the same DT property to set the buffer
size for both TX and RX buffers.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Provided sample support for Telink tlsr9518adk80d board.
Set CONFIG_BT_TINYCRYPT_ECC=n (supported by BLE controller).
Signed-off-by: Yuriy Vynnychek <yura.vynnychek@telink-semi.com>
Set the TF-M profile type to none for TF-M integration samples.
If the default profile has been set to something else these samples may
fail.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Adjusted Bluetooth parameters that have an impact on MTU and DLE
negotiation during a connection.
Enabled the Packet Reassembly feature from mcumgr libraries in the SMP
Server sample with the Bluetooth transport configuration. This change
should increase the overall throughput of the DFU process over
Bluetooth.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
This PR adds a soft off mode to the RT10xx Power Management API.
Additionally, it corrects the PM API function in rt10xx_power.c to
use the correct function prototype to be properly overridden.
Signed-off-by: Nickolas Lapp <nickolaslapp@gmail.com>
The ISO security implementation works by verifying
against the acl (bt_conn) sec_level field. The
bt_conn sec_level field is only available
if CONFIG_BT_SMP is enabled, so this commit
adds guards for all ISO security checks as well.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This is a follow-up to commit f5ffd05e6b.
Since twister removes leading spaces from received lines before
further processing, the regular expression for checking the output
produced by the sample cannot contain such space. Also negative
values read from ADC channels need to be allowed.
For consistency, remove the leading space also in the actual string
printed by the sample.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This dependency it is not required since majoprity of platforms are
working with new pinctrl API. This drops the pinmux dependency.
Fixes#46091
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This commit fixes the stale reference to the devicetree
`clock0@82005000` node, which was changed in the commit
7b601b7f50.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
off_t is often unsigned long, which means printf needs to use %lx. Insert
a cast in case the value is unsigned int.
Signed-off-by: Keith Packard <keithp@keithp.com>
Adds few missing zephyr/ prefixes to leftover #include statements that
either got added recently or were using double quote format.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
As per 'Adding Secure Partition' in the TF-M documentation,
every secure partition must have a unique 32-bit partition ID.
If no value is provided, one will be auto-allocated by the
TF-M build system, but this can lead to unpredictable behaviour
in some cases. One example is key derivation where the partition
ID is used as part of the key derivation inputs. Different builds
can results in different PID values being assigned, resulting
in inconsistent key derivation output.
To avoid these problems, this commit sets a fixed PID as a
best pratice.
A value of 1000 has been set to place it within the
'PSA and user Partitions' range (256 - 2999) described in the
documentation.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
Fix various board fixed-partition definitions where the devicetree cell
has been defined oddly, such as 9 nibbles (which makes no sense since
the cells are 32 bit) or 7 nibbles where all the others are 8.
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
The sample did not have defined pass condition and was failing
due to a timeout. Add harness: consol and an explicit regex matching
the sample's output so it can pass on a hw. In addition, a requirement
for a gpio_loopback fixture was added to the sample.yaml.
fixes: #45229
Signed-off-by: Maciej Perkowski <Maciej.Perkowski@nordicsemi.no>
The check did not properly check the info->flags as a bitfield,
and thus never decoded the data.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Define the configuration through an overlay file
to run the sample on the nucleo_h743zi target board.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
It has been validated that the nucleo_h743zi board works correctly,
with '__nocache' buffers and data caches enabled, so this patch enables
support for the former.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Adds mps3_an547_ns to certain TF-M samples to improve
testing in CI by including the Arm Cortex-M55 platform.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
Removes lpcxpresso55s69_ns from certain sample.yaml files due
to changes required for TF-M 1.6.0 not being added to the
upstream project before the 1.6.0 release.
The NXP SDK available for download from NXP contains the required
updates, but these will need to be committed to TF-M, then made
available in the Zephyr fork, at which point the yaml files here can
have the LPC added back.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
Increases the scan and adv data sizes to better support
the extended advertising data and periodic advertising
data (BASE).
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Clean up some of the board specific configuration files.
Removed all CONFIG_BT_CTLR* configs from the nRF5340
appcore conf files as that does not compile the controller.
Ensured that the ISO buffer in the controller for
nRF52840 can contain SDUs from all BAP LC3 minimum
requirements, as the controller does not yet
support segmentation of SDUs.
Also fixed a few bad configurations (broadcast sink not
enabling the sync support etc.).
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add specific configuration and DTS overlay files for NUCLEO-H7A3ZI-Q
board to the littlefs example project. The second half of the SOC flash
is used as flash partition for littlefs.
Signed-off-by: Christoph Heller <chris@metanetics.de>
This commit changes the pointer type used in the philosophers demo to
`stack_data_t *` when stacks are used for synchronization purposes.
The previously used `void *` was causing AMO address-misaligned
exception on the HiFive Unleashed platform.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
On the stm32l073rz nucleo and stm32f091rc nucleo
boards, the DTS pwm-leds node is disabled, because
the output pin might conflict with SPI1.
It is necessary to enable the node in the overlay
to compile and run the sample.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Remove the explicit enable of Extended and Periodic
Advertising support in Controller, the feature is no
longer experimental in the Controller and is now enabled
by default when application uses them by enabling as
Host feature.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Add a call to bt_iso_chan_get_info for each CIS in the sample
to ensure that we don't attempt to send any data on a CIS
that is RX only.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
integration platforms can't be filtered out, adapt tests so that those
platforms are always available for testing.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
integration platforms should not be in common section if we have
scenarios with different set of integration platforms.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The lmp90100_evb sample included an implementation of double sqrt, and the
on_off_level_lighting_vnd_app sample included an implementation of float
sqrtf. Move that code into minimal libc instead of requiring applications
to hand-roll their own version.
Signed-off-by: Keith Packard <keithp@keithp.com>
The overlay for the nRF52840 DK board uses ADC controller child nodes
for specifying channel configurations and it shows how to configure
a channel in differential input mode, so it can serve as an example
of how to use these new possibilities. The overlay for the nRF51 DK
board shows how to use a specific ADC resolution (the default 12 bit
setting is not supported by nRF51 SoCs).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Allow specifying configuration of channels through child nodes of ADC
controllers. This way analog inputs can be specified for channels in
SoCs that require this and it is also possible, for example, to use
different gain or reference selections for particular channels.
This commit also removes a few former limitations of the sample: now
it is possible to use more than 2 channels and each channel can use
a different ADC controller. Also the ADC resolution to be used can be
specified through devicetree.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add two new Kconfigs: BT_ISO_CENTRAL and BT_ISO_PERIPHERAL
that is used to do central or peripheral only builds,
similar to the BT_CENTRAL or BT_PERIPHERAL Kconfigs.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
This add a new sample application to test and validate
the stm32 octospi driver on the NOR octo-flash present on
stm32 disco kits
There should be a special case to erase the complete flash.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Increase the heap size for RT1170 EVK to allocate the
display buffers for a 720x1280 display
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
mps2_an521 and mps3_an547 need yet more time with TFM 1.6 to pass their
tests. This change was recomended by RajKumar Kanagaraj. Thanks!
Signed-off-by: Jimmy Brisson <jimmy.brisson@linaro.org>
Since the recent OpenThread update, OT needs more stack to initialize,
therefore bump the stack size in samples using OpenThread.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
The overlay was accidentally pushed as part of another commit while
doing some pinctrl/pwm tests.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
This is the same fix as the one introduced in 49520eea57 ("samples: nrf:
system_off: Fix force state usage") for nRF boards. Quoting original
commit:
The sample cannot spin in an infinity loop because the idle thread
will not run and consequently the forced state will not be used.
Without this fix, the system doesn't enter SOFT_OFF state:
*** Booting Zephyr OS build zephyr-v3.0.0-3495-ga456c5274614 ***
cc1352r1_launchxl system off demo
Busy-wait 5 s
Sleep 2000 us (IDLE)
Sleep 3 s (STANDBY)
Entering system off (SHUTDOWN); press BUTTON1 to restart
ERROR: System off failed
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
